I'm trying to install this hard drive in my Powermac. Here's the drive I'm considering installing:
[URL]
Will it work with my "Ultra ATA" Interface or will I have to buy a SATA card?
i was wondering if my dual 2.0 ghz g5 supported the sata 300 hard drives?
View 11 Replies View RelatedLooking for a good PCI (32 bit) esata controller card for my G5, im considering these two cards but dont wanna shell out the cash $110. I want a card that can handle more than 4 drives, RAID 0,1 and 5 compatible. [URL:...] The sonnett card is waaaaay to expensive... But, the Off brand card is more like what im looking for just needs to be $30 cheaper. PCI-X will work too, because its backward compatible with 32Bit PCI
View 3 Replies View RelatedDo i need a Raid card to install a SATA hd for this model (quicksilver). Or can i just get a converter cable (IDE ATA-to-SATA).
View 3 Replies View RelatedI have two drives in my Quicksilver 2002 G4, one is a 250GB which can be fully used, the other an 80GB. Can U rid both of these drives and install two SATA 1.5TB drives? I do not want to use the PCI slots for a SCSI card and wire additional drives that way, because the transfer speed will be limited to 40mbps I believe. I have a Sonnet card a dual PPC 1,8Ghz card, a PCI USB 2.0 card and have other open PCI slots, but finally ran out of storage, and have a use for this machine to hold a LOT more. Other than the transfer speeds possible on SATA, are there any other differences between the original IDE (ATA) drives? Do they connect the same way?
View 9 Replies View RelatedI had the brilliant idea of trying a clean install of OS X on my circa 2002 iBook. I had Tiger on there, but the iBook was quite sluggish and I was getting frustrated with the performance of the iBook on the only thing that I wanted it to use it for: the internet. So I thought that if I wiped the hard drive and installed OS X again, I could benefit from erasing an accumulation of junk on the iBook. (One thing to note is that the hard drive is actually from a clamshell iBook. The hard drive stopped working a few years ago, and I spent a weekend replacing the drive)
The combo drive has long since stopped working on the iBook, so I hooked up the iBook to my MacBook via firewire and erased the hard drive. But like an idiot I installed 10.5 instead of 10.4 and now the iBook only returns the folder with the question mark. I have not had any luck (either before the ill advised OS X install or before) with doing a remote install. I have the original disks that came with the iBook (10.1), but when I try to install them using the MacBook's drive it just tells me that I can't install it on my MacBook, which is not what I want to do.
I have installed 2 extra hdd's in my 2008 mac pro using the 2 extra sata ports. I was wondering if it would be possible to install a sata controller in the mac pro to increase my sata ports so I can add 2 more sata drives instead of the remaining optical drive. And if I can where would it go.
View 6 Replies View Relatedis installing an ssd into a mini the same as a regular sata drive? i had some problems with a mini upgrade, wondering if i did something wrong during the hdd upgrade
View 2 Replies View Relatedlooking at installing an OEM SATA hard drive into an OWC Mercury Elite-AL enclosure. Do I need a ribbon cable and screws? If so, could anyone recommend a brand of cable and tell me what size screws I would most likely need?
View 1 Replies View RelatedI am looking for a tear down guide for my 4 core power mac. I need some instructions on how to remove the CPU's since I bought this for $100 and found the part for $250.
View 2 Replies View RelatedI have a 13" MacBook Pro 2011, 2.3gHz, 320GB. What connector does it have? And would SATA still work with my laptop? One more question, what are the exact dimensions of the hard disk drive bay in my laptop, the manual only says 2.5".
Info:
MacBook
Pro, Mac OS X (10.7.2)
My G4 MDD (1.25 CPU, 2G RAM, OSX 10.5.8) needs a new drive.
I'm told SATA drives are the thing to get.
I don't know what a SATA drive is, or whether it is compatible with my machine.
I have a g4 quicksilver and I bought a 1TB sata hard drive to put in it. I also bought a pci card to connect the sata harddrive. I disconnected my other hard drive and put in the OS X disc to load the operating system, but when I get to the screen to choose which disc to install it on, my hard drive doesn't appear.
View 4 Replies View RelatedI like eMacs but the G5 looks sooo nice. I know I probably won't be able to use any for very long but whatever. What is the best?
View 24 Replies View RelatedI have a PowerMac G4 (MDD 2003, I believe) that I use as my home media server for my Apple TV. Currently I have a 14+14GB boot RAID and 75+75GB storage RAID, using old PATA drives, of course. This is working great and is pretty well performing so far, but I'm going to run out of space eventually since I'm a packrat. I'm thinking that this Christmas will be a good time to renovate this machine, so here's the question MacRumors: What's the best SATA controller for my machine? PS: It's a dual 1.25GHz PowerMac 3,6. In MacTracker, this matches 3 different machines. Is there a way to find out which one this truly is?
View 3 Replies View RelatedWhat is the best way to go about this? I have seen some on Amazon that are dirt cheap but I don't know if they work. This is kinda off topic but will this work with a g4 AGP?
USB 2.0: [URL]
Gigabit Ethernet: [URL]
Since installing SL last Friday, every time I restart my computer, SL thinks it sees a dual monitor set up. I only have one monitor. It's really getting annoying because I lose my mouse pointer in empty space where SL thinks there is a second monitor. I'm not sure how to remedy this situation.
View 1 Replies View RelatedI was wondering if my dual 2.0 ghz g5 supported the sata 300 hard drives?
View 1 Replies View RelatedMy SATA RAID card is conflicting with my 6800 GT Graphics card in my 2002 Quicksilver.
View 7 Replies View RelatedI am buying a used Powermac, G5 Dual 2GHz. It already has a SATA 320GB HD in it but I want to use my SATA 160GB from my dead iMac. The only questions I have are:
1. Is there anything special I need to do installing the second SATA drive? Does the drive need to be set to Slave or Cable Select?
2. Because the 160GB (going to use for storing musc) drive has OS X Tger installed, will it be a problem when booting once I install both drives? The 320GB drive has Leopard (This will be my primary drive). Will it boot to Leopard and let me use disk utility for format the 160GB drive?
I have a MacBook Pro with a 128GB solid state. Is this SATA II or SATA III?
View 3 Replies View RelatedIm considering purchasing a higher capacity internal hardrive around the 750Gb/1Tb mark. However my macbook is the early 2008 model, and it seems the majority of hardrives are SATA II, having speeds of 3Gbt, which my mother board may not be capable of (apparently only 1.5Gbt) From researching and reading some reviews of others who have purchased internal drives on Amazon UK, some have had difficulty due to this problem, but have been able to fix the issue with a firmware update reducing SATA II drive speeds to 1.5Gbt.
Questions I have: Do all SATA / SATA II internal hardrives need a firmware update if replacing on to a new computer?(If so, would I need to look for a specific firmware update for the specific drive I intend on buying? And if you're in the knowledge would you mind posting links to these updates?)What is the process of updating the firmware i.e. would I need to put firmware on external usb hardrive 1st, then upload it to macbook after installing new internal drive (if it boots up my OS that is) etc. Would a 'hybrid' (disk+solid state) drive be compatible with a macbook as old as mine?Do I need to update my operating system to OS X Lion first, or can it be done after installing the drive?
my current laptop hardware:
Macbook Pro 15.4" (Early 2008 Model)
Intel Core 2 Duo 2.4Ghz ProcessorGeForce 256Mb 8600M GT Graphical Processor
Intel ICH8_M AHCI 1.5 Gbt MotherboardToshiba MK1655GSXF 160Gb 2.5" Hard DriveOperating System: OS X Leopard 10.5.8
Info:
MacBook Pro, Mac OS X (10.5.8), 15.4" 2.4Ghz (Early 2008 Model)
I have a Dual 1.8 GHz PowerPC G5 with 2.5 GB of RAM. My fan starts revving really loud when I am using multiple apps (Adobe CS2, Firefox, iTunes) and while watching a video tutorial or AVI movie (both saved on my desktop). It also happens when I am just watching a AVI movie with no other apps open.
I just added one GB of RAM yesterday thinking maybe this will solve the problem since I am running multiple apps. This did not resolve it. So I searched the messageboard for threads on fan issues similar to mine. I read it may be caused by the tempature in my room. I keep the tower on my floor on top of 2 pieces of wood about a 1/2 inch thick. I live in a small brick studio apartment so the tempature is usaully between 60 to 70 degrees.
I looked into smcfancontrol but it looks like its for laptops only.I also do not have a utilities program for my computer yet. I was wondering what was the best program out there to clean up/tune-up my hard drive so its running at maxium speed.Has anyone had experince with this issue and have any answers? I am concerned this may be very detrimental to my computer in the long run.
I've bought my 13" MBP (love it) but need to dual boot to run some programs, so I bought the Windows 7 Prof 64bit Upgrade. Now... because it's the upgrade version do I need to have a previous version of a Windows OS installed before I can upgrade or can I install straight away? Another question, at some point I'm tempted to upgrade to the 500gb Momentus XT. Will my Windows 7 disk be okay for multiple installs?
View 11 Replies View RelatedI curently have 10.3.9 with a PowerPC G4 dual w/ 1.25 processors and 2 gig of ram. I want the highest upgrade I can get that will be compatibe with my software which is:
Quark 6.5
Acrobat 7.1
Acrobat Distiller 7.0
Illustrator CS1
Photoshop CS1
Microsoft Office (don't know what version but I've had it for years)
I really can't afford to go buy all the software again and I don't want my system to crash. Any suggestions?
This upgrade is mostly spawned due to the recent purchase of a new iPod Nano... Not supported by my current OS! Man, I didn't read the requirements, shame on me. However, the dang thing will work on my kid's PC w/ XP Pro. I only got the Nano cause it's mac - he wanted the Zune that ONLY works w/ PC.
I'm looking for a new HD to replace the original, now failing Maxtor drive in my G5 tower (1.8 Ghz dual processor, purchased in Aug. 2004), and have just about settled on the Western Digital Caviar SE16 series. It seems there are two types -- SATA and SATA II -- and I'm not sure about how to make a decision on which particular WD model to buy.
Will either type work in my machine? Or would the SATA II have potential compatibility problems? I read somewhere in these forums that someone with a G5 had bought an SATA II drive, and it wouldn't run with his system. (He said he had to reset some jumper switches to reduce the transfer rate of the drive ??, but now I'm told elsewhere that SATA drives don't have jumper switches.
Information:
1.8 DP G5, 1.5 GB RAM w/ Superdrive
Mac OS X (10.3.x)
I have ordered my first Mac, a Mini 2.66Ghz and I will put a Intel X25-M SSD in the machine to speed it up further. I hope I will be pleased with it
However, the question I encountered was whether the sata connection in the Mini is SATA-150 or SATA-300? Does anyone know?
I am now shopping for a new internal HD of MAC G5; previous HD died. I have decided on a Western Digital and was about to order one when I became alarmed by the SATA II listings. Is there a difference between SATA and SATAII that I should be concerned about the comptability? Don't want to get it and find out it doesn't work!
View 3 Replies View RelatedLooking to buy a used G5. Dude said he upgraded a G5 1.8 to a Dual 2.0... Is that even possible and if so what limitations or problems could the machine have. Said he replaced the whole motherboard.
View 7 Replies View RelatedI'm finally upgrading my iBook, but I'm slightly confused on which type of RAM to buy. According to my System profiler, I would need SO-DIMM SDRAM type with PC133 speed. I can find the SO-DIMM SDRAM, but the speeds are not matching (PC2700 and PC5300).
View 1 Replies View Related