so my pc ftp server starts being a bh so i put all the drives into my pm g4, press power it chimes, screen is blank, i have followed the 'my mac won't boot guide' so please don't point me to that
View 9 Repliestrying to install Tiger on a 350mhz Sawtooth - problem is the computer won't read the dvd/cdrw drive (it did fine before I formatted the HD). I try holding C, it does nothing, tried reseting PRAM, nothing.
View 4 Replies View RelatedToday I was planning to build in a second harddrive into my old G4 tower. So I did this. But after installing the system won't boot anymore from the OS X Tiger partition. I have tried all sorts of jumper settings, from slave to master to cable select. All without success.
When I boot from the Tiger installation CD diskutility does not even recognize my original master drive nor does it recognize the new slave drive. I even tried to boot from an old OS9 disk to initialize the disk. I tried formatting it in another machine to HFS Journaled, no success in booting mounting the disk whatsoever.
I recently added some extra RAM's but i doubt these are the problem since my machine DOES boot without having the new disk installed in the system.
It is a 60GB Maxtor drive, so it is within the maximum amount of GB's possible for these older machines.
[URL]
I have a powermac G4 Sawtooth and the power supply recently decided to go, My question is, is there a way to tell if I have a Rev.1 or Rev.2 just by looking at the board? Markings on the case and PSU don't help because I bought a Replacement Motherboard for it which had wider white plastic clips, I need to know because I am not sure if i need the 237W PSU or the 200W PSU.
View 4 Replies View RelatedI'm working on upgrading my 400MHz Sawtooth. I'd like to take it to the maximum 2 GB of RAM, but since I already made the mistake of buying high density instead of low, I thought I'd ask before making another purchase.
As far as I know, these are the right specs for my machine:
-PC100 (or faster) SDRAM
-low density
-non-ECC
-max 512 MB
-double sided
I've been a PC user for many many years, but have had a G4 Sawtooth for about 3 years now, its only a 400Mhz model, but I have just placed a 533Mhz G4 in there, and apparently I need to use a dip switch? I just got a standard sized dip switch, so thats not a problem, I was wondering two things:
1. If anyone has a Sonnet for sale instead of using the G4
or
2. If you can offer up some advice on the easiest way for my G4 to recognise the new 533 CPU?
I've got GSA-H20L LG lightscribe drive but the only problem is that the lightscribe drivers I got from versiontracker have to no avail helped me, I also tried disclabel.
Is there anyway via drivers/program to get lightscribe to work on this sawtooth?
Well, using some guides (check bottom of post), I did some experimenting with my old G4 Sawtooth to see how fast I could run its lame 400mhz cpu. Ultimately, my goal was to make Quake 3 playable at a resolution other then 800x600. These tests were all done with PC-133 ram (896MB), running 10.4.11.
Starting specs:
400mhz (4x100mhz)
Xbench cpu score: 19.9
1st overclock (with 400mhz cpu):
500mhz (5x100mhz)
Xbench cpu score: 29.3
Note: This was incredibly unstable.
In the process of moving to 450mhz on the 400mhz stock cpu, one of the jumper resistor solder pads came off (lame 10 year old glue). So, I went on ebay and got 5 450mhz G4 cpus for 50$ CDN after shipping. One of them came dead, and one failed after the jumper change.
2nd overclock (with 450mhz cpu):
500mhz (5x100mhz)
Xbench cpu score: 22.3
Note: This sucked. Now really stable, but I didn't get a performance gain like I got with the 400mhz cpu, and Quake 3 still ran like crap.
So here I decided to do the FSB overclock. Knowing I would end up with 4.5 x 133 which would be too fast, i jumpered a cpu to 3.5 multiplier for a 466 clock. This never booted. I put in a 450mhz chip and...
3rd overclock (with 450mhz cpu):
533mhz (4.5x133mhz)
Xbench cpu score: 25.6
Note: That multiply doesn't make sense. It shouldn't be 533. But hey, it worked, stable, and I got a performance gain.
4th overclock (with 450mhz cpu):
533mhz (5x133mhz)
Xbench cpu score: 29.3
Note: Ok, the clock is still not right. This is the same cpu that did the 5x100 so I know the multiplier is set right. But hey, its doing better in the scores!
Conclusion: Success! 533mhz seems to be the top out with the NVRAMRC script in place. But there is a considerable performance gain everywhere (booting, app loading, etc). Most importantly, my Quake 3 now runs very smooth @ 1280x1024 with max graphics settings. I am a very happy camper. I can take pictures of the solder job if anyone requests them. I do recommend this if you have some good technician skills.
i recently bought a secondhand mac g4/400 and ive been trying to startup to install tiger (am using a macbook pro for work). i tried both of the ultra ata 'bays' but am wondering whether normal IDE drives will work?
i have:
1X western digital (caviar) enhanced IDE drive and
1X seagate normal IDE drive (ST340015A)
the cd-rom works fine on its own and can boot up with panther install discs but when selecting startup disc there is nothing. I connected the cdrom to the far end of the cable (set jumper to master) and WD E-IDE drive to the second 'block' (set as slave)
i am under the assumption that because the cdrom works there is nothing wrong with the cables.
on boot up I cant select the startup drive (just network) as there is only one device detected (CDROM) if harddrives are disconnected
I get the network folder first on boot up then question mark/folder icon
not quite sure how to proceed from here. is formatting a must for the normal IDE drive? or will the mac pick it up regardless.
I connected both drives to existing cables and the normal IDE drive also to IDE (PC) cable also reset the PMU/SMU as well as took out all daughterboards and tested RAM which appears to be ok. i also took out the battery and put it back.
the PSU seems fine, but is there a way i can check with diagnostics or something..
I running a 400MHz sawtooth Family #M5183 my friend gave me with a 40 gig hard drive running OSX 10.3.9. I just picked up at the swap meet a Qwicksilver Model No.M849 PNG4 1GHZ DP/2M CACHE/512MB SDRAM? 80GB HD DVD-R/CDRW/Nv17 DUAL/56k MDM/GIGE it is missing the HD from under the superdrive can I just plug in the HD from my Sawtooth and run her? She still has the HD in the bottom its a 80 gig IBM Deskstar. When I opened my Sawtooth I found that there is a Seagate Cheetah model#*ST118202LW* Its not even plugged in!!! How many gigs is it and can i run it for more space? I have three 512 cards for memory. Can I use the video card from the sawtooth to run a second monitor? If this all works whats the newest operating system I can run? As soon as I get the money I am going to swap the processor and bring her up to speed. I am a singer/songwriter on a budget trying to put my studio together,I run live sound and make Hand Drums.I'm not a computer tech by no means but I do ok running a mouse to get a good sound. If you are going to tell me to wrap machine in tin foil and put it in the freezer PLEASE don't waste my time!!!!! I just want to build my machine correctly and not f@#$ anything up.
View 6 Replies View RelatedI want to do this to increase the speed of my sawtooth. I think that the dual 500mhz was the last apple processor that is compatible with the sawtooth because they both run on 100mhz busses, correct?
View 4 Replies View RelatedI have an old sawtooth and like many people find the prices of the original airport card to be a bit inflated.
I read that lucent Wavelan silver, bronze, gold cards are backwards compatible with the original Airport specs.
Does anyone know if this works for certain? If it does, I'd like to pick one up cheap from ebay and stick it in my Sawtooth.
After packing away my little brothers sawtooth 400Mhz with 384mb RAM and an 8Mb ATI AGP graphics card and then unpacking it I've been having a problem. When starting the computer up the screen shows nothing at all I have tested to see if the screen is broken and it seems to be functional. I think the card itself might be broken? BTW, I'm using the VGA slot and not the DVI slot on the back. I have also removed and cleaned the card just incase that might've been the problem.
View 3 Replies View RelatedI have an iBook G4 1.07 GHz 30 gb 256 RAM with Panther. It was working fine until my HD got close to being full. Now I can't get it to boot past the Apple screen. It will either freeze there, or move on to the blue screen and freeze before the progress bar enters. I want to re-install Panther but I can't get any CD to boot during startup by holding "C", including the Panther OS CD, the Hardware Test CD, or the Tech Tool CD. I am able to boot to single user mode, where I type fsck -fy, and I recieve no errors with the hardware. I had this issue beore and my HD had to be replaced by Apple.
View 6 Replies View RelatedI recently upgraded my old Airport Extreme Base Station (looks like a lumpy cap) to a newer AirPort Extreme Base Station with dual-band support and 802.11n. I installed the software on my Macbook running Snow Leopard, created a new set up with new passwords, etc. The Macbook and a G4 12" rev A PowerBook running OS 10.3.9 connect fine, but a G4 500 GHz Sawtooth, running OS 10.3.9, with an original Airport card installed will not connect. Initially the new networks showed in the AirPort inverted triangle bars, but now the triangle is grey, and I can't get any connection with Internet Connect or the network diagnostic that comes with the OS. 2 out of three ain't bad, but I want all the computers to connect.
View 1 Replies View RelatedGot a Powerbook G4 with a "messed up" HD. Couldn't fix it, so got a firewire drive and ran a bunch of utilities from my newer intel iMac. Cloned the Powerbook's drive to a USB hard drive, did all repairs on the USB drive, formatted the Powerbook, cloned the USB drive BACK to the Powerbook, but it just gives me the flashing question mark when I try to boot.
What is REALLY weird is I can boot my iMac FROM THE CLONE ON THE USB DRIVE and it works fine.In Drive Genius the Powerbook drive (in TDM) shows as a single drive, but if I go to "Repartition" then it shows 3 smaller partitions on the drive; I believe they're called "Apple Free Space" or something like that (can't check right now, I'm running Repair on it AGAIN at the moment).
I feel like I'm missing something simple, like the machine just doesn't see one thing that tells it "Oh, yeah! There's an operating system on this drive!" I have tried partitioning from Drive Genius and Disk Utility. Have done clones back and forth with Drive Genius, Disk Utility, and Carbon Copy Cloner. Same results each time.
I can't get OSX to boot on the G3 when I reboot with the C button down it won't do anything no apple logo or anything. It's 10.4 and the cd version What am I doing wrong?
View 1 Replies View RelatedMy Powerbook g4 al 1GHZ won't boot up. I press the power button it chimes, i can hear the hardrive and fans spinning but the screen is black.
View 9 Replies View RelatedI'm trying to install Damn Small Linux on iMac G3,64MB ram and 333Mhz processor. The problem is that i'm not able to boot the cd. Under windows machine...it boot normally,but if i put it on G3 and hold 'C',it doesn't boot (but i think it try to read the cd becouse i see a small icon with "face"/"?" on the screen).
View 15 Replies View RelatedMy PowerBook G4 1.5Ghz won't boot up. It happened about a year ago when I first got my new MBP so I just let it sit. But I'd like to give it to a friend if I can get it to work. I've tried resetting the PMU by holding shift+control+option+power... waiting 5 seconds and powering on, but nothing happens. The battery appears to be functioning correctly. When the cable is in it lights up like normal and the battery indicators light up and are in full charge. I've taken the ram out and put it back in. Any other clues what I could try before bringing it in to Apple?
View 1 Replies View RelatedI have a usb thumb drive can I boot leopard from a usb?
View 2 Replies View RelatedMy trusty ol' powerbook might have finally met its match. I can not get it to boot into any mode. I've tried booting to the original discs ('C' while starting up); safe mode, single user mode, etc. I've reset the PMRAM (or whatever it's called) It seems perma stuck at the blue screen.
View 4 Replies View RelatedMy powerbook was working fine but i shut i down over night and when i turned it on the next morning it refused to boot. All i got was a grey screen with the folder icon which flash between a question mark and the finder icon.
View 8 Replies View RelatedI opened up Garageband, went into preferences to configure the audio for my peripheral audio device, and the computer and curser locked up, so I had to shut it down by pressing the power button for 4 seconds. I restarted the G4 and it would only boot up to a blue screen with the pointer curser, but would not finish loading anything on the desktop, no icons, no menu, nothing. I tried restarting repeatedly this way, but got the same result each time.
View 6 Replies View RelatedI was playing some old freeware games for Mac OS 9 and was playing lemmings when my Clamshell iBook just turned off and now I get the Blinking folder with question mark. I made a live CD of ubuntu where it's talking to the harddrive but the iBook won't boot to OS X so i am trying to figure why.
View 10 Replies View RelatedMy powerbook G4 keeps freezing whenever I try to start it - as limited as my Mac vocabulary is, the "spinny thing" that goes by during the "gray boot screen" with that there "Apple logo" stops and the entire process is frozen. Paper season is started here at school - and I hate click-clacking on the cheapo Dells in the computer lab.
View 14 Replies View RelatedMy friend just got a 800 Mhz iBook G3 from someone. I think it's the April 2003 model. It has a CD-ROM drive so I think it's that one. The iBook has Mac OS X 10.4 Tiger on it. The problem is that in normal boot, it hangs right before the "Starting Mac OS X" screen with the bar. The mouse pointer just stays in the corner. The computer can boot into Safe Boot. He tried reinstalling the OS with Archive And Install keeping the same settings but it still does it. Apparently he says that he had to boot into the Mac OS X Install Disc in safe mode by holding shift. Starting the computer holding Option and selecting the Install Disc caused the installer caused it to hang in the same way. He is currently doing another Archive And Install with the keep settings box unchecked and has yet to do an Erase And Install.
View 3 Replies View RelatedI have a G4 PowerMac that will not boot up. I power up the computer and it stalls on a grey screen with text prompting me to type <<boot>> if you wish to continue...or something like that. Does anyone have any advice on how I might troubleshoot this? The computer was working fine for a few days before this occured. It has been unused and sitting is storage for a while.
View 2 Replies View Relatedmy powerbook was playing up yesterday and i had to power off via the switch and now it wont boot, All i get is a grey screen no apple logo and no spinning dial, in stead i get a picture of a happy mac face and then a question mark and sometime not even that.
View 5 Replies View RelatedAssuming it's the HDD, which I already got a replacement. Can I take out the HDD and install it in an enclosure and run some sort of recovery software? I had alot of personal stuff as well as my portfolio work in there
View 2 Replies View Related