I noticed that when I restarted my MacBook today, the Apple logo takes a while (20-30 seconds) to just show up before the spinning gear shows up.
Things I've tried
1. Repair disk permissions
2. Verify disk
3. Reset PRAM
4. Boot into Safe Mode
5. Make sure Mac OS X 10.6.5 is the startup disk
So I just bought a Seagate momentus XT HDD for my 2010 i7 15" MBP. I clonded the drive using Super Duper from the old drive (500GB Toshiba) to the new drive using a USB SATA enclosure.
I now have the new drive installed. Once the Apple logo shows up it boots very fast, but it takes like 30 seconds for the logo to show up almost as if it is having trouble finding the boot drive.
I have run Onyx's full automated service whihc verified startup disk, verified and repaired permissions, emptied caches, etc.
Instead of showing white screen with an apple logo it became black screen instead but still can be log on to the desktop but ican't press alt to use bootcamp because the screen is all black TT?
Info:
MacBook Pro, Mac OS X (10.6.8)
So this morning i turned on my alu macbook (2.0ghz, 2gb ram) and i'm stuck on the apple logo and spinny thing at the bottom, i've searched here and the apple site but can't find a solution.
View 24 Replies View RelatedI have a major problem with my first Generation MacBook Pro. It won't boot anymore: it just turns on and gets stuck at the Apple logo. There is no spinning wheel and nothing else happens. Pressing 'C' for booting from CD or pressing ALT and choosing the CD as an alternative boot source does not work either: it just does exactly the same, gets stuck at the apple logo. I already tried resetting the PRAM and NVRAM, as well as the SMC. This also did not change anything. CMD+V mode starts up then stops at the line "ACPI: System State [S0 S3 S4 S5] (S3)"
What can I do? I really need to save my Mac, there is some really important stuff on there
It is getting stuck on the Apple Logo in white page with spinning gear. The apple logo keep disappearing and come again endlessly.
Info:
MacBook Pro, Mac OS X (10.0.x), Actually I only know it is OS X.
My daughter's 3 year old MacBook Pro will not boot up. The grey screen with Apple logo comes up and it looks and sounds like it is going to boot up but after 30 seconds it goes black and turns off.
Info:
MacBook Pro (15-inch Early 2011), iOS 5.0.1
My mid 2010 iMac i7 will not boot past the apple logo? I'm running 10.7.3. I have tried restoring from TM backup from recovery mode (worked the last time this happened) however upon completion it returns to the recovery screen? I made a disk of Lion when I downloaded the first time (followed same instructions sourced from numerous websites) which does not seem to work when i set to start up from this disk, just gets to the grey screen and flicks between the apple logo, a folder icon with a question mark and the circle with line through? Now I can't eject the disk either, a message appears that system can't eject and to make sure all applications are closed? Not sure how to go about closing these applications without being able to start the system? When I tried booting from the Macintosh HD I got a message that the boot cache partition was faulty? I have ran disk permissions etc all ok.
Info:
iMac, Mac OS X (10.7.3)
My mother's unibody white MacBook will not get past the grey apple and spinning gear when you first boot up the computer. This was after she opened a link in an email from a friend who had her email compromised. Now I'm getting spam emails with the same link from my mother's hacked email, and her computer won't even get to the login screen. I took it to the genius bar only to be told it was likely HD failure, but the windows partition works without a hitch! What could this be? A trojan? Is there any way to retrieve data (really just pictures) before I attempt to reinstall OS X?
Info:
MacBook, Mac OS X (10.6.8)
Macbook: A1181 Core 2 Duo 2.0ghz 1GB RAM
DVD disk: Leopard 10.5 Retail install
Hard drive: dead (spins with clicks).
With regular startup I get the flashing question mark and can hear the failed hard drive click and spin. After getting the DVD to boot in the drive (it doesn't suck it in right away), I get an apple logo and pinwheel like I should, but after about 30 seconds it goes to a black (blank) screen and the DVD spins down, but not all the way. The computer is still on, but nothing happens.
Oddities:
<>If I start it with an iMac 10.4 DVD I can boot to the install screen just fine, but can't install because it's an iMac DVD. I can erase and partition the drive fine (not the dead one, another one I have).
<>Safe mode boot does the same thing, but takes 20 times as long to boot
<>Retail OSX 10.4 DVD does not boot at all, but that one might be for PowerPC computers. I get the flashing question mark folder.
My MacBook Pro will not boot up any more. It just suddenly happened. It turns on and comes up to the gray screen with the apple logo and then the circle progress icon comes up and spins.
View 1 Replies View RelatedI've been reading this site for a while now, first time I'm posting. I recently purchased 8 GB of RAM for my 2010 13" MBP. There are two 4 GB DDR3 PC3-10500 1333mhz sticks. When I install them in the laptop my computer does not get past the apple logo boot screen (the spinning disc freezes). However, I can boot into Windows (boot camp) without issues.
Also, when I pair either of the 4 GB sticks with one of my old 2 GB stock sticks the laptop boots up fine in OS X. The system profiler registers it as 6 GB of 1067 mhz RAM (the stock sticks are 1067 mhz)
My macbook is driving me insane now. Just recently, my macbook has occasionally flickering screen and freezes after that. Yesterday, when I was watching youtube on fullscreen, it first has flickering screen, then freezes. So I hard booted it pressing the power button. Then, when I try to restart it, it won't boot pass the apple logo no matter what. Here's my macbook spec2007 Summer Macbook Pro 15"Snow Leopard 10.6 OS XI cracked my screen once, and got a replacement, don't know if that matters.
I've tried the following:Safe mood reboot, the progress bar goes about half, then disappears and stalls again.Booted in verbose mode but it gives a warning message: 'com.apple.driver. internal modem support declares no kernel dependencies; using com.apple.kernal.6.0'. Booted in Single user mood, and typed fsck for disk repair. After checking said the volume Macintosh HD appears to be ok. But still won't boot pass the apple logo after restart.Boot with installation disk pressing C at startup.
Success after a few try: Opened Disk Utility and did disk repair (no problem found). Reinstalled Snow Leopard OS X 10.6. This time it booted with Finder and everything for a short while, then the screen flicker and freezes again (before I can backup anything!). Then, I can't reboot pass the apple logo again. When I try to reinstall Leopard OS X 10.5 with installation disk, the macbook seems to try to read the disk, but won't boot. I've got a CD stuck in the optical drive now.
Info:
MacBook Pro, Mac OS X (10.6.7), Bought 2007
This morning, I would turn it on and it'd go to the grey screen with the Apple logo for a few seconds and then go to the icon that is a circle with a line through it. After reading online, I was able to boot it up in Safe Mode. I went to Startup Disk in Preferences. I chose the MAC OS X, xxxx and then clicked the lock to prevent further changes and then clicked restart. Now when I turn on the macbook, it goes to the grey screen with the Apple logo for at least two-three minutes and then just shuts off. Won't boot into Safe Mode now. I already tried the Command-Option-P-R keys trick like five times.
Info:
MacBook Pro
For several weeks, my black MacBook (2008) has been acting odd. Certain applications won't open, and when I attempt to open them, the computer makes a quiet clicking noise, like the drive is failing. Last week, when trying to boot it, the thing just wouldn't. Stuck on the grey Apple logo screen. Assuming a hard drive problem or failure, I ran the tests. I ran Disk Utility from the Snow Leopard install disk, checked & repaired permissions, checked & repaired disk. All okay. I ran the Apple Hardware Test from the install disk that came with the computer, using the test that runs for an hour or so, and all appears to be fine. The computer won't boot into safe mode. I've tried flashing the PRAM. I doubt I could achieve much through target disk mode, as I've already run Disk Utility. What's left to do? Something doesn't add up here.
View 1 Replies View RelatedMy circa 2006 Intel-processor iMac does not get beyond the white screen with the Apple logo and the spinning wheel when I power it on. As per other support documents (Article: HT1533; discussion "Mac doesn't boot") I have tried and SMC reset, all of the keyboard controlled reboot options (with no response - and now a disc is stuck in the optical drive), reset the RAM, etc. Apart from taking it to my trusty local Apple store
Info:
iMac, Mac OS X (10.6.8), Part of an Apple home/business net.
I've set my monitor (Dell S2409W) to portrait mode by setting it to 270 degree rotation in System Preferences/Display, and everything is fine but during boot the gray screen with Apple logo is shown in landscape orientation (so the apple "bite" is pointing to the top) and also not filling the whole screen (i.e. the gray screen is properly aspected at 9:16 as if to fill the screen in portrait mode but the whole thing is rotated 90 degrees).
Is there a way to fix this annoying problem?
I'm using Mac mini with OS X Server Snow Leopard.
I'm trying to repair a Powermac G5 (dual 2.0, the first model I believe, with a new Radeon 9800 graphics card) that won't boot and I'm having some problems that I can't seem to diagnose.
The machine will boot to the openfirmware prompt or target disc mode and will show the 'OS not found' icon if left to boot from the HD (which has been wiped). If I try to boot from either the included restore disc or a retail 10.4 DVD I've tried it will show the boot screen with the Apple logo on it but no spinning status indicator underneath. It just freezes on that screen. Once it showed the status indicator but it just continued to spin for about 30 mins, at which point I gave up. Same issue if I try to boot the hardware test (except it freezes on the hardware test loading icon rather than the Apple icon). The superdrive appears to work as it is accessible in target disc mode.
I've reset the SMU and reset the PRAM via the keyboard shortcut. The one thing that leads me to think it's a firmware fault is that when I run the 'reset-nvram' command it gives an OK, but when I then run 'reset-all' it freezes rather than rebooting. Any ideas anyone?
Information:
Powermac G5 Dual 2GHz
i'm trying to boot from the Snow Leopard install disc so I can format my drive and re-install, however... it just gets stuck on the white screen with the grey Apple logo, what's up with that?
View 5 Replies View RelatedI have Time Capsule and everything is backed up on there. My data is on a separate USB HD + Drobo, but for now I need my iMac to boot but it won't. It won't even get into the Desktop. all the guides online says double click the Install Icon this and that...I would if I can get into the Desktop !
It is just stuck on the Apple Logo screen with the spinny thing, that stops spinning!
After recently doing a fresh install of Snow Leopard, it was working great for about a week, and now it hangs at boot and flashes the Apple Logo, a NO sign, and a folder sign. I booted in verboose mode and it say that it could not load drivers.
I had this problem before and I used Leopard's (10.5) Archive and Install feature to fix it.
Where is this located on SL (10.6) ? I DO NOT want to loose my data
Sometimes, when I turn on my iMac (10.6.2), the system will not load, you can see the grey screen but empty, no apple logo there. I have to force a shutdown pressing the power button and when I turn it on for the second time it will work properly.
It only happens once in a while but I cannot understand why, since nothing changes.
PS.- I have verified my disk with the disk utility and everything seems fine.
there back in September when I got my macbook I had the problem where it wouldn't boot past the apple logo screen and it was taken away and the hard drive had to be replaced and now it has happened again! I'm so annoyed as Im getting really close to exams at Uni so need my computer but will it need to have the hard drive replaced again!? As well with it being Lion I dont have a disk with it to try utility disk.
View 5 Replies View RelatedI've checked disk permissions, run SMART check. the disk seems fine but the problem persists. It began a few days ago.
Info:
MacBook Pro (17-inch Early 2009), OS X Mountain Lion
My PowerBook G4 (Ti, 867MHz) just decided it didn't want to boot today...
The PowerBook has been asleep and not used for a few weeks. I woke it up last week for a few minutes to try and print out a document. It restarted just fine after installing the printer driver. Then it went back asleep until today.
I decided I had better shut it down as it has been sleeping a lot. It's shut down for about 5 minutes when I boot it back up to find it stuck at the Apple logo with the (spinning) spinner. What I tried to do to solve the problem:
1. Booted into Terminal mode (command-s) and typed exit so I could see the boot log. It appears to attempt to boot yet repeatedly prints:
> localhost /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[92]: Login Window Application Started -- Threaded auth
> localhost loginwindow[92]: _RegisterApplication(), FAILED TO establish the default connection to the WindowServer, _CGSDefaultConnection() is NULL.
[Code] ....
2. Booted into Terminal again, and mounted the volume. I was able to do ls to list the file contents - so I CAN get to my files. It's not a disk issue. Then I ran fsck -fy. It reported the disk as OK.
3. Rebooted and reset PRAM. No change
4. Reset NVRAM. No change.
5. Popped in the Leopard install disc and restarted. Booted into Leopard disc.
6. Tried to repair permissions from Leopard disc - it just hung and I had to cancel the process.
7. Verified disk from Leopard disc. Reported as OK.
8. Clicked the next button on the install screen. Tried to install. "You don't have enough space"... The skimpy 40GB HD is so packed with stuff that it can't install. And my external HD won't connect to it, it never shows up. Not like I can move off anything anyway as it won't boot...
I CANNOT format the HD. I have stuff on there I can't lose. Does the Terminal recognize and mount USB devices so I can copy from the Terminal? If not I guess I could delete some apps and Xcode and stuff, maybe the System folder...
I had been using my iMac all night, when all of a sudden the bouncing beach ball appeared and everything became unresponsive, apart from the mouse cursor itself. It might be worth noting that a few hours prior to this, I plugged in an external hard drive to burn off a DVD. This external hard drive has two partitions, the first being a restored image of Leopard; and the second, my out of date backup ("yes, I know").
I subsequently restarted my machine, enjoyed the chime, pondered the excessively long start up and looked bemused at the Leopard Setup wizard. I realised that the restored Leopard partition had booted up instead of the internal disc. So, I unplugged the external drive, pressed reset on the iMac and was immediately greeted first by the reassuring chime, then by the Apple logo and a lingering grey screen and finally by a flashing dark folder icon with a question mark in the centre for eternity.
I tried rebooting a few more times. Same. I've been frantically Googling but only found the PRAM reset and a very frightening iMac disassembly guide. I've tried plugging the external drive back it, but it refuses to boot Leopard from that now. What can I do? I feel so helpless on a Mac, on a PC I'd at least be able to open the sucker up before panicking! I've been working on a client's flash web dev project for months, and not made a back up in about half that time. The website is supposed to be going live tomorrow! Luckily I have the site uploaded, but the entire source code is potentially lost, so in the long term this is a major catastrophe!
So, today I tried to install windows through boot camp assistant on my mac. When it got to partitioning my drive I got an error that my hard drive needed repairing. So I opened up disk utility and clicked verify disk (I can't click repair) and got this error Disk Utility stopped verifying �Chris Hard Drive� because the following error was encountered: Filesystem verify or repair failed. I then researched this and learned to fix the problem I must boot from my leopard install disk and use the DU from their. Unfortunately I don't have access to the disk. But I have the install disk from my old macbook (the white one) so I used this. I put in the disk and shut down. When I turn it on I hold C but all I get is a grey screen but with out the apple logo. When I try turning it out holding alt I don't get the option of the CD just Chris Hard Drive. But when I boot up holding D i do get to the hardware test screen but I get the error that's something like "Hardware test does not support this hardware". Will the Leopard install of a different type of macbook not work on my new macbook pro (13" aluminium)?
View 1 Replies View RelatedMy intel mini (2008, I think) won't boot. I ran Disk Utility and then Disk Warrior from my Macbook Pro, then I tried single-user mode. Everything came back "OK" but it still won't boot. It gets to the Apple logo with the spinning gear, spins 1-2 times, then freezes. It just sits, frozen, until I hold the power button and force it to turn off.
View 3 Replies View RelatedI own an iBook G4. I could not get it to boot up, it would just go to a grey screen with the apple symbol and a timer/clock that looked like a gear.FYI: I may provide more information than necessary in the text below. I'm not sure what is and isn't relevant.
Following some advice I found in this forum I got out my old OS disks to boot from the disc instead of the hard drive. I intended to archive the old hard drive and install my latest OS (10.4.6 on the disc, 10.4.11 was the version I had been running on the machine, I believe). The machine told me it needed 4.5 Gb to install 10.4.6 Tiger, but I only had 4.0 Gb left on the hard drive. So instead, I archived and installed with the OS that came with the computer originally, 10.3.4.
I got things going, did the archive and install, and got to the log in screen. Unfortunately, I could not remember the password, so I booted up in single user mode, and entered the following to get into the machine:
1. mount -uw /
2. rm /var/db/.AppleSetupDone
3. shutdown -h now
This got me in with a new admin login, and I started up in 10.3.4. I soon noticed that I could still see all of the files that I put on the hard drive on my old operating system. I thought I shouldn't be able to see them, but since I could I decided to try to copy them to an external hard drive. When I did, I got an error message saying that there was a read/write error. I was not entirely surprised, but I decided it was time to turn back to the forums for help.
What I want to do is copy everything from my old hard drive onto an external hard drive, make room on the iBook hard drive to reinstall my latest operating system (10.4.6). Once I've done that I'd like to get the essential files back onto the iBook from the external hard drive and continue using my computer (even though it is a dinosaur).
Reset my disc permission is Disk utility ...like the idiot i am, and now My MBA won't boot past the Apple logo and spinning cog. In Single User Mode the key problem seems to be. sudo: /private/etc/sudoers is mode 0666, should be 0440 :/ root# sendmail: warnibg: valid_hostname: empty hostname sendmail: fatal: unable to use my own hostname / is it possible to repair permissions in Single User mode?
View 24 Replies View Related
