I've got GSA-H20L LG lightscribe drive but the only problem is that the lightscribe drivers I got from versiontracker have to no avail helped me, I also tried disclabel.
Is there anyway via drivers/program to get lightscribe to work on this sawtooth?
trying to install Tiger on a 350mhz Sawtooth - problem is the computer won't read the dvd/cdrw drive (it did fine before I formatted the HD). I try holding C, it does nothing, tried reseting PRAM, nothing.
View 4 Replies View RelatedI have a powermac G4 Sawtooth and the power supply recently decided to go, My question is, is there a way to tell if I have a Rev.1 or Rev.2 just by looking at the board? Markings on the case and PSU don't help because I bought a Replacement Motherboard for it which had wider white plastic clips, I need to know because I am not sure if i need the 237W PSU or the 200W PSU.
View 4 Replies View RelatedI'm working on upgrading my 400MHz Sawtooth. I'd like to take it to the maximum 2 GB of RAM, but since I already made the mistake of buying high density instead of low, I thought I'd ask before making another purchase.
As far as I know, these are the right specs for my machine:
-PC100 (or faster) SDRAM
-low density
-non-ECC
-max 512 MB
-double sided
so my pc ftp server starts being a bh so i put all the drives into my pm g4, press power it chimes, screen is blank, i have followed the 'my mac won't boot guide' so please don't point me to that
View 9 Replies View RelatedI've been a PC user for many many years, but have had a G4 Sawtooth for about 3 years now, its only a 400Mhz model, but I have just placed a 533Mhz G4 in there, and apparently I need to use a dip switch? I just got a standard sized dip switch, so thats not a problem, I was wondering two things:
1. If anyone has a Sonnet for sale instead of using the G4
or
2. If you can offer up some advice on the easiest way for my G4 to recognise the new 533 CPU?
My last Powermac G5 I put in the 20x dual layer Pioneer. 116d I think is the model number. Works perfect. Should I get that same drive or should I get the Pioneer one that has the 20x dual layer plus Lightscribe? I heard the Lightscribe one is basically an Asus drive and don't know if that is good or bad. Does anyone use Lightscribe?
View 5 Replies View RelatedWell, using some guides (check bottom of post), I did some experimenting with my old G4 Sawtooth to see how fast I could run its lame 400mhz cpu. Ultimately, my goal was to make Quake 3 playable at a resolution other then 800x600. These tests were all done with PC-133 ram (896MB), running 10.4.11.
Starting specs:
400mhz (4x100mhz)
Xbench cpu score: 19.9
1st overclock (with 400mhz cpu):
500mhz (5x100mhz)
Xbench cpu score: 29.3
Note: This was incredibly unstable.
In the process of moving to 450mhz on the 400mhz stock cpu, one of the jumper resistor solder pads came off (lame 10 year old glue). So, I went on ebay and got 5 450mhz G4 cpus for 50$ CDN after shipping. One of them came dead, and one failed after the jumper change.
2nd overclock (with 450mhz cpu):
500mhz (5x100mhz)
Xbench cpu score: 22.3
Note: This sucked. Now really stable, but I didn't get a performance gain like I got with the 400mhz cpu, and Quake 3 still ran like crap.
So here I decided to do the FSB overclock. Knowing I would end up with 4.5 x 133 which would be too fast, i jumpered a cpu to 3.5 multiplier for a 466 clock. This never booted. I put in a 450mhz chip and...
3rd overclock (with 450mhz cpu):
533mhz (4.5x133mhz)
Xbench cpu score: 25.6
Note: That multiply doesn't make sense. It shouldn't be 533. But hey, it worked, stable, and I got a performance gain.
4th overclock (with 450mhz cpu):
533mhz (5x133mhz)
Xbench cpu score: 29.3
Note: Ok, the clock is still not right. This is the same cpu that did the 5x100 so I know the multiplier is set right. But hey, its doing better in the scores!
Conclusion: Success! 533mhz seems to be the top out with the NVRAMRC script in place. But there is a considerable performance gain everywhere (booting, app loading, etc). Most importantly, my Quake 3 now runs very smooth @ 1280x1024 with max graphics settings. I am a very happy camper. I can take pictures of the solder job if anyone requests them. I do recommend this if you have some good technician skills.
i recently bought a secondhand mac g4/400 and ive been trying to startup to install tiger (am using a macbook pro for work). i tried both of the ultra ata 'bays' but am wondering whether normal IDE drives will work?
i have:
1X western digital (caviar) enhanced IDE drive and
1X seagate normal IDE drive (ST340015A)
the cd-rom works fine on its own and can boot up with panther install discs but when selecting startup disc there is nothing. I connected the cdrom to the far end of the cable (set jumper to master) and WD E-IDE drive to the second 'block' (set as slave)
i am under the assumption that because the cdrom works there is nothing wrong with the cables.
on boot up I cant select the startup drive (just network) as there is only one device detected (CDROM) if harddrives are disconnected
I get the network folder first on boot up then question mark/folder icon
not quite sure how to proceed from here. is formatting a must for the normal IDE drive? or will the mac pick it up regardless.
I connected both drives to existing cables and the normal IDE drive also to IDE (PC) cable also reset the PMU/SMU as well as took out all daughterboards and tested RAM which appears to be ok. i also took out the battery and put it back.
the PSU seems fine, but is there a way i can check with diagnostics or something..
I running a 400MHz sawtooth Family #M5183 my friend gave me with a 40 gig hard drive running OSX 10.3.9. I just picked up at the swap meet a Qwicksilver Model No.M849 PNG4 1GHZ DP/2M CACHE/512MB SDRAM? 80GB HD DVD-R/CDRW/Nv17 DUAL/56k MDM/GIGE it is missing the HD from under the superdrive can I just plug in the HD from my Sawtooth and run her? She still has the HD in the bottom its a 80 gig IBM Deskstar. When I opened my Sawtooth I found that there is a Seagate Cheetah model#*ST118202LW* Its not even plugged in!!! How many gigs is it and can i run it for more space? I have three 512 cards for memory. Can I use the video card from the sawtooth to run a second monitor? If this all works whats the newest operating system I can run? As soon as I get the money I am going to swap the processor and bring her up to speed. I am a singer/songwriter on a budget trying to put my studio together,I run live sound and make Hand Drums.I'm not a computer tech by no means but I do ok running a mouse to get a good sound. If you are going to tell me to wrap machine in tin foil and put it in the freezer PLEASE don't waste my time!!!!! I just want to build my machine correctly and not f@#$ anything up.
View 6 Replies View RelatedI want to do this to increase the speed of my sawtooth. I think that the dual 500mhz was the last apple processor that is compatible with the sawtooth because they both run on 100mhz busses, correct?
View 4 Replies View RelatedI have an old sawtooth and like many people find the prices of the original airport card to be a bit inflated.
I read that lucent Wavelan silver, bronze, gold cards are backwards compatible with the original Airport specs.
Does anyone know if this works for certain? If it does, I'd like to pick one up cheap from ebay and stick it in my Sawtooth.
After packing away my little brothers sawtooth 400Mhz with 384mb RAM and an 8Mb ATI AGP graphics card and then unpacking it I've been having a problem. When starting the computer up the screen shows nothing at all I have tested to see if the screen is broken and it seems to be functional. I think the card itself might be broken? BTW, I'm using the VGA slot and not the DVI slot on the back. I have also removed and cleaned the card just incase that might've been the problem.
View 3 Replies View RelatedToday I was planning to build in a second harddrive into my old G4 tower. So I did this. But after installing the system won't boot anymore from the OS X Tiger partition. I have tried all sorts of jumper settings, from slave to master to cable select. All without success.
When I boot from the Tiger installation CD diskutility does not even recognize my original master drive nor does it recognize the new slave drive. I even tried to boot from an old OS9 disk to initialize the disk. I tried formatting it in another machine to HFS Journaled, no success in booting mounting the disk whatsoever.
I recently added some extra RAM's but i doubt these are the problem since my machine DOES boot without having the new disk installed in the system.
It is a 60GB Maxtor drive, so it is within the maximum amount of GB's possible for these older machines.
[URL]
Our church is possibly going to get a mac pro to replace our current windoze projection system. This system will also be used to edit/record video and then burn it onto a DVD. My question is, what lightscribe drive will work well that will fit as seamlessly as possible in the Mac Pro's drive bay?
View 24 Replies View RelatedHope I can ask this here. I installed Snow Leopard and now have copied a cd. I have a LaCie dvd copier with Light Scribe. I used the LS and it ran normal but when finished the disc had nothing on it. I went to the LaCie sight and nothing is mentioned about Snow Leopard.
View 1 Replies View RelatedI have this memorex lightscribe external burner. before I open it i want to make sure it is MAC compatible. I want to burn CD and eventually dvdsDoes not mention Mac anywhere on the box. I have a 24" mac desktop
View 10 Replies View RelatedI guess there's not much more to this question than that:
http://www.newegg.com/Product/Produc...-333-_-Product
Can I install this in my 2008 mac pro and use the lightscribe functions?
Has anyone tried to use an HP1040E on a mac?. It is supposed to be a plug and play device. It was sold as mac compatible however is not recognised!!
View 1 Replies View RelatedCan I use lightscribe discs with my iMac
Info:iMovie '11, Mac OS X (10.6.7)
I recently upgraded my old Airport Extreme Base Station (looks like a lumpy cap) to a newer AirPort Extreme Base Station with dual-band support and 802.11n. I installed the software on my Macbook running Snow Leopard, created a new set up with new passwords, etc. The Macbook and a G4 12" rev A PowerBook running OS 10.3.9 connect fine, but a G4 500 GHz Sawtooth, running OS 10.3.9, with an original Airport card installed will not connect. Initially the new networks showed in the AirPort inverted triangle bars, but now the triangle is grey, and I can't get any connection with Internet Connect or the network diagnostic that comes with the OS. 2 out of three ain't bad, but I want all the computers to connect.
View 1 Replies View Relateddoes it have lightscribe technology or something? or... just a big fraud, cause they cost 100$ i am guessing that they can read discs really fast
View 18 Replies View RelatedSo i didnt really know where else to ask but my lightscribe software is not buring discs correctly under snow leopard. Im currently using the lacie disc labeler. I wanted to know if anyone else is experiencing the same problem or knows of any other software to try other than disclabel which is working somewhat but only allows me to burn a label the size of half the cd.
View 24 Replies View RelatedI've got an iMac 17" Intel Core duo. I would like to know for those who got the same model, if the matshita internal optical drive ( MATSHITA DVD-R UJ-85J ) is compatible Lightscribe ?
View 2 Replies View RelatedI was wondering if there is such a thing as a external dvd burner with light scribe for my mac ibook g4?
View 3 Replies View RelatedWhen I Put A 20X Sony Lightscribe� Drive In The Secondary Optical Bay I Attached The Power And The IDE, I Checked To See If The Drives Were Initialized They Were Not Even Recognized.....The New Sony As Well As The Apple Stock Drive In The First Bay It Was Like I had Removed Both Of Them! I Then Took Out The Apple Stock Optical And Put The New Sony Lightscribe Drive In Its Place, Leaving Only The One New Sony Drive In The Pro, It Was Recognized By The System However Would Not Open Due To The Fact That The Opening On The Mac Was To Small For The Shelf Of The Drive To Open. It Was Blocked! WTF!
I Instantly Thought I Must Have Messed Up The Install, However I Thoroughly Checked It Over And There Is Really No Way For Me To Mess It Up. Due To Where The Screws Line Up. It's Not Possible To Screw Up! No Pun intended. So Whats Left Now? I Thought These Optical Drives Where Like Internal Hard Drives, USB's And Blank Disks...They Have Standard Dimensions For ALL CPU"S I Did not know that there are incompatible optical drives! Does Anyone Know A: What Drives Are Compatible With The Xeon Mac Pro?
Why doesn't LightScribe work with my Snow Leopard? It downloaded and is in my printer folder, but won't open.
Info:
Mac OS X (10.6.3), HP LightScribe
I just replaced the HD in an iBook G3 I have laying around with a toshiba 40gb. The install went fine and I formatted it in disk utility using mac os x extended (journaled). I ran it for errors and it checked out fine. I also ran the apple hardware test CD and everything checked out there too. The problem is I am getting a kernal panic no matter what I do. I started off installing 10.3 and the first disc installs fine, but then when it restarts it gets an instant kernal panic. I tried 10.4 with the same results. Then I tried the 10.2 discs that the iBook came with and it would get the very last step of the install on the 1st disc and would not go any farther. It said "one minute remaining" for over an hour.
I have taken a picture of the error log that shows up and you can see here: The top line got cut off but it says "panic(cpu 0): Unable to find driver for this platform: "PowerBook4,3" Like I said, everything checks out hardware wise and i have tried three different versions of OS X.
Anyone knows if the install cds shipped with the macbook pro C2D are able to install OSX on a PPC mac. Macbook pro install CD to install tiger on a G4 Powerbook?
I have a power mac g5 its a few years old and I'm having trouble installing OS 10.5 leopard. When I turn on the computer i get a blinking ? folder that alternates showing a ? and a mac face, with a gray background. I tried putting in the start up disk (? folder doesn't appear with the start up disk) and it guides me through the installation steps, but it doesn't display a location to install the OS on. I also tried putting an external HD in and this does not appear as well. So, I went to disk utility and tried the figure out the problem. In disk utility, the internal hard drive is there, but not the external HD. I also tried switching Hard drive ports from a to b and this made no difference.
View 11 Replies View Related