The new firmware for the thunderbolt display now is making the screen go black all the time. How do I uninstall this update?Â
Info:
MacBook Pro with Retina display, thunderbolt display firmware
Thunderbolt Display Firmware Update 1.2 will not install. I've opened the clamshell on my MacBook Air and the update still fails while the Thunderbolt display is connected to the Air
Info:
MacBook Air, iOS 8.1.1
About half a year ago I got a Macbook Air, and a Thuderbolt monitor. Then I installed Windows 7 64-bit on it. Everything worked fine until recently the Thunderbolt monitor started to go black during Windows startup without any particular reason. Using OS/X the monitor works fine. I already scanned for malware and viruses but cannot fine any. Windows restore refuses to work? I also tried several different boot options, installed latest drivers, reinstalled bootcamp drivers but no luck so far. Â
Info:
MacBook Air, Windows7, bootcamp dual boot
I came back from work to wake up my iMac. It made the noise but the screen stayed black. I tried restarting by holding the power button- I can hear it start and the chime but still have a black screen. I tried resetting the pram, and unplugging the cord but I still get a black screen. I can hear the chime though; I'm not sure if that means anything. I just had the hard drive replaced in February so I hope it's not that. just wanted to clarify that when I restart, I get the chime but the screen stays black- I don't get to the grey screen. So I'm assuming right now that my display may be shot?
Info:
iMac (20-inch Mid 2007), Mac OS X (10.5.8)
I've installed Thunderbolt firmware update 2.1. Now, When I've started again my computer, Macbook Pro with retina display and Macbook Air doesn't work. I've tried install this update with Snow Leopard and Lion system.
View 2 Replies View RelatedI recently downloaded a firmware update from Apple both as a stand-alone software and using software update but everytime I restart, my computer makes one loud beeping sound and tries to boot three or four times unsuccessfully and maybe on the fifth or fourth, it finally comes on. When I go through software update after this, it still shows the same firmware and same version of it as an update I haven't downloaded. And another thing it freezes a lot since I downloaded this firmware update. This is how it shows on software update; Macbook Pro EFI Firmware Update version 2.7 size: 4.1 MB.
Info:
MacBook Pro, Mac OS X (10.7.3), 13 inches 2.3 GHz processor speed.
I have a Mac Pro (Early 2008) running on 10.5.8 OSX with apple 20" display and 16G RAM.
Initially started with my MACPRO not waking up from sleep and has to force the shut down with power button. Finally realised it was due to my Epson scanner connected via USB...
The main issues now is with the display, black screen on startup. I can still control the volume and disk eject/close, just no display. Force shut down with power button numerous time but futile. Finally solved it with SMC reset.
it becomes an on and off issues... and continuously I solved it with SMC reset.... sometimes needed 2 or 3 resets to get it to work,and finally for the past few days... SMC reset can't solve it either... no display on startup, and same thing I can control the volume and disk eject/close. Have tried my monitor on other mac and it worked fine.
Now this is strange. if I let the mac cool off totally,after a SMC reset. the display will comes up fine...
I was browsing the internet, not doing anything major, put the computer to sleep, came back 10 minutes later... black screen. I messed with it for an hour or so and determined that the video card went bad (I'm guessing. It's a mid 2007 macbook pro with the nvidia geforce 8600m. My secondary monitor remains black as well). In the midst of totally freaking out, I decided to activate the voiceover utility, enable screen sharing (after figuring out a slew of keyboard commands I didn't know about), and logged in from my girlfriends computer.
I immediately closed all the windows and applications that I had inadvertently opened during the blind wtf session, and opened up system profiler to see if it is recognizing a video card. Well, it is! It's listing the video card as a GMA x3100! Is there a secondary card in there? Cause if there is, it's not working either. Or is that just a default they would put in if it doesn't recognize a video card? Doesn't seem likely. Or, because I'm using screen sharing, is it picking up my girlfriends card? It's not, because she's using a GMA 950. Maybe it's splitting the difference?
Ive got a hd cinema display 23 inch wich stopped working last week.The power led is on, not giving a code or anything.I'm not affraid to open it, it is allready. But i dont see obvious black smoked parts
When I shine on the screen with a flashlight or something, I dont see images. so I dont think its the inverter.Was hoping someone here might know more?Perhaps logic board? not sure what that does btw
I have a core i7 MBP with the high res display, and when the display is showing black, a horizontal green line appears on the screen. It is only visible when the screen is showing black or another very very dark color, and the line is not visible with the screen off. It isnt something on the screen, as rubbing it does not affect it at all. I cannot post a screenshot of it, because it does not appear in the screenshot (it does on my screen, because the line is there physically, but on other monitors it is not visible).
View 3 Replies View RelatedI've had my mac for about three years now and everything was working fine. After I installed lion, I notice that this started to happen. I don't lose any of my information though when it does that. It just goes into a sleep mode I guess? Anyways, is this a feature from the lion update? Something standard?
Info:
MacBook Pro, iOS 5.1
if i Connect my Macbook air to the apple Cinema Display through thunderbolt is the air getting power supply through the Display?
View 1 Replies View RelatedSo I've got my MBP that I've had for about 4 months, the thing is. It just recently started to have screen flickering issues. I'll be sitting doing w/e as usual and all of a sudden the display goes dark, almost black, for a second, then comes back up again. I have yet to find any trend in when this is happening, but it is definitely happening on battery as well as plugged in, but it seems to be getting worse.any one have any idea what this could be, something I can fix on my own, or should I take it in?
View 7 Replies View RelatedFor the past few weeks it has been going to a black screen when trying to wake it up from sleep. Either I've put it through too much work lately editing all these photos and its really tired. So, often it wakes up normally and functions fine, well, not really. It is seemingly very slow. It requires a lot of time (more than before) to open up a program or it gives me the "spinning wheel of death" when trying to go to a different page on the internet or open up a folder on my desktop. Amongst other things that require it to think. So It's just a lot slower in general than before.
View 3 Replies View RelatedMy images on my screen are like in black and white.
Info:
MacBook Pro
Black screen on my iMac, how can I get it back to log in screen?
Info:
iMac
I use MBP (late 2011). I find the hunderbolt port to be similar to the mini-display port of older mac. I wish to have another display, but not ready to spend $999 over a thunderbolt display from mac. So would like to know if a Mini-diaplay port converter from apple would help me connect a exernal display via the thunderbolt port?
Info:
MacBook Pro, Mac OS X (10.7.4)
Today, I bought a vga adapter for my unibody macbook and it is not working. I hooked it on a 22 inch Samsung 225MW screen and it the screen shows a message "check your cable (PC)".
View 7 Replies View RelatedI have a MacBook Pro (13'', Early 2011) & iMac (21.5", Mid 2011) using a Thunderbolt Cable to Target Display. Everything was working find and I could Command F2 to Target Display as expected.However, about a week about this stopped working. Now when I try to Target Display the iMac goes to a Black screen (like it's switching to Target Display) and the MacBook Pro does nothing. The iMac will be at the Black screen until I Command F2 again (or disconnect the Thunderbolt Cable), then the iMac goes back to the normal display. I have tried another Thunderbolt cable with no luck. I have perform all software updates on both machines (now both running 10.7.3) and fixed Disk Permissions. I have also found that restarting my MacBook Pro allows this to function as excepected (Command F2, Blue Flashing Screen, Target Display on the iMac). However, this is not an ideal situation since having to restart my computer is time consuming. Â
View 8 Replies View RelatedI have a early 2011 MacBook Pro 13" running the latest version of Lion. I have been using my MacBook with an external monitor since I brought it in 2011 and have had no problems with connecting it to my external monitor. Connected via mini display port DVI adapter and a DVI cable to a Philips monitor.
Two days ago when I plugged the MacBook back in to the monitor I connected and but now only displays a black screen, I can move the mouse off the MacBook screen and over to the external monitor and back but it is not displayed on the monitor. I have tried connecting other devices to the monitor and they work fine.
Info:
MacBook Pro (13-inch Early 2011), Mac OS X (10.7.4)
my macbook air 13 display only black screen and pointer when wake up from sleep. its not frequently happen. to become normal it take 10-15 sec, is it hardware problem or software problem?
Info:
MacBook Air, OS X Mavericks (10.9.4)
Macbook pro 2014 only had it for about 2 months but recently about three weeks ago the display has been flicking to a black screen but has gradually been increasing and it now happens every two minutes - just randomly goes black for about 5 or 10 seconds and sometimes goes back to home screen but sometimes goes to log in screen, It interferes with me trying to do my work when this happens so frequently
Info:
MacBook Air, iOS 4.3.3, Transferring from Windows XP
So for the first time in over a year since I purchased it, my iMac crashed twice.The first time was this morning, i went to do something and the screen went black, and my secondary display got black and white lines. I had to restart. And the boot screen with the apple logo hung around for a while.
Then, later on the screen went whacky after trying to wake it from sleep (not full sleep just display sleep) and had a bunch of moving lines and then I couldn't see anything. So luckily I got a picture. After restart, it seems fine.I'll call apple care in the morning, but thought i'd try my luck here.
I have a 2 month old 13" MBP which I absolutely love. The only hitch is that there is an oddity when connected to my Dell 2008wfp display. It only happens when I wake the MBP from sleep. A number of things happen sometimes. Usuaully, when I wake the MBP from sleep, i get a black screen on both displays and all I can see and control is the cursor. Sometimes the main display will be black, but the MBP display will show the desktop wallpaper, but again, I can only see and control the mouse cursor. It should also be worth mentioning that the keyboard is rendered non-functional as well.
Sometimes, OS X will appear on both displays, with mouse cursor active, keyboard inactive, but I am unable to click anything or interact with anything OS X.
Anyway, I'm at the point where I need to mention this because it happens quite frequently and its getting rather annoying. The only way I can get out of this hang, is to cold reboot the machine. It happens everyday and at least 50% of the time I wake the MBP from sleep. When not connected to the display, I never get this occurrence. Also, this display worked perfectly when I used to own the classic 15" MBP, so its hard for me to pinpoint what exactly is the anomaly that is happening.
Anyone else experiencing this same issue? I am using a mini display port to DVI adapter to the Dell display.
Well my unibody macbook display decided to screw up last night, it was working fine last night no problem. Connected to a external monitor. I fell asleep last night with front row left on, obviously it went to sleep and then I woke up and the screen was black. Now the LED lights are working, my external display is also working. The display settings recognize a screen being present (when I click detect displays and gather windows - 2 windows appear). Ive reset PRAM, SMC, reseated the RAM, control+shift+eject (which just made the screen flicker a little after turning it back on) and Im out of ideas. Its out of warranty and about about 18months old.
View 4 Replies View RelatedMy Mac Book Pro just stopped accepting commands, the screen is freezing on a black screen and the keys have no bearing on the situation. The only way I can get it to stop is pull the battery out. It has been acting funny lately.
Info:
MacBook Pro (17-inch Early 2008), Mac OS X (10.5.6), final cut express
my one key when pressed brings up the brightness which then scrolls all the way to black. I have to close the lid and open then press F2 ti get my brightness back.Â
Info:
MacBook Air (13-inch Mid 2012)
I've noticed that when my rMBP (late 2013, Mavericks) turns off the display automatically while on battery (as configured via Energy Saver) and I try to wake it immediately, I get a black screen with the cursor, rather than my password/unlock screen. It remains a black screen, with the cursor moveable, for 5-10 seconds or so, and then the password/unlock screen will appear as usual.Â
This does not happen if:I don't try to wake the display/computer immediately after automatic display sleep (e.g., I wait 5-10 seconds and it's fine)I turn off the display using a hot corner and immediately wake the displayI put the computer to sleep by closing the lid and immediately wake it by opening the lidI select Sleep from the System/Apple menu and immediately wake it by pressing a key or clicking on the trackpadÂ
Why automatic display sleep is causing this temporary black screen? I currently get around it by setting the time for automatic display sleep while on battery to 10 minutes instead of the default 3 minutes to minimize the chances of needing to immediately wake the screen. I'd like to keep it at 3 minutes if possible to maximize energy savings, but the temporary black screen is really annoying if I didn't really want display sleep and consequently have to wake immediately.
Only way to recover is hard restart. Just downloaded Lion two weeks ago - problem started shortly after.Â
Info:
MacBook Pro, Mac OS X (10.7.3)
had my yosemite upgrade and everything was fine but I notice that Thunderbolt port has stopped working.
View 1 Replies View Related
