Software :: Powerbook G4 Won't Boot Properly/wake?
Jun 29, 2008
I am currently running a 15" Powerbook G4 1.67, 1GB ram, latest update for 10.5.
Yesterday my computer randomly went to sleep and wouldn't wake up. I forced it to shut down and then tried rebooting it. It started up, but went to sleep before even getting to the login screen. I have searched the internet, this website, and the apple support site to try and fix the problem.
I have tried resetting the PMU (although I don't know if I did that correctly), leaving it to rest without any battery or AC power hooked up to it, and the CMD + ALT + P + R reset all to no avail.
It seems like the general outcome for random sleep problems hasn't been too good,
View 2 Replies
ADVERTISEMENT
Jan 18, 2009
My Powerbook was given to me and it started to work properly when I set it up with my ISP and then one day I put it in sleep mode and it never woke up .
It starts with a chiming sounds and then it goes light grey.I then see user abort on the screen telling me to type mac-boot to continue rebooting or shut down to shut down.
I has a welcome to firmware and I think I pressed too many keys too many times including the FN key.I don't have the manuels to troubleshoot this laptop but the seriel number is QT0272GAHDR and it is an Apple 20gb.
View 1 Replies
View Related
Aug 12, 2006
My G4 Rev E PowerBook won't wake from sleep. The battery died and the computer slept, but now when I boot it, it gets to 3.5 progress bars and freezes. I have tried rebooting but I can't seem to get out of the resume from sleep mode.
Any ideas? It doesn't show the grey Apple screen like it does from a fresh boot, just the progress bars that show up when the battery dies.
View 1 Replies
View Related
Aug 6, 2008
Recently my powerbook g4 aluminum 15" won't wake from sleep mode, and i can't turn it off with the button. When the computer does turn off the only way i can get it back on is to open it up and reset the logic board by disconnecting the back up battery for a little bit. I've tried reseting the PMU,
View 6 Replies
View Related
Jan 14, 2010
When I try to print from my Powerbook G4 to my HP 6500 wireless printer it will not work. I have found out that if I turn off/on the printer then it will print. So, it must be an issue with the computer not waking the printer from a sleep mode. Anyone have a solution to this that doesn't consist of me turning off then on the printer? I have tried to reinstall a few times with no avail.
View 2 Replies
View Related
Sep 11, 2008
My G4 powerbook (running Tiger) seems to be stuck in sleep mode. I turned it on and the screen remained black but the sleep button is flashing on the front.
View 1 Replies
View Related
Jul 19, 2008
I have a problem...my 12" Powerbook G4 doesn't start up properly at the moment. I turn it on, I can hear the chime, and the screen goes grey but then does nothing...I've tried holding down C while starting up too, but still nothing happens, just the grey screen.
View 5 Replies
View Related
Jan 26, 2007
My G4 powerbook has been saying recently that the start up disk is full, so i tried to empty some stuff off it. But not long after this when i tried booting it up the normal happens at first ie the t'ing' start up sound and the apple sign with the little timer going round but it does nothing else, it just carries on going round. I have tried re setting it and looked on help sites like this to try and override it etc but nothing seems to work!
View 4 Replies
View Related
Jun 28, 2007
About a week ago I received my new battery due to the recall. The last few days my power book has been great when I open my power book today it will not wake up. So i figured I would plug it in. The light stays green, does not change to orange, and still continues not to wake up. Even taking the battery out and trying to turn it doesn't work. Power cord stays green then as well.
View 4 Replies
View Related
Jun 29, 2009
I recently purchased a sort of beat up 1.5GHz 12" PowerBook G4, top of the line, and it arrived today. It boots up normally when the apple appears, then it shows the blue screen and then the mouse turns into a spinning wheel. Also, when I move the cursor, a second cursor from the same spot stays in the top-left corner. The PowerBook will only work normally as a headless server (powers on, lid closed), unless booted in safe mode. Another issue is the screen. The seller said there were lines going up and down the screen, but it varies depending on what is displayed on the screen. If the screen is grey or in target-disk mode, they do not appear, but on the 10.5 standard desktop pic, it changes pattern. The lines can be seen here: [URL]
View 1 Replies
View Related
Sep 13, 2009
I have OSX installed on a very old Powerbook. Well it was working and then I left it for awhile and now it is giving me the good old folder to question mark screen (maybe someone dropped it?). Well I'm not much of a mac user so I looked up all of the different boot key commands and tried to boot from my OSX CD. Holding down C did nothing, and neither did ANY of the other commands except holding down option and that key command that restarts the computer (apple, option, shift, esc?). Anyway, I got into the screen that shows your hard drive and all other devices and it actually listed the CD drive so I clicked it and clicked the next arrow. I waited for awhile and then the screen reloaded (as if it was rescanning for removable devices) and then stopped and only displayed the local disk. What is going on?! It only sometimes displays the CD in this screen and the next arrow never does anything regardless!!
I really don't know any of the computers stats but if I were to guess they're pretty bad. All I know is it used to run OSX just fine and then other people used it and now it doesn't do anything.
View 7 Replies
View Related
Oct 17, 2010
Got a Powerbook G4 with a "messed up" HD. Couldn't fix it, so got a firewire drive and ran a bunch of utilities from my newer intel iMac. Cloned the Powerbook's drive to a USB hard drive, did all repairs on the USB drive, formatted the Powerbook, cloned the USB drive BACK to the Powerbook, but it just gives me the flashing question mark when I try to boot.
What is REALLY weird is I can boot my iMac FROM THE CLONE ON THE USB DRIVE and it works fine.In Drive Genius the Powerbook drive (in TDM) shows as a single drive, but if I go to "Repartition" then it shows 3 smaller partitions on the drive; I believe they're called "Apple Free Space" or something like that (can't check right now, I'm running Repair on it AGAIN at the moment).
I feel like I'm missing something simple, like the machine just doesn't see one thing that tells it "Oh, yeah! There's an operating system on this drive!" I have tried partitioning from Drive Genius and Disk Utility. Have done clones back and forth with Drive Genius, Disk Utility, and Carbon Copy Cloner. Same results each time.
View 6 Replies
View Related
Apr 6, 2012
When I turn it on the whit screen comes with apple, then after a few minutes it goe off
Info:
iMac, iOS 5.0.1
View 1 Replies
View Related
Apr 18, 2012
Recently I inherited an iMac G5 (no iSight) that has bluetooth and a preinstaled airport card. When I recieved it the drive was wiped so I did an install from the original disks. My problem is that the computer will not boot properly ; I can hear the chime, mostly the lcd lights up but it stays black, sometimes I will see the gray screen and from there it will either go to the light blue screen and hang or it will distort the picture and the fan will kick in. 2 out of 20 times it will boot successfuly but after about 1 min. it will freeze up, distort the image and then the display goes crazy! I don't know whats wrong... the capacitors have been replaced a not too long ago along with the power supply, and I ran a hardware test and it says everything is fine ( the G5 won't recognize the airport card or bluethooth!). I need help!
Info:
iMac, Mac OS X (10.4.11), PPC G5 (no iSight)
View 12 Replies
View Related
Oct 21, 2009
I installed Windows 7 onto my MacBook(black) and whenever i put Windows 7 to sleep such as closing the lid it doesn't wake up. My screen just stays black but i can see in the background that the OS is still running and still works.
View 1 Replies
View Related
May 27, 2012
I orderd 8 gig's of RAM from Apple. Installed it per the instructions. Now, the MBP with Lion boots up and runs fine from off, the activity monitor acknowledges the 8 gig's. Runs well.
When I close it and then open it back up, the screen stays black and the sleep light goes out.Also, sometimes it won't boot, the light blinks and it makes a beeping noise over and over until I do a hard shutdown. Also, a couple of times, I was using it and the graphics went totally screwy and were blinking and whatnot until I did a hard shut down. Can I return the memory (a shame because it is better with it when it works). Software Mac OS X Server Lion 10.7.3 (11D50)Graphics Intel HD Graphics 288 MBMemory 8 GB 1067 MHz DDR3Processor 2.53 GHz Intel Core i517-inch, Mid 2010
Info:MacBook Pro (17-inch Mid 2010), Mac OS X (10.7.3)
View 2 Replies
View Related
Apr 16, 2012
I have a strange boot issue having (tried) to install EFI 2.7 update. When I restart the laptop, it 'chimes', displays a grey screen, then chimes, displays a grey screen, forever. I hit the bower (off) button for 5 secs or thereabouts, and restart, same thing. I do this 4 times and finally it reboots. But the EFI update still appears as needing to be installed (software update tells me it is not installed). Update history shows however that it IS installed. I can go through this process any number of times. I now have Software Update history showing quite a few installs opf the EFI 2.7 update. If I just do a restart without installing, I also go through the same fail to restart / fail to start / ... / eventually restart sequence.
So it seems now that the laptop will only start after 4 failed restarts and finally it starts. After starting it all appears to be perfectly fine. Nothing strange in the console logs that I can see. The failed reboots don't seem to register in the console logs - I suspect that the failure to restart is pretty early on in the boot sequence, well before it tries to load any semblance of the OSX kernel. It is almost as if it is trying to boot from someplace other than the disk ... until eventually it gives up and tries the disk. (I have tried booting with and without network cable - no difference) I don't know enough about mac bootup sequences to know if there is some config/setting that is screwed up causing this odd behaviour.
Info:
MacBook (13-inch Mid 2010), Mac OS X (10.7.3)
View 5 Replies
View Related
Mar 9, 2009
My MacBook had the trackpad clicks-not-registering problem that was cleared up by the Trackpad Firmware Update in November. Unfortunately, a variant of that problem seems to have surfaced. When waking from sleep or on boot, roughly half of the trackpad's clicks won't register, forcing me to click two or more times to start an app or read mail. After five or ten minutes, the problem seems to abate. I still "lose" clicks now and then, but not as often. Note that other trackpad functions seem unaffected when this happens.
I've tried resetting the SMC (no effect) and PRAM. Resetting PRAM cleared up the problem but only briefly, and now it's recurring.
I took the MacBook to the Genius Bar and the Genius suggested I use "tap to click" instead, but while that works, I'm a sloppy clicker and found that setting irritating.
View 5 Replies
View Related
Mar 21, 2012
I installed the latest version of Lion on my mid-2009 13" MBP yesterday. I recently got a Corsair 256GB SSD (model CMFSSD-256D1) and that's what I installed Lion onto. It seems this behaviour has only been happening since I got this SSD. What happens is when I put my computer to sleep for a long period (say, 2 or more hours), when I wake it up, some of my applications show the spinning beachball - though some of the applications still seem to respond. After playing around with the responsive applications for a bit, they eventually start beachballing as well. After a minute or two the entire system is beachballed and I can't do anything. My only option is to do a hard shutdown. (It almost seems like the SSD has decided not to respond to requests?)Â
When this happens and I do the hard shutdown, I consistently cannot boot my MBP at this point. I shut it off again, wait a bit, turn it on, and try booting again - nothing. The screen is all white (maybe light gray), and the animated gear never appears. I do hear the boot sound. When my MBP is in this state, none of the special boot options work - e.g., holding down "shift" for Safe Mode, holding down "option" to choose another boot drive, holding down "command+R" to boot from the recovery partition - it's as if I hadn't held those keys down at all. The only keys that do work are "option+command+P+R", which resets the NVRAM. After I've resetted the NVRAM, it still doesn't boot right away. I turn it off again, turn it on, and finally my MBP boots totally fast and fine. I do a check of the disk and there are zero disk/permission errors.Â
This is totally reproducible behaviour. Every time it's in sleep mode for a few hours, it does this, and I can't boot, and the only way I can boot is by following those steps above.Â
If I put the MBP in sleep mode for just a couple minutes to test it, it comes back from the sleep fine. I'm not sure how long it has to be in sleep mode before it decides to beachball on wake.Â
I have done a search for new firmware for my SSD and have come up with nothing.
Info:
MacBook Pro, Mac OS X (10.7.3), MBP is mid-2009 13"
View 4 Replies
View Related
Jan 11, 2009
Today my Powerbook fell to the floor from about 2 feet up.
At first all seemed OK, but I then noticed that Safari wouldn't start up, so i went to reboot to see if this would resolve the issue.
Anyway, upon turning the powerbook back on, it is going no further than the very first screen of the light grey background, with dark grey Apple logo in the centre of the screen, accompanied a few seconds later by the revolving "please wait" icon (apologies if this icon has a technical term - unfortunately i don't know what it's called!), and it just stays like that, without getting to the blue login screen.
I have tried going into Single User and Verbose modes to see if i can boot up that way, but no joy.
View 1 Replies
View Related
Jul 6, 2009
I'm having an issue with my PowerBook G4. It wouldn't turn on at all before, so I installed another motherboard. Now it will power on, but it only shows this folder icon that blinks. I'm a complete n00b to macs. If this were a PC I would of fixed it by now. I need some help. I've tried the installation disk, but when I hold down the C key, it takes longer, but it just shows that folder again. When I hold down the Option key, it only gives me a reload button, and an arrow button, but no boot up options. Do you think it could be a problem with this other used motherboard? Or is it that I just didn't put it in right? I've double checked all the hardware, and it seems to be all connected. The keyboard lights up, and the trackpad works, and it makes the boot-up sound.
View 8 Replies
View Related
Jun 23, 2008
I have a G4 Powerbook laptop. I have never had any trouble with it. It suddenly now will not start OS10. It starts up fine and the blue screen comes up and it says starting OS X. the blue bar lights all the way up then it just gets stuck.
View 1 Replies
View Related
Oct 15, 2008
My sons powerbook G4 died. He said it got slow and just hung. He forced it off and now it wont boot. It comes up to the apple logo then stops. No spinner or anything. I reset power management. When I try to boot from the install CD I get a kernel panic.
View 2 Replies
View Related
May 9, 2012
My Power book will not boot up. Upon powerup up I get the usual "bong" sound and then after several seconds I get a large icon in the shape of a gray folder blinking on and off with a white queston mark inserted in the folder. I have run the hardware test on the applications install disc and it checks out OK with the advsnced test. I have tried to reboot using the OSX Install DVD but it will not boot holding down "C" when starting up. When I try to reinstall OS X it stalls out because it cannot find a drive file to install in. Any ideas on what has crapped out, is it HD issue?
Info:MacBookPro, Mac OS X (10.6.3), Model A1278
View 5 Replies
View Related
Oct 6, 2010
I just recently purchased a powerbook g4 (1.33 12 inch) from PowerON Services. I turned it on for the first time and I was prompted to update to stuff ( osX being one of them) It then froze while installing the updates.
Now It wont boot, it is stuck on the grey screen. I tried loading from a tiger disc that I have but that didnt work. I just get a funky message saying to hold the restart button. Any words of wisdom??????
also note i tried resetting PRAM and tried booting in safe mode.
View 6 Replies
View Related
Mar 24, 2012
I have had OSX 10.5 installed on one of my hard drives for quite some time and use it occasionally. Yesterday I installed the update to 10.5.8 and it will not boot anymore. The updater reported a successful installation, but when trying to boot from 10.5.8, the little lines in the startup circle keep going around for up to a half hour without end. Unfortunately, I cannot find my original 10.5 upgrade disk, though I still have the packaging and documentation that came with it.Â
Info:
Powerbook G4, iMac G5, Mac OS X (10.4.3)
View 3 Replies
View Related
Sep 13, 2009
I have a very old PowerBook that did have OSX running on it fine. Recently it has stopped working completely and when you startup it takes you to a blue screen with a question mark and a finder icon flashing on top of a folder. If you give it long enough it will just shut off. I have tried booting from a CD but I can't seem to get that to work. I boot up holding down the option key and it brings me to a window with a picture of my hard drive and a picture of the CD drive but when I click the cd drive and then click the forward button it merely acts like it's refreshing the list and doesn't actually boot from the CD at all. I've also tried holding down C during boot up but it ignores that and just goes to the same old flashing question mark and finder icon screen. The CD I am trying to boot from is the same OSX cd that I originally installed OSX on this computer from so I know it works.
View 2 Replies
View Related
Jan 24, 2007
I have a powerbook 12' 867 mghz, I know I would rather have a new one, but not ready to give up on this old gal yet! Anywhoo I thought the logic board was fried but after letting the powerbook "rest" I came back months later and sometimes it will boot but as soon as I try to do anything it freezes, so maybe the harddrive is fried? How do you get it to ignore the internal drive so it will boot from an external?
View 9 Replies
View Related
Dec 2, 2008
I just recently started to experience some very unusual behavior on an older PowerBook G4, and I was wondering if anyone has experienced this before, as I can't seem to find any documented info on this.Basically, out of the blue, the user began to experience issues waking from sleep, while using the laptop closed with external monitor, USB keyboard and mouse. Although a powercord was always connected, the machine seemed to be powering off.For a while, hitting the power button would boot things up again, properly, but not anymore. I have since disconnected all peripherials. Now, when pressing the power button, the machine will beep 3 times and then repeat itself every so often. The sleep led will blink three times, go solid, then repeat. Sometime the harddrive tries to spin, sometimetimes not
View 1 Replies
View Related
Sep 1, 2009
I have a second hand 12" PowerBook G4 that sometimes will not boot. It will sometimes chime and the LCD will stay black. Like I said this does not always happen. I have already tried to reset the PRAM and PMU and this does not seem to have any bearing on the machine.
View 1 Replies
View Related
