PowerPC :: Installing Leopard / Tiger On Imac G4 1.0ghz
Nov 4, 2010
ive got a Imac 17inch 1.0ghz with 215mb ddr ram. anyways, as Sheepy suggested, i upgraded her to a nice speedy 500GB 7200 Sata drive and dropped 1.5gb ram into her...... but lets take a step back. when i got her, she was full of dust and had tiger on her.. no dramas, tiger is good. anyways, i wanted to do a reinstall of tiger, and so grabbed my tiger retail disk and started her up, no dramas there either, ran disk util, repartitioned (the old disk) and started to install. the install never finished and then it just rebooted after about 80% through... The reboot came to the disk flashing with the osx face and a question mark. I try a few more times, with the same result, and also with Leopard, also with the same result, but the leopard install actually tells me after about 80% that "Install failed" try again? anyways, so i think its a shagged optical drive. i have a few lying around and i need to get in there anyways to upgrade the hard drive. installing the HD and the new Optical drive went fine, all works well.. and while i was there also installed 500mb ddr400 stick in the main memory non user slot. close her up, checked the heatsink matchup spots and there dry as a nuns nasty.. theres no paste on them, but kinda like a pad.. (which isnt even sticky either) anyways, i stick em back together (without) cleaning the pad stuff nor with applying any paste and boot her up. I insert the leopard disk to istall and it all goes fine, i re-partition the newspeedy 7200rpm sata disk and start the install. and again.... gets to about 90% and reboots. flashing smily face with alternating question mark.
is it possible to install Tiger on a iMac G3 with you iPod. Im in the process of selling it & i want to do some maintenance on it, so that its nice & speedy. Can i install Tiger using my Ipod Nano 2G? If so what is the process of going about doing so?
I have an iMac G5 17" with 2GHz PowerPC G5 processor , originally had 512 MB RAM and has been upgraded to 2Gb RAM. The HD has been erased apart from the Tiger OS. I assume there is now 1Gb RAM in each slot ... not sure if the original 512 MB was split between two slots or if it was all in one slot. Have been using OS Tiger 10.4 up until now.
Recently I bought a RETAIL edition of Leopard 10.5.1 to install ( the one with the big X on the front) but after 10 minutes of the installation got the message "Install Failed ... Source Media Disc damaged" . I previously tried another Leopard installation disc and got the same message. I think it's unlikely that both installation discs are damaged; they are both new and came from reputable sources. I can reinstall Tiger without any problems. I have tried erasing the HD volume using Disc Utilities at the initial install stage but still get the same message .
A colleague has now advised me there have been problems with some iMac G5 machines with upgraded RAM when trying to install Leopard ... the Leopard installation disc does not like upgraded RAM.
Before I try and source some RAM to the original spec. ie 512MB, and then try again with Leopard, can anyone advise me if it might be worth taking out just one of the existing 1 Gb RAM modules ( I assume there are two there, I dont know for sure because the upgrade was done by a Mac Repair Shop ) and then trying the Leopard Install with just 1Gb RAM ? Or do I need to go back to the original 512Mb module(s) ?
I am looking to upgrade the current memory in my iMac. It has 512 (2x256) and it says it supports up to 1gb total. However, i have been searching all over this forum seeing if it is possible to have more. Like if I added a 1gb sodimm to get it to 1.2gb. I have seen very little on this as I have searched these threads. Also, is the upgrade in memory really going to help me out? I really notice the slowdown in iMovie. I have been watching the activity monitor and even though the cpu can get up to 100%, the free memory will be down to 4 mb. oh ya, I am running 10.3.9. When i update the os, with a clean install, will i see any improvements without additional memory? Or will i need more memory just to keep tiger or possibly leopard running good?
I have a bunch of macs in the house. I am trying to install Leopard on a 17" G5 imac but I can't get it to boot off my Leopard install CD (a dual-layer backup copy as the original cannot be located at the moment). The disk will mount under tiger, but will not boot, either from the internal DVD or an external drive.
Is there any good trick to do the install? I did an install onto an external USB drive that booted an intel iMac but that drive wouldn't boot the G5. Anyone have any tricks? I've never done target disk mode and don't think I have a firewire cable, but could get one if needed.
I have two macs(one is macbook, another one is G4 cube). On my G4 Cube OS 9.2 is running and it is up to date. (last firmware update installed) I want to install mac os x tiger on it but i can not. I tried almost everything but i couldn't install yet.
Firstly I downloaded tiger.dmg and burned into a dvd, then inserted to the Cube. It can read the DVD but couldn't run the tiger dmg file. so i could not install in this way.
Then i connect the macbook to my Cube via firewire and I inserted the installation dvd to the macbook but the result was same. cube can read the DVD but couldn't run the tiger dmg file.
Then I changed the host and target. I saw G4's harddisk as an external harddisk on my macbook's screen and i found the OSInstall.mpkg after I mounted Tiger dmg file on desktop. I choosed as installation destination G4's harddisk and installed the tiger on it. Then i open the Cube and I opened startup disc on os9 to choose os x as startup system. Though Tiger's system files are on the G4's harddisk there is no choise as os x in the startup disc menu so i couldn't start tiger.
I have a G3 iBook, 600MHz, 2 USB slots, 1 firewire slot, DVD ROM/CDRW with 640Mb. I bought a Tiger DVD which on the front says: "Mac OS X Tiger. Includes Xcode 2. Install DVD. Version 10.4.6." It came as new, inside a Mac OS X box (no grey installation discs - just 1 black DVD). But...it won't install on my iBook. In fact, it won't even mount on my desktop! I've tried holding "C" on startup but that won't help. Incidentally, I can't repair permissions (I just get "No valid packages (-9997)") but that seems to be the only thing going on with my Mac! Any ideas to get this show on the road?
I've got an old Ibook G4 with Panther and Ilife installed - I want to update to Tiger but keep Ilife - I have a retail copy of Tiger that doesn't include Ilife... What is the cleanest way for me to install Tiger and keep Ilife ?
I recently recived a iBook G3, Specs are 600Mhz, 635Mb Ram, 20Gb HDD. I go to install OS X Tiger and it either shows "You Have To Restart Your Computer......) or a System Failure: CPU=0 (Unaligned Stack) error. This is as it boots the CD for install. When it spits the error code in the background is the apple boot screen
Now, my poor little G4 was just standing there. After a lot of fumbling around, restores, it finally has regained life, running Tiger etc.
Now, I wanted to install Leopard, see for myself what I would prefer, and it would allow to tether wireless internet connection through my iPhone to the G4. But I need Leopard for that, Tiger is too old.
So, after Googling, I found out that if I put my Intel into Target Disk mode, I could use it as external DVD reader, seeing my G4's reader is dead as dead can be.
I'm wondering if it is possible to install different MAC OS versions (for example, having Leopard and Tiger OS X) on the same computer, as you usually do with different versions of Windows just making some partitions. Is it possible? If yes... how?
I am having trouble installing Leopard over my 10.4 Tiger Mac, I am using "grey faced" dvd's that came with my 10.5 Leopard Macbook, to install Leopard on my Mac, but whenever it starts up the process of installing it, it gives me an error " Mac OS X can not be installed on this computer" It gives me 2 options, to restart or "ok", if i choose "OK" i can roam about in disk utility, password reset etc etc as you would" I am wondering if this is a computer/disk problem, or will I just need to go buy snow leopard from a retailer?
I recently acquired an original iMac G3 from my Uncle. I put a 80GB PATA drive in there, and installed OS9 without any hitches (apart from the fact that it doesn't recognise the HD because I think I have the jumpers wrong, it still boots eventually though). Anyways to my question, does this version of iMac support OSX? I am hoping to install Tiger onto it, regardless of the speed that the machine will be. I had a Graphite iMac so I'm used to slow speeds baha. I'm guessing the main problem would be in regards to the CD drive, it isn't a DVD drive.
I have a macbook pro 13".. the HD crashed and i had to send it out for recovery (the platter was f'd up) and the optical drive stopped working.
i have a thingy i use where i pllug in the internal HD and it becomes a USB on my imac... can i run Tiger and install it to that specific HD and format it as well? then when i plug the HD back into the macbook it will work?
I recently did some work to a 15" 700mhz G4 iMac I got as a gift. I put in a new hard drive, DVD burner and an airport card. Now I'm at the point where I need to install Tiger. I have the original owner's disks, but the only form of input I have for the iMac is an old USB keyboard which was used for the PlayStation 2.
I tested the keyboard on my MacBook and found that it works fine, but only after I had to run a test to recognize what kind it was. I'm pretty sure that since I can't plug and play with this keyboard (without running a test) I won't be able to use it to install Tiger.
So this is where I'm stuck. Is my problem as easy to fix as borrowing a more modern, made-for-a-computer keyboard? And if so, does it have to be from Apple, or will a Logitech or Dell work nicely?
I had some great last night regarding the need to get a "Black" retail disk in order to install Tiger onto my iMac, I have searched on ebay and have found some grey disks which read - "For Mac Computers" on the left hand side. In small print at the bottom they have 'Mac OS version 10.4.10, AHT version 3a133, disc version 1.0, 2z691-6089-A'
I am still on Tiger, mainly because I really like its feel and simplicity as compared to Leopard or Snow Leopard, and its been fine up until recently because it did everything I needed. Recently, I've been encountering more frequently apps that I want to try but that are only available on 10.5+.I have a Leopard CPU Drop-in Disk, and am thinking about upgrading soon, however, I am using a 120 GB HDD that is getting close to being full, and I am concerned that installing a new OS would eat up some of that precious available HDD spaceDoes anyone know what the size difference is between Tiger and Leopard or between Tiger and Snow Leopard? If it's more than 4 GB, I don't think it is really worth it to me.
Further to one of my previous questions i have now managed to get hold of OSX tiger for my Imac G4 800mhz superdrive. However no matter what I try I cannot get this to install. If I go through custom instal it checks my disk and then comes up with a notice saying "mail cannot be intalled on this computer - intallation not possible" or something along these lines. I have also tried restarting while holding down the command button but the 10.4 disk does not appear. I have completely wiped my harddrive and reinstalled my original osx 10.3 and even taken out the airport card and additional ram memory card which i thought was causing the problem.
I have a 17" iMac G4 that I was rung Tiger with, then I installed Leopard 10.5. I use this as a second computer. All is fine except that my Epson scanner does not work with 10.5. I've tried the latest drivers. I'd like to reinstall Tiger. I used the 10.5 disc to reformat the drive and start from square one. When I boot from my original Tiger disc it starts opening it's windows, but when I get to the point where I can choose Install or use Disk Utility to reformat from the Tiger disc, all windows freeze and I need to hard reboot from the power switch. Am I correct to assume that 10.5 won't let 10.4 to reinstall. Is this correct?
"it is possible to completely erase a hard drive and install Snow Leopard without a pre-existing operating system in place, enabling users to bypass the possible headaches of an upgrade and go with a clean install instead. Wired said many users upgrading from Tiger should probably consider backing up their files from Tiger and doing a clean install instead."
I don't have an external harddrive. What other backup options do I have?
I have an Emac. I'm angry because the Ipods don't work with Panther. I don't think it's worth upgrading the OS, but if I was, which one would I want? Mine is 1Ghz and 768 MB so it meets the requirements for 10.5, but would it run better with 10.4?
I've got a ibook 1.2 ghz w/ 1.25 gigs of ram. I'm going to be using it for school. Just some word processing, email/internet, and music. It came with panther and it has the latest updates.. Is it worth it to get Tiger for it? Will I notice a huge difference? Things are alright now, but I'm used to my MBP zipping through everything. I know it won't ever be as zippy as the MBP, but will Tiger make a huge difference?
I recently bought an iBook with a 1.33 GHz processor, 1 GB of ram, and a 60 GB hard drive. It's still 3 to 8 days until it gets delivered, but I was doing some thinking, and couldn't decide between Tiger and Leopard. It comes with Tiger and iLife (not sure what version of iLife). My brother has a Leopard install disk that he says he'll lend me if I want to install it. I am leaning toward Leopard, but only because it has a nicer GUI, in my opinion at least. I'll probably use Tiger on it for a week before deciding to whether upgrade or not.
I've got a flat panel G4 iMac, currently running 10.3.9. I'm having ongoing problems: frequent kernel panics, weird things happening to the display (display breaks up into a jumble of lines on occasion). I've done the usual troubleshooting: disk utility, apple hardware test, reboot in Safe. I want to try reinstalling the OS to see if this helps.
Problem: I don't have the install discs for OS 10.3.9 - about a year ago the logic board was replaced and I had the service swap in a new hard drive at that time and they loaded 10.3.9 when they did this. I don't want to buy 10.4 at this point - with Leopard coming out soon from what I understand, also want to make sure I can get the computer running properly again before I throw any more money at it. I've tried using borrowed discs to install 10.4, but I keep getting a message stating: "you cannot install this software on this computer". This has happened with 3 different borrowed install discs. Two of the borrowed discs were for iBooks, one was for a G5 iMac.
so i want to install tiger on my G3 600 mhz 256 mb RAM imac that has no dvd drive.i looked around the net and found that apple used to accept tiger DVD's and exchange them for CD's for a 10$ fee but thats no longer the case....
i also found that i could install tiger from another mac with a DVD drive using firewire disk mode...so i looked around my things and found an old firewire cable and hooked both machines up (imac and my mbp) and restarted the imac holding down the t key and so then the firewire symbol shows up on the imacs screen...well from what i understand the imac's HD is supposed to show up on my mbp desktop...this never happens.And ive tried it multiple times...so i dont know what the problem is..and ive tried it using OS 9 and 10.0 the OS's the machine came with..
I might be getting a iMac G3 (for surfing and maybe itunes) and I was wondering if I should put tiger or panther on it? I had tiger on my iMac G4 before it died and I loved it. I was used to leopard before though (my imac G6). I don't know the processors or anything yet... but since I'm getting two of them for free I'm not really complaining. How much iMac G3 suck. I think they are adorable
A friend of mine gave me her old iBook G4 so I can fix it. Something was wrong with it (half the applications are missing, spotlight reindexes every time it restarts etc). So I'm just gonna reinstall everything from the ground up. My question is though, should I install Tiger again or would Leopard be better? The only thing I am afraid of is that Leopard would slow down the iBook since it's an older Laptop. Here are the specs:
