I have an eMac 1Ghz with 10.3.9 on it and I just bought a new Lexmark Wi-Fi Printer. I have no Extreme card, just a Netgear Wired/Wireless router that's obviously connected to my eMac via CAT5 cable. I set up the printer for wireless, hoping my eMac would use the router as a card-substitute type deal. Well it doesn't. Cannot connect as if it were not there.
View 9 Replies
I recently purchased an iMac desktop and installed it in my home office. It worked fine, except that the airport was connecting erratically to the wireless router, which is located about 5-7 meters away in a different room. I tried re-positioning the iMac to have better 'reception' but the problem persists. I can see the number of airport connectivity 'bars' changing every second and then going off fully. Very frustrating.
Could there be a problem with the iMac antenna? A colleague told me that if there's a wireless phone in the house near the router that can cause problems. Another told me that the router (a basic D-link 802.11g, 5 yrs old) needs to be replaced.
I currently have the netgear router set with an IP address of 192.168.1.1 with DHCP enabled and no security set up (i originally had WEP enabled but this made the problem worse.
I then have two sitecom range extenders set up connected to the router wirelessly to extend the signal in opposite directions. One is set up with an IP address of 192.168.1.2 and the other 192.168.1.3 with default gateway set at 192.168.1.1 and DHCP disabled. This sets the network up working for a short time however as soon as more than one machine tries to connect to the network it all shuts down. It seems that the setup cannot assign IP addresses to more than machine at a time.
I have a Power Mac G4 dual 876Mhz MDD ,recently bought. I am trying to connect to the internet and am having no problem when I connect an ethernet cable to a netgear Wireless router that shares the connection. However as I have an airport express base station, would it be possible to connect the airport express base station to the powermac via ethernet and then connect to the internet wirelessly via the netgear router and airport express base station?
View 1 Replies View RelatedI recently acquired an iBook G3 600MHZ with an Wireless B Airport Card. My router is a Netgear WNR2000 that is standard N but is backwards compatible with b/g. I have no idea how to set this up. I've tried and it doesn't connect. Oh, and I am running 10.2.8.
I went to Starbucks and it connected there instantly. So I don't know what's going on.
I have an OLD Ti Book. (667 MHz, G4; 1 GB RAM, running 10.4.11). Just bought a SISCO Linksys wireless-n router (dual band), high performance. It is set up properly, as my iphone is connecting and my work PC laptop connects too. I am assuming that my old, but kick ass powerbook does not have an airport card built in? So, I assume I need an adapter? We bought the adapter that went with the router, but after I got it home, realized it is only for windows. Did I miss the MAC one, or can I use this one.
View 2 Replies View RelatedJust wondering, as the title suggests, whether the Brother HL-5370DW mono laser printer creates its own wireless access, or do I need a router?
View 1 Replies View RelatedI am running Win XP Pro, and my wife is running OSX with the printer connected to that via USB. How do I allow my comp, running Boot Camp, to see the printer connected to her comp?
View 1 Replies View RelatedMy MacBook Pro is connected to a wireless Belkin network with no issues, but I cannot seem to add the printer to the same network.Â
Info:
Mac Pro, Mac OS X (10.7.4)
I need to know how I can set up a system so that I can use the printer and browse the internet wirelessly on the MacBook Pro and have the non-wireless PC connect to the internet and use the printer as well.
It sounds confusing, so hopefully one of you guys will be able to understand it and maybe quickly draw a labeled diagram to show me.
I have a home wireless group with a pc desktop and hp1200 printer. I have been unable to connect my macbook pro (0SX 10.6) to either. I am able to log on to the home wireless network. And my pc laptop can access the printer and desktop files.
View 6 Replies View RelatedI have an HP office jet J4680. I have used it wirelessly by being connected to my time capsule network and printing from my macbook for over a year now. I just moved and changed the name of my time capsule and the printer is no longer connected. I have looked around on how to select the new network but I don't see this option. How can I link the printer with the network again?
Info:
MacBook, Mac OS X (10.7.3), 2 ghz intel core 2 duo, 2 gb, ddr3
I am a new intern with a small company and am trying to connect my Macbook Pro's printer settings to our office printer, which is a LanierLD145. We halso have an HP3600 on the same wireless network which my Macbook can detect and print to just fine via the shared network server. However, when I try to find the LanierLD145 I can't find it anywhere on my shared network or via a wireless to connection in order to print to it from my laptop.
I have access to the desktop I believe the printer is routed to the server through and have "shared printer with network" via this computer. However, I still cannot find the LD145 icon on my macbook when I try to connect and print, even when going through the "Windows"-> (shared server) route. I've also installed apple's "general lanier printer driver" in hopes have luck finding the printer if I have the driver installed, but that has not worked either. How I can connect the macbook to the LanierLD145 via my wireless server connection?
Info:
MacBook Pro, Mac OS X (10.6.8)
I have a Linksys Wireless Router and a Linksys Modem, the router is 6 years old or so 802.11b, how much faster would the Internet be if I had a combined Linksys wireless router/modem versus the 802.11b that I have now?
Would I see a huge difference? I am running my Macbook off it and an olde Toshiba laptop.
I want to fully convert to the apple eco-system but can't afford the new airport extreme right now. Model number of the used airport is EbM8799LL/A
View 8 Replies View RelatedWhat is the best router to have for my iMac 27", 3.06 gig? I currently have a Belkin N1 Wireless Router, but it has been acting up lately, dropping my connection, requiring disconnect/re-connect.
View 24 Replies View RelatedI have a Netgear Wireless G Router and was wondering if this is sufficiant or is there something out now that is faster/better. Mainly used for my macbook and wife pc laptop and 2 IPhones.
View 4 Replies View RelatedI have just got my 1Tb time capsule and there are a lot of confusing descriptions of how to connect it.
At the moment I have just selected "join existing wireless network" which is a ADSL 2.4ghz G Router that came with my internet package (Thompson TG585 v7).
Does this mean that all traffic goes via the ADSL Router and that I will not be using the 5ghz band when I back up so that all the data will follow a path like this and have slow data rates? :
MAC --2.4ghz--> ADSL Router --2.4ghz--> TC
or will I be communicating directly with the TC at 5ghz for backups and data transfer and 2.4ghz with the ADSL router for internet like this? :
MAC --5ghz--> TC
ADSL Router --2.4ghz--> MAC
If this is not a good setup, what setup would allow me to get the full speed to the time capsule and be connected to the internet.
I have an airport extreme base station (wireless n draft). problem is, my room is all the way in the back and i get poor reception. Can i just buy another standard $40 wireless G router and "extend" my wireless network? if so, how easy would this be to accomplish? would it be as simple as hooking up the $40 router with my airport extreme using via ethernet cable so that it extends it? update: I am looking at this router...would this accomplish my purpose? [URL:....]
View 5 Replies View RelatedI have one of those USB dongles... i was curious if there are any wireless "G" or "N" routers that will work with it.
View 2 Replies View RelatedI got a new HP wireless printer, and the mac suggested setting it up with the USB first, and then disconnecting once it was configured. I did all that.The mac asked to choose a wireless network for the printer, I did. Then the set up CD asked me to add a printer to the qeue from system preferences from the menu- when I clicked my printer was already added. None the less I followed the direction, and then got the message "You already have a similar printer set up, would you like to add this too?" I clicked YES, and then continue.
When I clicked on continue, the set up cd (or mac) told me that I had NOT set up a printer from the Queue (sorry about spelling), even though I had. So when I clicked continue, it told me the printer was not recognized in the wireless network, and now I'm stuck with plugging it in the usb. Please I know this sounds confusing, but why is this happening and what do I do to get the mac to recognize my printer? Apparently its not.My wireless signal is fine, I checked.
So as the title states, I'm having trouble getting the wireless to work through Vista on my MBA.The router is a dlink DIR-615, supports wireless-N. It works fine when I'm in OS X. But when I'm in Vista, it shows up, but when I try to connect it won't work. Basically it just says it cannot connect to the router, and it tells me to select a different network.
Router settings on the DIR-615:
- mixed mode a/b/g/n
- channel 6
- WPA/WPA2 encryption
- AES cipher
I tried manually setting up the connection with the corresponding settings on the router through the settings, but no luck. I tried connecting to a different router, WRT-54G the popular linksys one, no problems with that.
Boot Camp drivers have been installed. Its weird, I had this problem setting up my PS3 (playstation 3) before; It would connect, but it was unable to access internet. I had to disable/enable the PS3 wireless system to get it working again.My sister has a macbook pro 12", and she hasn't had any problems connecting through OS X.I'm a first time Mac user, am I missing anything?
Can I connect a wireless router to the second ethernet port of my MacPro? I have the main ethernet cord from the modem connected to my ethernet port 1, then I connected my router to my computer through ethernet 2, thinking that it would broadcast the internet connection. However, it is not working. The router is broadcasting, but the internet isn't working (and the light indicating internet connection on the router is yellow, not green). Is this something that isn't possible? Or do I need to change settings (not just plug and go)?
View 9 Replies View RelatedI've got an iBook G3 with the B AirPort card installed that has worked fine until trying to connect it to the Linksys WRT610N. No matter what settings I use, AirPort cannot connect to the router. I've updated the router's firmware to the latest version, and am only using WPA, as WPA2 is not supported by the card. I've switch between TKIP and AES, which hasn't helped either. Also, I've changed the router between everymode (Mixed, Mixed B+G only, B only), and that hasn't worked either.
View 8 Replies View RelatedI have a D-Link Extreme router, and the WiFi has issues with my MacBook and such every so often and it drives me absolutely crazy. But I have 2 wired computers and a Xbox 360 that never have a problem plugged into the router via ethernet. I was wondering if I bought a Airport Express and plugged it into the 4th port of my router rather then into modem would it have enough juice to transfer the WiFi? I don't want to spend the extra money on a more expensive router for some plugs and WiFi if I can still use my router for wired and send a wire to the Airport for wireless. Yet I don't want to spend the money on the Airport Express if it can't be used like that like some other routers can.
View 2 Replies View RelatedI have macbook intel 2.0 GHz and Mac OS X 10.4.11.I had no problems with connecting with belkin g plus mimo router (f5d9230-4) before, but suddenly it dropped down the connection.It was about two months ago, in meantime I was trying to reset modem and router many times, I did "restore factory default" on the router and set it up again, I was trying to change location in network system preferences, but it doesn't work.I see my router as available in airport networks list, but I am not able to connect to it, it shows "password is not valid" when I'm trying to do it by network setup assistant, and "there was an error joining the airport network" when by airport scroll down menu.
I was also trying to set router as a open network, or to change the password.My other wireless devices like iphone 3g have no problems with setting up such connection, but my macbook must be wired if I want to access internet at the moment
OK I know this can be done and have searched many forums and I cannot find the whole walk through on the process!!!
I have the Airport Extreme one version back without the dual antennas and I'm trying to make up for that with my old linksys router. I want my airport extreme to transmit wireless N only! and my linksys to transmit wireless G only!! configuration setting to make this happen??
Not sure if this is possible, I'm sure there's someone out there who would be able to tell me either way. I've got a D Link router thats plugged into my 50mb in my lounge. I'd like to put my airport express in my kitchen and pair them so its the same network. The reason for this is that I have my HIFI in the kitchen which will be plugged into my airport so I can use it as remote speakers for my itunes while I'm still connected to the 50mb and D Link. Is this possible?
View 2 Replies View RelatedMy friend bought a new netgear router today. He plugged it in and was ready to get on the internet. The problem is, he can't get on the internet. He is able to connect to the router though. We also tried unplugging the router from the modem and plugging the ethernet straight into his Macbook Pro. From there the internet works perfectly. It is like the modem and the router are not connecting.
View 1 Replies View RelatedI have just purchased a new Time Capsule but struggling to set it up in the most effective manner. I currently have a Belkin Wireless Router / Modem that I was using to provide me with internet connection and my home wireless network.
Now I have the TC, I want to use that for my home wireless network but I will need to still use my Belkin router / modem to provide me with the internet connection.
Is there a way I can disable the 'router' element of the belkin unit and just use it as a simple ADSL ethernet modem to connect to my TC and then let the TC set up the network?
