Power Mac G5 :: Tried To Install Got A Fail To Install Due To A Source Problem?
Dec 14, 2007
I bought the family pack for Leopard. I installed Leopard on my G4 laptop fine.When I tried tried to install on my G5 I got a fail to install due to a source problem (?)In any event I restarted from the Tiger hard drive and it's totally screwed up my computer. It tries to start and I get initial Apple logo for about 2 seconds then it locks up and I get a bunch of computer code.
Information:
G5
Mac OS X (10.4.9)
View 4 Replies
ADVERTISEMENT
Sep 1, 2010
currently i try to move all my files from old hitachi 250gb to new momentus via time machine , yet it fail after 6 percent. so i decide to do a fresh install of mac Os 10.6 but then it no responding at 27 minutes remaining . i try to use both DVD and external Hdd to install but still the same result . i tried to update the momentus Firmware via [URL] yet still same result?
View 4 Replies
View Related
May 19, 2009
I reinstalled my OSX a few days ago and it's back to 10.5.2. After running software update, it has Mac OSX Update Combine (737MB in size). So I clicked install per usual. However, after I finished downloading the file and it offered to restart and install, the installation failed. Meaning during installation, it stops 1/8 of the whole "installation bar" for 8 hours or so and it didn't budge a bit ever since. I'm not sure what to do now. Should I try to download the combo update from Apple website (729MB in size, not sure why the one in software update version is bigger in size) instead? And try to install that one instead?
View 5 Replies
View Related
Jun 11, 2012
Some days ago I went to upgrade my mac mini 2010.I downloaded the combo-updater, as this is my preference. I sometimes have trouble with the normal updater from software update.When running the install I get this message of error above. I tried doing it different ways, downloaded the updater numerous times to try again.I even REINSTALLED OS Lion from the original installer and started over with the same result, even allowing the installer to dl the update, as it asked to do so.So I completely started over with a clean re-partitioned drive and had the same result. I tethered it to my macbook pro 2010 in FIREWIRE TARGET mode and tried installing it that way, same result. I have also just let the Software Updater utility run and allow it to install the downladed update. That activity returns a "cannot expan" error message...End result: It will not for any reason install this update. This is a problem I have never encountered (in 25 years of using macs).
Info:
Mac mini, Mac OS X (10.7)
View 1 Replies
View Related
Jun 28, 2012
First I follow the boot camp assistant step by step, and my windows7 disk is connected to my mac.However, after it reboots, my screen turns black and the ''Non system disk, press any key to reboot'' appears.Now there is no respond when i press the keyboard, I have to reboot my mac by holding the power button.I have tried times and times, installing refit, using another disk but still cannot fail.
Info:
Mac mini, Mac OS X (10.7.4)
View 1 Replies
View Related
Feb 1, 2012
i am facing problem to upgrade my macbook pro 15 inch 10.6.3 to os x lion 10. 7 with recovery drive.Â
actually i m trying to install os x lion with the following method but could not install. i use 2 methods to install os
1st method.Â
i make a recovery drive with recovery disk assistant on macbook air 13 inch which is shipped with lion 10.7 . and i connect my recovery drive with macbook pro 15 inch on which OS is snow leopard 10.6.3, for upgrade/install OS X lion on my macbook pro 15 inch by recovery drive.Â
when i hold down option key i can see my recovery drive . i can boot through my recovery drive but when i try to install os x lion the computer says "you cant upgrade this version of mac os x "Â
2nd methodÂ
i made recovery drive on macbook pro 13 inch which is upgraded snow leopard to lion and then i try to upgrade my macbook pro 15 inch then the same problem i am facing  "you cant upgrade this version of mac os x "Â
Info:
MacBook Pro, Mac OS X (10.6.8)
View 1 Replies
View Related
May 15, 2012
I have an old power mac and want to get it online if possible .Does anyone know if ots possible to install an airport card into it and get online that way ?
Info:
PowerMac, Mac OS X (10.4.11)
View 4 Replies
View Related
May 11, 2012
mac g5 dual-core 1.8 ghz, 3.6gbram, newly installed ide dvdrom & burner (for pc, actually, works well on mac).sata 160gb hdd. i just got this mac g5 from a a friend, very cheap, its a old mac, but its ok. there is no osx or other operating system installed, the pmu has been resettet, and a new battery for bios has been inserted correctly. now that i cant get or have any leopard osx 10.5.8, i just need any linux os to install, in order to see if the mac is ok.later on, i will buy a second hand legal osx leopard 10.5.8 any tools, i can download, to check for hard disk is present, emery checking at start up / boot up ?, the dvdrom jumper has been set to master. the sata hdd has no jumper. i did now got hands on a linux ubuntu 10.4 lts sio, and burned it with windows 7 and my pc burner (i really don't know if this is the right way to do it, can pc burn the iso correctly ?, even if i can see all the folders and files on the cd ?, which i can!). i tried it, the mac dvdrom works, its reading the cd (pressing the option on power up/ startup).in the startup bios,
i can see linux as a thumbnail picture, which i can select, and the cd loads all necessary drivers to memory etc.then the boot shell screen appears, explaining me to press return key, or choose other option. i did choose pressing the return key. mac is reading the cd, until a few seconds later a black screen appears and nothing happens!.i also tried live install.it could be a graphics driver problem ? ( the graphics card is, i think, a geforce 5500 fx ultra 128mb agp). the mac did work perfect before i got it, with osx and apps, every thing was ok, but my friend gave me this with a clean install, no osx. from this, experience i can see, that the mac cpu, dvdrom, motherboard and, memory / graphics card is working perfect.i am in doubt about the hardddisk, shouldn't the led on the front case blink, meaning it reading from the hard-disk ?.later on i will try the hdd and dvdrom to try different jumper position, and try another linux distro, eventually i should be able get this mac up and running! otherwise i have to get another old mac g5, which i have to pay alot, properly?. hope not. apple wants 100£ for a leopard dvd. they must be kidding!. (i will buy a second hand osx). i just bought an iPhone 4s, and mac mini 2011, a week ago.
Info:
PowerMac, Mac OS X (10.5.8)
View 6 Replies
View Related
Mar 3, 2012
I have an older Power Mac G5 Which is running OSX 10.4.11 and I procured a retail copy of OSX 10.5.1 Single Disc Install DVD. I tried to load it and it does not load and it appears to be frozen with a grey screen and the apple icon. I let it run for over an hour and nothing seems to be happening. [code]
Info:
PowerMac, Mac OS X (10.4.11)
View 14 Replies
View Related
May 21, 2012
Is there any way to install Garageband on my Powermac G5?I really need it and i can only find newer versions for Mac os X 10.5 on the internet.
Info:
GarageBand '08, Mac OS X (10.4.11)
View 2 Replies
View Related
Jun 13, 2012
I have a Power Mac G4 with dual 1.25GHz Power PC G4 processor with 2Gb SDRAM.I am on OS X 10.5.8.Three questions:
1) Can I go to 10.6 or higher?
2) If I change the processor out to an Intel, can I go higher?
3) Is there any upgrades that would allow me to put a later OS X version on it, and if there is, is it worth upgrading?
I know it's old, but it works fine, and this is my first Mac (I've had it for 1 year - It was given to me), and I am breaking myself slowly from the PC
Info:
PowerMac, Mac OS X (10.5.8), Power Mac G4, 2core 1.25GHz, NonInt
View 8 Replies
View Related
Jun 22, 2012
My cd/dvd drive busted WHILE I was upgrading the OS to 10.5. Now I get the folder with the question mark when I start up, or a blank screen. Other than installing a new cd/dvd drive, how can I install the OS without the drive? I only have other Intel Macs to use, no PPC.I don't believe Firewire/Target disk will help much in this case will it? I don't need any data from the currently unreadable hard drive - luckily had transferred everything ahead of time, but also erased a backup OS 10.4 boot drive too soon.Â
PowerMac Dual 1.8Mhz PPC
View 2 Replies
View Related
May 22, 2012
I recently discovered my computer had died while it was sleeping. I tried charging it but am recieving the "Battery not charging, power source: power adapter" status.My power cord light is green, always. and the computer dies instantly when I remove the magsafe.
I've tried the "remove the battery, press the power button, plug in the magsafe" troubleshooting process, but it doesn't work.I've noticed that even with the battery out, the charger reads a green light.I've tried several outlets with the same results.Here are my battery statsÂ
Battery Information:Â
Model Information:
Serial Number:Â Â Â DP-ASMB016-384e-7636
Manufacturer:Â Â Â DP
[code]....
Info:
MacBook, Mac OS X (10.5.8)
View 1 Replies
View Related
Dec 13, 2007
I had to re-install 10.3 on my G5 after the hard drive icon icon disappeared from my desktop and the finder froze. Its back to normal now after I did a clean install of 10.3, choosing the archive and install option. What should be my next step? How do I get all my stuff in the 'previous system' folder (my music, photos, etc.) to the main account? Can I somehow log in my old account with all my stuff and delete the new one I had to make? What's the easiest way to do this?
Information:
G5 1.8 Ghz
Mac OS X (10.3.x)
View 1 Replies
View Related
Dec 15, 2007
I picked up a new ATI Radeon 9600 Pro for my PowerMAC G5 D2.3 to run my 30" ACD.
I was going over the installation booklet and its all in PC lingo.
View 4 Replies
View Related
Apr 21, 2010
I have a used G4 from a university surplus materials auction. The cpu had been purged of all programs and operating system. I attempted to install Tiger but installation stops at designating drive location.
View 1 Replies
View Related
Apr 25, 2009
I followed the instructions here: [URL] to install iphone sdk on power pc using pacifist. However after the installation of the files , the mac used md5 checksum to validate the files and files were found not to pass. I then cancelled the validation. However I could not find the SDK programs that were installed in the mac. How do I delete the 5gb of stuff that was installed as I can'tfind them anywhere? I then proceed to attempt one of the comments instructions on that page:
1. Make the iPhone SDK.dmg read/write-able with Disk Utility using convert -> to read/write.
2. Mount the R/W dmg.
3. You need to delete some unneccessary file so that you can modify the installer config file, because the image is completely full. I choose the PDF in the root of the dmg.
4. Modify /Volumes/iPhone SDK/iPhone SDK.mpkg/Contents/iPhoneSDK.dist :
- Line 71 ( in function agreedToSLA() ) - modify "return false;" to "return true;"
- Line 81 ( in function SDKPresent() ) - modify "return false;" to "return true;"
but I was unable to attempt part 4 as I couldn't find iPhoneSDK.dist to modify.
View 8 Replies
View Related
Apr 6, 2012
The power mac g5 starts up with the question mark folder thing. When I put in the installion disc in and hold down c, It has the apple logo and it gets stuck there forever.
Info:PowerMac
View 11 Replies
View Related
Apr 23, 2012
Can I put snow leopard on a Power Mac G5.
Info:
Magic Mouse, Mac OS X (10.5.8)
View 1 Replies
View Related
Jun 8, 2012
I bought a Power mac G5 from a guy my brother knows but it seems to be running slow and I cant install 3rd party apps, is there any way of resetting it with no install disk?
Info:
PowerMac, Mac OS X (10.5.8)
View 6 Replies
View Related
Jun 11, 2012
I'm trying to fix my mother-in-law PowerMac G4.   She doesn't remember the admin password and I've been trying to reboot from the install cd. However, after pushing the "c" button. Nothing happens and it boots normally.Â
Info:
iPhone 4S, iOS 5.1
View 7 Replies
View Related
Jun 16, 2012
I can't install Mac OS 9, because the page "Select a disk to install" is empty, so I can't choose a disk. The disk is OK and the Mac OS installer too. I am trying to install it because this is the last version that a Power Mac G3 supports.
Info:
PowerMac, Mac OS 9.2.x
View 1 Replies
View Related
Oct 14, 2007
how to install a Samsung SH-S183 sata burner?
Information:
Dual 2.0
Mac OS X (10.4.10)
View 2 Replies
View Related
Dec 27, 2007
Is it possible to install 4 SATA drives into a G5 tower? I didn't open it up yet cause I have to move so much material to get to it. I'm assuming you can purchased a SATA PCI card but is there room in the case for 2 additional drives?
Information:
PowerMac G5
View 1 Replies
View Related
Apr 8, 2012
I would like to buy a power mac G4 quicksilver and install the latest hardware i.e. i5, SSD etc.
Info:
Mac Pro
View 2 Replies
View Related
Apr 22, 2012
I have a Mac pro 1,1 model and recently upgraded the video card to a Saphirre 6870 card. It works great right out of the box on both Mac and pc side of my Mac pro. From my online research, this card seems to be the best card that works with my mac pro so far, however I plan on getting an even more powerful card to use exclusively on my windows partition for games. I want to get a 6970 card, but that one may not work on the Mac side, so I plan on using both cards (the 6970 for the pc side, and the 6870 for the Mac side). There are two ways that I think may be possible but I wouldn't know how. One, is there a switch device that allows me to switch between cards without having to disconnect and reconnect them every time ? And second possible way, is there a way to house the second video card externally with its own power supply? The issue if that the are not enough power connections for both cards, so is there a way to power one card externally?
Info:
Mac Pro Quad, Mac OS X (10.5.4)
View 3 Replies
View Related
Jun 22, 2012
I have a PowerMac G5 OSX 10.5. I bought it used without install disks. My password doesn't work for some reason.
I've checked with the seller to confirm the password and I'm sure of caps and spelling.Â
Can I reset the passworde without an install DVD?Â
Info:
PowerMac, Mac OS X (10.5), G5
View 1 Replies
View Related
Jun 30, 2012
My 8 month old Macbook Air power adapter seems to have failed. It may appear to work (amber light glows when plugged in) for a while, but it stops working soon after.
Info:MacBook Air (13-INCH, MID 2011)
View 1 Replies
View Related
Jan 27, 2007
I have a g3 dual usb ibook that has a DVD/CD drive, 640 ram and a firewire port. I just bought a G4 800 mhz tower that has a gig of ram, but it does not have DVD drive (it's a cdrw only). My Ilife install disk is a DVD, is there anyway to use the DVD drive on my ibook to install software onto the G4 tower? Both devices have firewire but if possible I would like to use an ethernet cable connection between the two. I dont have the correct firewire cable(it's expensive).
A second question is i an os 10.3 on my ibook and 10.4 on my G4 tower. Is there a easy way to transfer all my files, settings, ect... from the ibook to the G4 tower? I don have the osx 10.4 install discs either (if that matters).
View 2 Replies
View Related
Mar 23, 2012
I lost my iweb and had order replacement DVD from apple after talk with support team. When I install its say "you cant open the app installing mac os x because power pc app o longer supported"
Info:
MacBook, Mac OS X (10.7.3)
View 2 Replies
View Related
