MacBook Pro :: Replacing The Bottom Case - Get Exact Part Number?
Jul 29, 2009
I am needing to replace the bottom case of my late 2006 MBP. It has a large dent in it that is causing some problems. My question is, do I need to get the exact part number listed on the bottom of my laptop (A1211) or can I get a bottom from any pre-unibody MBP i.e. A1260? Also, has anyone ever replaced this part? How difficult is it? I have experience working on laptops, I've just never taken a mac this much apart.
I went through all the steps to change the optical drive on an old 500 MHz iBook G3, but am unable to attach the bottom case. The problem is the two long (20mm) screws near the back of the computer -- each apparently has to insert into something that looks like a gold-colored nut with serrated edges, like gears, otherwise the screws just rotate in place and don't "lock up." I'll attach a picture, but my only digital camera until I borrow one from a friend is my cell phone, so the pic won't be too good. The gold pieces fell out during the disassembly process and I can't figure out where they now go.
I was wanting to know how hard it is to change top and bottom case and keyboard area? I would like to know that if anything was to happen to my soon to have macbook I could change it. Also this on the older macbooks. And if I have Apple to change it how much would it cost? And yes I know that they should replace keyboard case area for free because of the defunct cracking issue.
I did a search and could only find information about the last rendition of mbps, and I see they had problems with bleeding along the bottom part of the screen. I just got my umbp a week ago, but I've been so busy finding a place to live for grad school that I haven't had the chance to use it. I looked at it in the dark yesterday, and I'm super anal. I saw a small amount of backlight bleeding on the bottom left corner of the screen, perhaps half an inch on the left side of the screen, just in one area (not along the entire left side).I wish I could take a picture, but my digital camera is nowhere to be found. Is a small amount of backlight bleeding acceptable, or should I exchange for a new umbp?
The bottom part of my Macbook is peeling off I have no idea why, its never been dropped scratched exposed to extreme temperature. I noticed about a week ago the bottom part had a bit of a crack where its suppose to meet on the edge, I woke up this morning to find this!
is there a way to check a part by number? from apple. I got my repaired laptop back and the 3rd thing they replaced was a "cover" - "mechanical / cosmetic damage" cover of what? i have the part number, is there a way to see what this is exactly?
I am trying to find out how many files I have on my Internal HD so as I can match them to the copied files on my external HD before I re-format to make sure they have all copied.
My external is MS-DOT (FAT32) and the internal OS Extended Journaled giving me a difference of roughly 7GB, I can only bring up the capacity, available and used information.
Some weeks ago I dropped my MacBook Air (well, actually I couldn�t do anything, my bag was broken so it dropped) and got quite a noticeable dent in the bottom left corner on the screen (outside, you can see the dent while closed). I tried to live with it but with such an expensive machine I can barely do that. So I tried to find a replacement part, the display housing. But - I can�t. I can find replacement LCD displays, replacement housings f�r MacBooks, for MacBook Pros - but NOTHING like that for the Air. Seems like this is Murphys law, eh? This really sucks.
My girlfriend's MacBook has some deep scratches on the bottom that a polish kit would not fix. I wanted to buy a new bottom cover and replace it for her. I have found quite a few on eBay, but I am not sure on which model will fit. She has the new white NVIDIA MacBook. I assume that because the motherboard is different, would she need a case specific for the NVIDIA model, or will an older Core 2 Duo case work all the same?
i've had my top case replaced three times already and it's broke again. it only takes a day or two to get it replaced at my local authorised repair centre, but is it worth ringing apple and trying to get the machine replaced? i mean, there's no point in replacing the machine with the same model because it'll just happen again, but i can't imagine apple giving out one of the new machines though.
for reference its a 2.2GHz white macbook bought in november 2007 and the top case was replaced the first time around jan/feb 2008, and then twice in 2010. obviously the applecare runs out in november of this year so want to get this sorted out asap.
I was woundering if anyone know where i can buy some screws for the bottom of my macbook pro i7 15". I lost one screw when replacing HD and memory. Everywhere I see online wants to sell whole macbook pro screw sets. I only need 1 or maybe anther for a backup. Don't want to spend 50bucks on a set of screws just to use 1.
I am wondering if anyone knows what Apple charges to have the bottom plate of the MacBook Pro replaced. When I was at a store, an employee told me that it "might cost, like, uh, forty bucks," in a way that made me think he was just pulling that price out of his you-know-what. After searching eBay for that part and finding no auctions for less than $100, I assumed that Apple would charge something more like that.
It's really irritating that in order to replace two of my footpads, I must replace the whole bottom plate of the body. Apple is really trying to get people to buy the service plan, and then a new laptop when that runs out. Great for the environment. The whole unrepairable Retina Display MacBook debacle is just more proof of that.
So I bought a refurb nvidia White MacBook a couple weeks ago and one of the problems I have noticed is that the screen is not flush with the bottom case when closed. The problem is worse on the right side than the left (near the indicator light).
I know that with refurbs you risk getting a slightly less than perfect computer. However, I don't want this problem to get worse. When I first got it I didn't really care but now I'm thinking of the future and of the "what if it gets worse" scenario where I take it in and they think I physically damaged it by accident.
I have had this quad g5 (dualcore 2.5ghz X 2) laying around for about a year that I purchased for $100 without a hard drive, super drive or a power cord. I was told that it was non working in the manner that ONE of the dual core cpu's had gone bad. I will be receiving my power cord this week to make sure that it still powers on but what the problem is.
My question is: If only one of the cpu's are bad, what is the part number I will be looking at? I am not wanting to spend a fortune on this to fix it, but If I do get it working I would like to drop 8-16gb ram in it, and setup a raid with 2 raptors.
I have a mid 2009 macbook (nvidia 9400 version) and i have recently noticed that there is quite a lot of hairline cracks around the speakers on the bottom case, and the screen bezel has actually split at the bottom, and the last couple of weeks the screen has been creaking, i originally thought the creaking might be related to the cracks but it seems to be coming from the actual screen its self.
I know that apple repair out of warranty for cracks on the palm rest, but that area of my macbook is in perfect condition so i'm not sure where i stand here, how much would it cost to have all the casing replaced e.t.c do you think?
it's not really a long story, i have a macbook i got in feb. 2007 i paid 1299 for it, (not like it matters, but it's kinda why im annoyed lol) Well, i was carrying it today, and realized that the plastic by the vent i guess? it's on the bottom of the case near the back edge. so anyway, it is cracking, but not from outside it. it just runs straight across. Will apple help me even though I have no applecare? This seems like a manufacturer's defect to me, but i was hoping macrumors' collective knowledge would have a scenario or someone has been through this before. I'm getting pics ASAP!
I was hoping that Apple would address this in the new MBPs but alas it seems they are the same.I hate the fact that my 15 and 17 mbp bottom cases are too flexible and will actually pop in and out if you hold it in the middle.I think on my new mbp I did this and accidentally heard the fan hitting the case.To get around this, you must hold the mbp from sides only.
When I apply pressure on the bottom case of my MBP(underneath the trackpad), I hear a click. Is this normal? I am currently using the current MBP13'. What is under there? Am I damaging anything?
Is it possible to find out the RAM manufacturer on a Macbook (it's a 3rd party module) by the part number? I've been searching for the past half hour, didn't found anything relevant Here are the full RAM specs:
Could someone please tell me the part number for the 24" iMac 2.66GHz model, as I'm looking at purchasing one through work therefor I need the part number. And hints and tips for a first-timer?
So recently I found a cheap powermac G5 on ebay and won the deal and all, but when the computer arrived it was horribly dented. It was packed with on piece of under a 1/2" Styrofoam. In the end I got a full refund for the computer and the seller just said that I could keep it if I want it. So I wanted the thing on my desk so I went ahead and bought another case for it. Now here's the question, has anyone done this or knows how to do this? I want to keep all of the internals inside for it not to become a month or so long project in my spare time. I am not sure on a tool that would let me get up into the edges. If you want to see some video of the unboxing of the case and at the end some footage of the dented one and how bad it is go here.
I have a late 2006 macbook and had the issue with the cracking case repaired today, however, Apple only repaired half of the issue. The 'top' half of the case was fixed (new keyboard, trackpad etc) was replaced and I am more than happy with it. The bottom half of the case (section with USB ports, bottom of the MacBook etc) still has cracks in it and clearly hasn't been replaced. Is this something that should be replaced as a manufacturing fault as they have done with the keyboard, palm rest, trackpad etc?
I have to replace the bottom case of my peryn 2.4ghz macbook pro. I was wondering if anyone bought from usedmac.com and if this model would fit my computer? I will just order this part and go to my apple university shop where a friend of mine works there as a techy and he can change the bottom case.
I was wondering if anyone has the part numbers for the new Time Capsule releases (500gig/1 tb). I want to know if the ones at my local stores are old or not.
I would like to replace my 1st generation unibody MacBook Pro's bottom case and I am interested in knowing the price. Can I purchase and replace the bottom case at the local Apple Store (I'm in Sydney)? I'm in warranty, if that's a factor.
