I have an iMac G5 17" with 2GHz PowerPC G5 processor , originally had 512 MB RAM and has been upgraded to 2Gb RAM. The HD has been erased apart from the Tiger OS. I assume there is now 1Gb RAM in each slot ... not sure if the original 512 MB was split between two slots or if it was all in one slot. Have been using OS Tiger 10.4 up until now.
Recently I bought a RETAIL edition of Leopard 10.5.1 to install ( the one with the big X on the front) but after 10 minutes of the installation got the message "Install Failed ... Source Media Disc damaged" . I previously tried another Leopard installation disc and got the same message. I think it's unlikely that both installation discs are damaged; they are both new and came from reputable sources. I can reinstall Tiger without any problems. I have tried erasing the HD volume using Disc Utilities at the initial install stage but still get the same message .
A colleague has now advised me there have been problems with some iMac G5 machines with upgraded RAM when trying to install Leopard ... the Leopard installation disc does not like upgraded RAM.
Before I try and source some RAM to the original spec. ie 512MB, and then try again with Leopard, can anyone advise me if it might be worth taking out just one of the existing 1 Gb RAM modules ( I assume there are two there, I dont know for sure because the upgrade was done by a Mac Repair Shop ) and then trying the Leopard Install with just 1Gb RAM ? Or do I need to go back to the original 512Mb module(s) ?
A friend of mine gave me her old iBook G4 so I can fix it. Something was wrong with it (half the applications are missing, spotlight reindexes every time it restarts etc). So I'm just gonna reinstall everything from the ground up. My question is though, should I install Tiger again or would Leopard be better? The only thing I am afraid of is that Leopard would slow down the iBook since it's an older Laptop. Here are the specs:
ive got a Imac 17inch 1.0ghz with 215mb ddr ram. anyways, as Sheepy suggested, i upgraded her to a nice speedy 500GB 7200 Sata drive and dropped 1.5gb ram into her...... but lets take a step back. when i got her, she was full of dust and had tiger on her.. no dramas, tiger is good. anyways, i wanted to do a reinstall of tiger, and so grabbed my tiger retail disk and started her up, no dramas there either, ran disk util, repartitioned (the old disk) and started to install. the install never finished and then it just rebooted after about 80% through... The reboot came to the disk flashing with the osx face and a question mark. I try a few more times, with the same result, and also with Leopard, also with the same result, but the leopard install actually tells me after about 80% that "Install failed" try again? anyways, so i think its a shagged optical drive. i have a few lying around and i need to get in there anyways to upgrade the hard drive. installing the HD and the new Optical drive went fine, all works well.. and while i was there also installed 500mb ddr400 stick in the main memory non user slot. close her up, checked the heatsink matchup spots and there dry as a nuns nasty.. theres no paste on them, but kinda like a pad.. (which isnt even sticky either) anyways, i stick em back together (without) cleaning the pad stuff nor with applying any paste and boot her up. I insert the leopard disk to istall and it all goes fine, i re-partition the newspeedy 7200rpm sata disk and start the install. and again.... gets to about 90% and reboots. flashing smily face with alternating question mark.
It might be possible to use the $29 disc but is is legal?:
"The actual 10.6 EULA:
C. Leopard Upgrade Licenses. If you have purchased an Upgrade for Mac OS X Leopard license, then subject to the terms and conditions of this License, you are granted a limited non-exclusive license to install, use and run one (1) copy of the Apple Software on a single Apple-branded computer as long as that computer has a properly licensed copy of Mac OS X Leopard already installed on it. If you have purchased a Family Pack Upgrade for Mac OS X Leopard license, then subject to the terms and conditions of this License, you are granted a limited non-exclusive license to install, use and run one (1) copy of the Apple Software on up to a maximum of five (5) Apple-branded computers at a time as long as those computers are located in the same household (as defined above), are used by persons who occupy that same household, and each such computer has a properly licensed copy of Mac OS X Leopard already installed on it. The Family Pack Upgrade for Mac OS X Leopard License does not extend to business or commercial users.to the terms and conditions of this License, you are granted a limited non-exclusive license to install, use and run one (1) copy of the Apple Software on up to a maximum of five (5) Apple-branded computers at a time as long as those computers are located in the same household (as defined above), are used by persons who occupy that same household, and each such computer has a properly licensed copy of Mac OS X Leopard already installed on it. The Family Pack Upgrade for Mac OS X Leopard License does not extend to business or commercial users.
I've got two Macs: one Tiger (iLife '06), and one Leopard (iLife '08) and I would like to upgrade both to Snow Leopard. I'm in the UK.I need help finding the best price/capability compromiseI have looked at the prices for doing this and come up with the following options:Most expensive optionBuy the 5-user Mac Box Set (Including OS X Snow Leopard, iLife 09, iWork 09) for 179This way I've got both machines running the latest everything.Next OptionBuy the Single User Leopard box set (including iLife/iWork 09) to upgrade the Mini to Leopard (?108.34) then buy the Snow Leopard family upgrade box to upgrade both machines to Snow Leopard (?39), total ?147.34. This way I have iLife/iWork 09 on the MacMini but not the MacBook.
Cheapest OptionBuy the Single User Leopard disc to upgrade the Mini to Leopard (?68.99) then buy the Snow Leopard family upgrade box to upgrade both machines to Snow Leopard (?39), total ?107.99.
Posting for a friend who has just purchased Snow Leopard Box Set and wants to upgrade from Tiger. She was half way through the installation when she thought that Snow Leopard had not asked her to back up and she cancelled the installation half way through (not sure how, think she just turned off her Mac). She turned it back on but the only option it is giving her is too continue with the installation of Snow Leopard.
What she wants to know is will the erase all her data on her hard drive, or will she still have her files located in Documents/ Downloads etc when the installation is complete. I know when I upgraded from Leopard all these files were still present, I'm not so sure if it is the same with Tiger. Shes really worried about this as she has some valuable files in there.
Is there anybody that has gone from Tiger to Snow Leopard and did this as an upgrade? Did all your music and pictures remain on your HD? Is it even possible to do it this way?
When I put my snow leopard disc in my computer, it has 1 option which says: Install Mac OSX and if I press that it says, press continue to restart your computer and installation will begin (or something like that). It's not clear to me if it's gonna erase my harddrive or not.
I've scoured the internet and haven't come across a definite answer yet for why I would not be able to put 2x2GB ram modules into my Rev A G5 iMac. I've looked at the developer architecture guide from apple and it says nothing as to why a larger module won't work. [URL]. I guess I am just looking to understand where the limitation exists, is it hardware not being able to address the extra RAM or something else. I've also been unable to dig up much more info on the U3L memory bus to see if thats where the problem might be. I'm thinking that at the time 2gb modules were uncommon or not made so there was no reason to include them, but now its only a little more than the 1gb ones.
I have an Emac. I'm angry because the Ipods don't work with Panther. I don't think it's worth upgrading the OS, but if I was, which one would I want? Mine is 1Ghz and 768 MB so it meets the requirements for 10.5, but would it run better with 10.4?
I've got a ibook 1.2 ghz w/ 1.25 gigs of ram. I'm going to be using it for school. Just some word processing, email/internet, and music. It came with panther and it has the latest updates.. Is it worth it to get Tiger for it? Will I notice a huge difference? Things are alright now, but I'm used to my MBP zipping through everything. I know it won't ever be as zippy as the MBP, but will Tiger make a huge difference?
I recently bought an iBook with a 1.33 GHz processor, 1 GB of ram, and a 60 GB hard drive. It's still 3 to 8 days until it gets delivered, but I was doing some thinking, and couldn't decide between Tiger and Leopard. It comes with Tiger and iLife (not sure what version of iLife). My brother has a Leopard install disk that he says he'll lend me if I want to install it. I am leaning toward Leopard, but only because it has a nicer GUI, in my opinion at least. I'll probably use Tiger on it for a week before deciding to whether upgrade or not.
is it possible to install Tiger on a iMac G3 with you iPod. Im in the process of selling it & i want to do some maintenance on it, so that its nice & speedy. Can i install Tiger using my Ipod Nano 2G? If so what is the process of going about doing so?
I've got a flat panel G4 iMac, currently running 10.3.9. I'm having ongoing problems: frequent kernel panics, weird things happening to the display (display breaks up into a jumble of lines on occasion). I've done the usual troubleshooting: disk utility, apple hardware test, reboot in Safe. I want to try reinstalling the OS to see if this helps.
Problem: I don't have the install discs for OS 10.3.9 - about a year ago the logic board was replaced and I had the service swap in a new hard drive at that time and they loaded 10.3.9 when they did this. I don't want to buy 10.4 at this point - with Leopard coming out soon from what I understand, also want to make sure I can get the computer running properly again before I throw any more money at it. I've tried using borrowed discs to install 10.4, but I keep getting a message stating: "you cannot install this software on this computer". This has happened with 3 different borrowed install discs. Two of the borrowed discs were for iBooks, one was for a G5 iMac.
so i want to install tiger on my G3 600 mhz 256 mb RAM imac that has no dvd drive.i looked around the net and found that apple used to accept tiger DVD's and exchange them for CD's for a 10$ fee but thats no longer the case....
i also found that i could install tiger from another mac with a DVD drive using firewire disk mode...so i looked around my things and found an old firewire cable and hooked both machines up (imac and my mbp) and restarted the imac holding down the t key and so then the firewire symbol shows up on the imacs screen...well from what i understand the imac's HD is supposed to show up on my mbp desktop...this never happens.And ive tried it multiple times...so i dont know what the problem is..and ive tried it using OS 9 and 10.0 the OS's the machine came with..
I might be getting a iMac G3 (for surfing and maybe itunes) and I was wondering if I should put tiger or panther on it? I had tiger on my iMac G4 before it died and I loved it. I was used to leopard before though (my imac G6). I don't know the processors or anything yet... but since I'm getting two of them for free I'm not really complaining. How much iMac G3 suck. I think they are adorable
I have an old imac G3 /500 mhz graphite from my old work sitting around just for my little one to play cd games. I use PC now to do my emailing and net-surfing, but gotta admit I used to love this machine, and though it's old it still looks cool. I didn't get around to connet it to go on-line, because of compatibility problem with PC(main cable modem is connected to a PC) but now thinking about upgrading it to go on-line for my kids to use. It has OS 9.0.4, 128MB of RAM with speed of 500 mhz w/front slot loading. I'm not computer savvy and don't know much about it, but was told before that system has to be upgraded to OS 9.1 or later first, in order for wireless card to be installed. Can anyone help me with exactly what I need to go on-line with this imac? since it's going to be mainly for my kids, I do not plan to purchase any additional application software, but willing to spend some to upgrade system, memory, and on wireless card. I'm thinking I might not even need newest system as long as it can go on-line, but which OS system(or should go higher?) would make more sense? How much more memory?Is it really possible to install a wireless card on this machine? Would there be a problem because main cable is connected to a PC in which wireless router is installed(for another window laptop)? Or is it even worth trying? Appreciate any advice you computer genius out there could give me.
if it was possible to swap out the first intel processors with the newer ones the imacs are coming with. i found this info and mainly looks just as tricky as open heart surgery to risk my imac doing, and thats just replacing the processor itself.
I recently upgraded my powermac G5 dual 2.5ghz from tiger to leopard and for some reason it is no longer showing "dual" under "about this mac." In addition, under "more info" where it says number of cpu's it only says "1." Is there any way to fix this- is there a way to look in the bios and confirm that both processors are working correctly?
I got a G4 iMac with a 1ghz powerPC and 512MB ram for Christmas - it came with Leopard.
It's not horrible slow but you can tell it's trudging along quite choppily at times (when I try to load anything in flash or youtube it can't handle it).
Would I be better off going to Tiger? I've never used Tiger before - would my experience on Tiger be horrible compared to Leopard?
I have an imac g5 2.1ghz (isight version). The previous hdd completely broke, so with great struggle I managed to open it up and put in a 500gb hdd, I'm now looking to fresh install OS x. I put tiger in the imac and hold 'c', it boots to a grey screen with a folder and an exclamation mark. I put the disk in and hold the option key, it goes to a menu where an hour glass appears for about 3minutes before my tiger install disk is found. The install disk has an image of a disk with a small cross in the bottom right corner (i thought it was supposed to have an image of cd itself, but at least its recognized) I click the cd to install and it goes to a white screen with the apple logo, after a brief minute, a spinny wheel appears and spins for about 3-5minutes.
The apple logo then changes to a cancel or stop sign but the spinny wheel is still spinning below...I left it for about 40minutes and it didnt go any further. I've tried several times with the same result, I've also created a bootable usb with tiger on it and had the same result after using a command on the open firmware comand line to boot the usb, a friend tried to create a usb with leopard on it, but after trying to boot it..i get a message saying "Load-size is too small" Here are some pictures (click the tabs to see all 4) [URL]
I just bought a used iMac g4 with the following specs: 1.25 ghz, 160 gb HD, 1 gb of ram, with a 20" screen (USB 2.0). It has OS X 10.3.9 installed. I have retail copies of tiger and leopard. The problem is that I can't get either to install. When i load the disk, the computer restarts, but then returns back to home screen. I've tried holding down "c", but that does nothing for me. I've also gone to start up disk in utilities, but all that is listed on there is my G4 hard drive and "network". The superdrive isn't listed on there. I know the super drive works; i've used it several times and i used it to open up the install disk. What am I doing wrong.
I'm finally ready to upgrade from my Tiger OS to the new Lion. I have the disc, from Apple, to upgrade first to Snow Leopard and from there I'll immediately download Lion. I'm assuming there's no reason, and it's best not to open any files while I'm in Snow Leopard.
I have my Home folder backed up to an external hard drive. Is there anything else I should know or be aware of? Is there any special way to do this? I read something once about maybe doing a "clean install" of the new OS (Snow Leopard or Lion?). I don't really know what that is. Will that be necessary?
Info: iMac7,1 2.4 GHz; 2GB, Mac OS X (10.4.11), Tiger iLife '08 Alesis IO|14 FW Interface
I know this concerns an older machine, but I was hoping to get some solid advice on this subject. I have retail copies of both Tiger and Leopard for my G4, and my OWC order just came in the mail, and after tearing it down, cleaning it up, and throwing a new 160Gb drive and 1Gb of memory into it, the machine is feeling extremely responsive under Tiger. My question is thus: everyone seems to think Tiger's days are numbered, which I can understand when you consider it's age. But how numbered are numbered? Safari and iTunes are still supported up to the current versions, Camino is still supported on 10.4 so when Firefox drops Tiger support I'm not without a Gecko based browser, and the other software I plan to use on this machine (iLife 06, OpenOffice, JDarkRoom and some old games, primarily) are all still good for Tiger.
My primary concern stems from the web browser issue, but more importantly, internet security on this machine. It's on a wired connection behind an AirPort Extreme so I don't know how worried I need to be, but last I checked security updates are not coming down for Tiger anymore from Apple, thus would the iMac become a potential target running Tiger? I don't want to be running bare arsed to the wind, if you'll pardon the expression. So I was hoping someone with a better understanding of software security could explain differences between Tiger and Leopard and wether or not that's a huge deal. I'm tempted to stick with Tiger, because now that the upgrades are in, it's lightning fast. Almost as fast as the MacBook fast, which is impressive from an eight year old machine.
I am attempting to load tiger onto my 12 inch PowerBook G4. The installation cd runs up to the first part when it asks you to restart. Then after the restart it up and comes up with a error message 'unable to find driver for this platform: "PowerBook6,4".' This is not the complete message as it is to long to type out. I have tried every thing I can think of fsck, repairing permissions, removing an after market ram and I have tried lots else.
I was wondering how would I do a system restore on my Leopard upgraded (from a Tiger OS) iMac? I have done several google searches and i keep getting various answers (which there are different ways but I just want to restore my iMac to factory setting) Would I use my leopard or tiger disk, and how would I go about doing a system restore? What I wanted to do was do a system restore on my mac and upgrade to Snow Leopard. There are alot of scattered unimportant photos, movies, and games on my mac and it feels like a system restore would save me alot of time.
