MacBook Pro :: Fails To Boot Properly After EFI Firmware 27 Update
Apr 16, 2012
I have a strange boot issue having (tried) to install EFI 2.7 update. When I restart the laptop, it 'chimes', displays a grey screen, then chimes, displays a grey screen, forever. I hit the bower (off) button for 5 secs or thereabouts, and restart, same thing. I do this 4 times and finally it reboots. But the EFI update still appears as needing to be installed (software update tells me it is not installed). Update history shows however that it IS installed. I can go through this process any number of times. I now have Software Update history showing quite a few installs opf the EFI 2.7 update. If I just do a restart without installing, I also go through the same fail to restart / fail to start / ... / eventually restart sequence.
So it seems now that the laptop will only start after 4 failed restarts and finally it starts. After starting it all appears to be perfectly fine. Nothing strange in the console logs that I can see. The failed reboots don't seem to register in the console logs - I suspect that the failure to restart is pretty early on in the boot sequence, well before it tries to load any semblance of the OSX kernel. It is almost as if it is trying to boot from someplace other than the disk ... until eventually it gives up and tries the disk. (I have tried booting with and without network cable - no difference) I don't know enough about mac bootup sequences to know if there is some config/setting that is screwed up causing this odd behaviour.
Info:
MacBook (13-inch Mid 2010), Mac OS X (10.7.3)
"Boot Camp Assistant cannot be used: You must update your computer's boot ROM firmware before using this setup assistant"."
That's the dreaded message I get every time I try to use boot camp 1.2. Unfortunately my firmware is already updated, and any attempt at updating my firmware (again) results in the message that I "don't have to update my firmware."
I've google'd this problem numerous times, but I have yet to find a solution.
i just restored new Mac OS 9 already so now i have a problem that say i need to update firmware so i follow the instruction i hold the programmmer button and it just pop up with white screen say welcome to firmware update continue mac boot or shut down? i have no clue why is that i mean it say it will update loud buzz so i waited for long and it didn't
Superdrive Firmware Update 3.0 fails each time, /Applications/Utilities/SuperDrive Update.app asks me to quit all apps and try again which I did but of no. I also retried with a reboot.
Just recently got back from a visit to my local Apple store in regards to a faulty power adapter. My Macbook started up fine at the store, as it has over the past two years. However, after getting home and trying to turn it on, the laptop fails to boot up. It sits at the grey screen with the Apple-logo and spinning progress circle, all while the fan starts to whirl as if my macbook were on fire. I've experienced a failed hard-drive before, so I know of the folder w/question mark screen, and this screen is not like that. I've also tried booting up in "Safe-Mode," but that won't work as well. I do have a start-up disk and external hard-drive... I'm just curious to see what other options I might have before reinstalling Leopard.
If rev C runs the GPU at a higher speed and hw otherwise is the same as rev B then why couldn't Apple release a firmware update to let rev BGPU rum faster as well?
Just got this through Software Update. More info here:
[URL]
Quote:
About MacBook Pro EFI Firmware Update 1.8 This update eliminates the noise made by the optical disk drive during system startup and wake from sleep on MacBook Pro computers. When installation is complete, run Software Update again, and install SuperDrive Firmware Update 3.0
To complete the firmware update process, follow the instructions in the updater application (/Applications/Utilities/MacBook Pro EFI Firmware Update.app). The updater will launch automatically when the installation is complete.
[URL] MacBook SMC Firmware Update 1.4 is available either through Software Update or via direct download, and is applicable to the following models:
MacBook (13-inch Late 2007) MacBook Pro (17-inch, Early 2008) MacBook Pro (15-inch Early 2008) MacBook (13-inch, Early 2008) MacBook (13-inch, Late 2008)
I finally brought the 13in macbook air. What are some good softsleeves for macbook air 13in. I want a soft sleeves that fits perfectly with macbook air and below $30. Is it possible?off topic: this is my first mac computer, how do I update the firmware to 2.0?
After the update, my MacBook Pro is extermely sluggish. Prior to the update, I was zipping along like most happy MacBook Pro owners. After the update, I constantly see the dreaded beach ball when doing almost anything with the laptop, Safari pages take longer to load, etc.
It's almost as if the udpate had the opposite effect and actually throttled down my WD 500GB HDD performance to a large degree.
Like I said, prior to the update all was good. I've been searching to see if there is a way to revert back to the previous firmware to validate that the update caused the problem but I haven't been successfull in finding anything yet.
I currently have version 10.6.2 update for my macbook pro and after updating the EFI firmware update to 1.8 I get an annoying pop up every time I start the computer. I checked for any additional updates to see if it will go away, but I seem to have all the updates. Is there anything I should do to get rid of this pop up? Pop-up window reads: your computer's firmware is up to date with version 1.8 of the macbook pro EFI firmware update.
Just downloaded new firmware at suggestion of my auto-update app. Since loading, the computer has been trying to reboot for over 45 minutes so far. Grey screen w/ Apple logo and spinning grey wheel...The firmware update info says not to turn off, unplug, etc until rebooted.
Installed the 2.8 firmware update on my late '08 macbook pro and after restarting it, it would just beep 3 times and not start up. I pulled my 8 gig kingston ram out, repositioned back and still the same issue. Slapping in the original 4 gigs of apple ram, it will start up and work fine though. Is there a fix to get the 8 gigs working again on the machine?
I just ran the latest firmware update for my 2011 mac book pro and after it installed it now won't start up, only getting to the gray screen before freezing there.Â
I've tried all the on line solutions I can find on Apple's site, but no luck.
MacBook Pro EFI Firmware Update 2.8 does not install. I was prompted several times to install and restart (MacBook Pro late 2008) and authorised it each time. In every case, the update was proposed again when Software Update checked. I have OS Lion latest version installed. What to do about this bug?
Info: MacBook Pro, Mac OS X (10.7.2), photos in Sony Cyber-Shot .jpg
Are there any known compatibiity issues with booting from an OS 10.6.x drive after installing EFI Firmware Update 2.5?I am running Lion (10.7.3) on my MacBook Pro (13-inch, Mid-2010) but have held off installing the firmware update because being able to boot from a 10.6.x backup drive is more important right now than internet-based Lion recovery. If there's no issue booting 10.6.x (and running apps), then I will go ahead and install the firmware update, otherwise I'll wait awhile longer.
Info: MacBook Pro (13-inch Mid 2010), Mac OS X (10.7.3)
I did the latest firmware update few days ago and went through that series of boots. It's a shame on me that I didn't jog down the ROM revision info before the update. According to the this link:
[URL]
The FM Rev should be MBA31.0061.B01 after the update.
My MBA 13 is still read MBA31.0061.B00 after I thought I did the update. Does that mean the update didn't go through?
I have a uMBP 13' base model. I just received my Western Digital scorpio blue 500g hdd that is SATA 3.0. Should I install the new firmware update before I load anything onto the drive so i can utilize the 3.0Gbps instead of the 1.5Gbps? Should I install it at all? Will I notice a performance bump? I also received 4gb crucial ram, should i install the ram before installing the firmware update? I was wondering if anyone else noticed the screen slightly getting brighter and dimmer, almost in intervals, when it is not plugged into the power cord.
This update eliminates the noise made by the optical disk drive during system startup and wake from sleep on MacBook Pro computers. When installation is complete, please run Software Update again, and install SuperDrive Firmware Update 3.0. When I boot my system I can hear that sound like ejecting a disk out of the drive like always... Is that noise they refer?
I'm confused why it says "Your computer does not need this update"? It's a MBP4, 1 and has some startup noises and (always has had IIRC) problems with it making noises that don't seem right. I've checked Software Update and there is nothing there (I just ran it and updated a minute ago). I'm curious why it says this, is there a firmware update 1.7 that needs to be installed for the MBP?
I have a macbook 2.4 alu (Late 2008) and Installed linux as soon as I got it.(I just like the cases). Anyway I know that you need to use apple update in osx to update the firmware. I can't dual boot because my HD is MBR. I thought of 2 ways.
A. Install OSX onto a usb device (Cost 30-40 bucks for usb) B. Take to apple store, Maybe they can do it.
I can't dual boot because my HD is MBR. I heard the new firmware updates stop a lot of issues.
My macbook pro 17 2011 late 2.4 i7 keeps rebooting when I try to update the latest efi firmware. Have to force shut mac and restart and abort installation?
Did everyone notice a significant slowdown of network speeds (wireless at least) after installing this update [URL] on a 2011 MacBook Pro (2.0 i7 15")Â
Info: MacBook Pro, Mac OS X (10.7.3), 2011 15" 2.0Ghz
 I installed the EFI Firmware update 2.8 on my late 2008 MBP (running 10.5.8) and so far, it's seemed to solve the flicker/screen blacking out issue. I can no longer take screen shots any more without them being corrupted, and sometimes the Finder window gets scrambled and my wife needs to re-boot. I'm guessing a corrupted pref file somewhere. Anyone run into this recently and if so, is there a .plist file I can delete?
I have a late 2011 macbook pro running OSX Lion, and it wont update the firmware to 2.7, it downloads the update then says its installing it but when i go back to software update it keeps coming up saying it needs to be updated. Im wondering what can i do to stop this or get it to update.
Info: MacBook Pro (13-inch Late 2011), Mac OS X (10.7.3)
