I have a bunch of macs in the house. I am trying to install Leopard on a 17" G5 imac but I can't get it to boot off my Leopard install CD (a dual-layer backup copy as the original cannot be located at the moment). The disk will mount under tiger, but will not boot, either from the internal DVD or an external drive.
Is there any good trick to do the install? I did an install onto an external USB drive that booted an intel iMac but that drive wouldn't boot the G5. Anyone have any tricks? I've never done target disk mode and don't think I have a firewire cable, but could get one if needed.
ive got a Imac 17inch 1.0ghz with 215mb ddr ram. anyways, as Sheepy suggested, i upgraded her to a nice speedy 500GB 7200 Sata drive and dropped 1.5gb ram into her...... but lets take a step back. when i got her, she was full of dust and had tiger on her.. no dramas, tiger is good. anyways, i wanted to do a reinstall of tiger, and so grabbed my tiger retail disk and started her up, no dramas there either, ran disk util, repartitioned (the old disk) and started to install. the install never finished and then it just rebooted after about 80% through... The reboot came to the disk flashing with the osx face and a question mark. I try a few more times, with the same result, and also with Leopard, also with the same result, but the leopard install actually tells me after about 80% that "Install failed" try again? anyways, so i think its a shagged optical drive. i have a few lying around and i need to get in there anyways to upgrade the hard drive. installing the HD and the new Optical drive went fine, all works well.. and while i was there also installed 500mb ddr400 stick in the main memory non user slot. close her up, checked the heatsink matchup spots and there dry as a nuns nasty.. theres no paste on them, but kinda like a pad.. (which isnt even sticky either) anyways, i stick em back together (without) cleaning the pad stuff nor with applying any paste and boot her up. I insert the leopard disk to istall and it all goes fine, i re-partition the newspeedy 7200rpm sata disk and start the install. and again.... gets to about 90% and reboots. flashing smily face with alternating question mark.
Now, my poor little G4 was just standing there. After a lot of fumbling around, restores, it finally has regained life, running Tiger etc.
Now, I wanted to install Leopard, see for myself what I would prefer, and it would allow to tether wireless internet connection through my iPhone to the G4. But I need Leopard for that, Tiger is too old.
So, after Googling, I found out that if I put my Intel into Target Disk mode, I could use it as external DVD reader, seeing my G4's reader is dead as dead can be.
I found a great deal on an eMac for the rest of my family to use. Before getting started, I wanted to reinstall Leopard using a disk image. Obviously with an eMac, I am not able to boot and install using a USB flash drive so I used an old iPod with a firewire connection and put the disk image on the iPod. The problem I am having is when I hold down the "option" key on startup, the iPod drive does not show up. Am I doing something wrong? To my understanding, I thought I could use an old iPod to install OSX
i attempted to install leopard with firewire through my mac mini, yet it get to the install menu and says: leopard cannot be installed on this machine. it is the two leopard discs that came with my mac mini intel c2d. I also have a powermac g3 i could run firewire out of if necessary. I dont know if it is the discs because i used the restore disc from a powermac g4 to upgrade this ibook to tiger.
is it possible to install Tiger on a iMac G3 with you iPod. Im in the process of selling it & i want to do some maintenance on it, so that its nice & speedy. Can i install Tiger using my Ipod Nano 2G? If so what is the process of going about doing so?
I recently purchased a G4 Mini (1.42Ghz I think) with 512Mb Ram for use as a second computer. It works fine with Tiger as it is, but I can get Leopard from my uni at a reduced cost, so.... I was wondering if anyone's been working with it on the lowest recommended Ram? Does it run OK? I'm loathed to take it apart unless I really have to as it's perfectly functional.
I have a PowerBook G4, 1.33 GHz, 512MB ram and I am having trouble installing leopard. I have backed up the hard drive and erased it for a clean install. Every time I go to install if freezes at "calculating estimated time remaining" and gives a kernel panic error. I am unable to check the panic log as the hard drive was erased. I have already repaired disk, reset pram etc.
I recently was given an 15 inch iMac G4 with 256 MB RAM and 800 MHz processor and was running OS X 10.3.9. I upgraded the RAM to 512 MB and installed Leopard using a firewire connection with my MacBook. I can boot from the MacBook Leopard but the iMac will not boot or seem to find the Hard Drive. I can see the Hard Drive on my MacBook with Leopard installed on it. All I get on my iMac is a "finder" with a question mark. Is there any suggestions or tips about how I can get my iMac to run properly using Leopard?
The iMac im using now has 10.4.11(tiger), however my brother has recently bought a MacBook. But what i was really wondering is if i am able to use the Leopard CD from the Macbook and install Leopard onto my iMac?(which is using Tiger) Is that possible or will i run into issues along the way? Edit:Also my iMac is using an Intel Processor(Core Duo)
I have accidentally wiped the hard drive of a mid 2011 imac 27" there was no install DVD provided for this machine and a retail Snow Leopard disk will not boot, apparently I need 10.6.8 and the retail disk is only 10.6.3 is there any solution to this dilemma?
I just installed Leopard on my iMac PPC G5. It calls for a shut down at the end of installation which it did. Now it won't power back on. Every time it gets to the starting chime, it shuts down. It was running fine before the installation of Leopard and now it's basically dead. I can't even get the disk out of the drive now and I'd like to. Is there a way to get it out?
I've searched for some time now and haven't seem to come up with a solution. I'm trying to Install leopard on my Imac, but every time I run into the "Software cannot be installed on this computer" message.
I just got my brand new 2.66ghz iMac in the mail. Wondering whether it is worth installing snow leopard before I painfully switch everything from my old computer to this one. I don't want to have to redo my entire system later.
I need to install snow leopard on intel imac that is already running lion. I have created new partition and try to boot off of Install Disk 10.6.4 but it never completely comes up all the way to start install.
I have just got an old 2004 G5 and thrown a brand new hard drive in it. When i tried to install leopard (which I'm told would be the best operating system to use) it comes up with a blank blue screen!
I have a 1Ghz PowerPC G4 iMac and want to delete everything and start again with Leopard. (it seems to be within the system reqs.) Problem is the DVD drive isn't functioning properly. It sees the OSX DVD but won't boot from it. Question - What's the best alternative method? Create a boot firewire disk?
So i just got this imac g5 and planned on putting leopard on it since it has 1.5gb of ram. So i plop the dvd in and it doesnt read, but it will read other dvds and cds what gives?
I have an iMac G5 17" with 2GHz PowerPC G5 processor , originally had 512 MB RAM and has been upgraded to 2Gb RAM. The HD has been erased apart from the Tiger OS. I assume there is now 1Gb RAM in each slot ... not sure if the original 512 MB was split between two slots or if it was all in one slot. Have been using OS Tiger 10.4 up until now.
Recently I bought a RETAIL edition of Leopard 10.5.1 to install ( the one with the big X on the front) but after 10 minutes of the installation got the message "Install Failed ... Source Media Disc damaged" . I previously tried another Leopard installation disc and got the same message. I think it's unlikely that both installation discs are damaged; they are both new and came from reputable sources. I can reinstall Tiger without any problems. I have tried erasing the HD volume using Disc Utilities at the initial install stage but still get the same message .
A colleague has now advised me there have been problems with some iMac G5 machines with upgraded RAM when trying to install Leopard ... the Leopard installation disc does not like upgraded RAM.
Before I try and source some RAM to the original spec. ie 512MB, and then try again with Leopard, can anyone advise me if it might be worth taking out just one of the existing 1 Gb RAM modules ( I assume there are two there, I dont know for sure because the upgrade was done by a Mac Repair Shop ) and then trying the Leopard Install with just 1Gb RAM ? Or do I need to go back to the original 512Mb module(s) ?
I recently was given an 15 inch iMac G4 with 256 MB RAM and 800 MHz processor and was running OS X 10.3.9. I upgraded the RAM to 512 MB and installed Leopard using a firewire connection with my MacBook. I can boot from the MacBook Leopard but the iMac will not boot or seem to find the Hard Drive. I can see the Hard Drive on my MacBook with Leopard installed on it. All I get on my iMac is a "finder" with a question mark.
I have a tower Mac Pro with Snow Leopard running on it.Unfortunately one of the software that I use doesn't have yet a Snow Leopard update. So I am thinking maybe I can install older version of Leopard on one of the internal drives (i have 3 additional internal drives), so I can boot my computer from either Leopard or Snow Leopard, depending on needs (i don't want to get rid of Snow Leopard).
I never installed OS X system before, so I am a bit scared.The internal drive is ready, I have the old Leopard on disks, what are the next steps to take?
I have downloaded 10.5.8 combo several times and cannot get it to install because the disc won't mount or the installation gets hung up after restart. My current os is 10.5.1, and I am trying to upgrade to snow leopard. This is on a dual core macbook pro.
Info: MacBook Pro (15-inch 2.4/2.2 GHz), Mac OS X (10.5.1)
i recently got a used tray loading iMac G3 with a wiped hard drive. When I boot from the OS 9 CD and try to install OS 9, I get errors telling me to update the firmware, but when I try to update the firmware, I get errors saying that it can't install anything because the CD is a locked volume and I can't boot from the hard drive. Is there a way to install OS 9 on this machine?
I have a PowerBook G4 which failed me a couple of months ago. The screen would just freeze. Recently, I've managed to wipe the hard disk and wanted to do a clean install using the restore disk provided but it keeps hanging mid way (installation wouldn't complete).
I remember hearing about it on a website, is there any rough tutorials to go about this? Don't ask me why I want to do it, my friend said it can't be done, and I just want to show him up. he also thinks macs are dumb, so hes not so smart in the brain.
Im'e trying to install the o/s on a G4 with a clean hard drive the drive's been wiped of data and that's all It has not been formatted The screen says select destination volume but is greyed out i can't select anything Is the problem the fact that the hard drive is not formatted This is my first mac so don't know what to do.
