After recently doing a fresh install of Snow Leopard, it was working great for about a week, and now it hangs at boot and flashes the Apple Logo, a NO sign, and a folder sign. I booted in verboose mode and it say that it could not load drivers.
I had this problem before and I used Leopard's (10.5) Archive and Install feature to fix it.
Where is this located on SL (10.6) ? I DO NOT want to loose my data
I've been reading this site for a while now, first time I'm posting. I recently purchased 8 GB of RAM for my 2010 13" MBP. There are two 4 GB DDR3 PC3-10500 1333mhz sticks. When I install them in the laptop my computer does not get past the apple logo boot screen (the spinning disc freezes). However, I can boot into Windows (boot camp) without issues.
Also, when I pair either of the 4 GB sticks with one of my old 2 GB stock sticks the laptop boots up fine in OS X. The system profiler registers it as 6 GB of 1067 mhz RAM (the stock sticks are 1067 mhz)
Macbook: A1181 Core 2 Duo 2.0ghz 1GB RAM
DVD disk: Leopard 10.5 Retail install
Hard drive: dead (spins with clicks).
With regular startup I get the flashing question mark and can hear the failed hard drive click and spin. After getting the DVD to boot in the drive (it doesn't suck it in right away), I get an apple logo and pinwheel like I should, but after about 30 seconds it goes to a black (blank) screen and the DVD spins down, but not all the way. The computer is still on, but nothing happens.
Oddities:
<>If I start it with an iMac 10.4 DVD I can boot to the install screen just fine, but can't install because it's an iMac DVD. I can erase and partition the drive fine (not the dead one, another one I have).
<>Safe mode boot does the same thing, but takes 20 times as long to boot
<>Retail OSX 10.4 DVD does not boot at all, but that one might be for PowerPC computers. I get the flashing question mark folder.
So, today I tried to install windows through boot camp assistant on my mac. When it got to partitioning my drive I got an error that my hard drive needed repairing. So I opened up disk utility and clicked verify disk (I can't click repair) and got this error Disk Utility stopped verifying �Chris Hard Drive� because the following error was encountered: Filesystem verify or repair failed. I then researched this and learned to fix the problem I must boot from my leopard install disk and use the DU from their. Unfortunately I don't have access to the disk. But I have the install disk from my old macbook (the white one) so I used this. I put in the disk and shut down. When I turn it on I hold C but all I get is a grey screen but with out the apple logo. When I try turning it out holding alt I don't get the option of the CD just Chris Hard Drive. But when I boot up holding D i do get to the hardware test screen but I get the error that's something like "Hardware test does not support this hardware". Will the Leopard install of a different type of macbook not work on my new macbook pro (13" aluminium)?
View 1 Replies View RelatedAll I get is the grey screen and the little circle with the rotating fan blades. Then they stop spinning and it just hangs.
I cannot boot up. Is this a bad hard drive? Are there other keys I could hit to make something work?
Info:
MacBook Pro, Mac OS X (10.6)
The little progress spinner thing below the apple just spins and spins. The computer said that several apps stopped responding and had to quit after falling asleep watching a movie in VLC, which had error logs that had frozen on the screen as well saying, "Computer too slow?" from dropped frames apparently. Not normal. Also, yesterday, when waking it up from the display shutting down, the whole screen was gray and smeared looking. There was nothing recognizable at all on the screen, and I hit the power button quickly for it to sleep, and back again and it worked fine for the rest of the day. Its a 1.66 Core Duo Mac mini w/ 2gb of RAM.
View 8 Replies View RelatediMac Intel G5 stuck at apple logo.
Info:
iMac, Mac OS X (10.6.8)
I was installing the Mac OS X Snow Leopard (family pack), haven't installed yet, due to a moving from USA to Brazil. I put the CD on and followed the instructions of installation. After is ready to install, a message showed that would take about 1 hour and 45 minutes. So I left the room and when I came back the screen was bright with an "apple" on it, and its frozen, and I can't take the CD from the slot or do anything in the computer. What that means, did my laptop crashed? I did turn the power off and turn back on, but still the same.
Info:
Mac OS X (10.5.8)
I just bought a new 27" iMac and when I start it up I get a white progress bar under the apple logo. When it does come up, iTunes will not play and sometimes the computer will not recognize the magic mouse or my WiFi. Everything works fine after I re-start.
Info:
iMac, Mac OS X (10.7.4)
Pretty smooth sailing until I had to reboot my mac pro. It just stops at the point where you have the grey Apple logo and the spinner.
My computer displays grey screen and apple logo for 10 minutes or more during start up and shut down. Sometimes it refuses to shut down. This issues started after installing OS lion. What do I do?
Info:
MacBook Air, Mac OS X (10.7.3)
I just tried to upgrade my iMac to snow leopard (10.6.3) from cd.It remains stuck on the start page since hours : white page with grey apple logo and no spinning wheel or progression bar.
Info:
iMac
Why is my Snow Leopard OSX 10.6.8 IMac screen all white when I turn it on? There is no spiral and no Apple logo and the desktop does not appear. The screen is just white.
Prior to this, we had a wind storm in our area with some power glitches today. After one of them, the dock items disappeared and just the wallpaper was there. The colored spinner began going around when I clicked on the mouse but nothing was happening. I unplugged it to try to reset it, but now the screen comes up all white, there's no apple logo that appears at start up and that's it. Now what should I do?
Info:
iMac, Mac OS X (10.6.8)
I am trying to install leopard on an older macbook (white version) which has 10.4.something. I plop the dvd in, it recognized the dvd I double click and hit install, it asks for password and restarts. When it restarts it hangs at the screen where the apple logo is and the circle below it just rotates. It doesn't start to install.
View 4 Replies View RelatedMy mid 2010 iMac i7 will not boot past the apple logo? I'm running 10.7.3. I have tried restoring from TM backup from recovery mode (worked the last time this happened) however upon completion it returns to the recovery screen? I made a disk of Lion when I downloaded the first time (followed same instructions sourced from numerous websites) which does not seem to work when i set to start up from this disk, just gets to the grey screen and flicks between the apple logo, a folder icon with a question mark and the circle with line through? Now I can't eject the disk either, a message appears that system can't eject and to make sure all applications are closed? Not sure how to go about closing these applications without being able to start the system? When I tried booting from the Macintosh HD I got a message that the boot cache partition was faulty? I have ran disk permissions etc all ok.
Info:
iMac, Mac OS X (10.7.3)
My circa 2006 Intel-processor iMac does not get beyond the white screen with the Apple logo and the spinning wheel when I power it on. As per other support documents (Article: HT1533; discussion "Mac doesn't boot") I have tried and SMC reset, all of the keyboard controlled reboot options (with no response - and now a disc is stuck in the optical drive), reset the RAM, etc. Apart from taking it to my trusty local Apple store
Info:
iMac, Mac OS X (10.6.8), Part of an Apple home/business net.
So this morning i turned on my alu macbook (2.0ghz, 2gb ram) and i'm stuck on the apple logo and spinny thing at the bottom, i've searched here and the apple site but can't find a solution.
View 24 Replies View RelatedI've set my monitor (Dell S2409W) to portrait mode by setting it to 270 degree rotation in System Preferences/Display, and everything is fine but during boot the gray screen with Apple logo is shown in landscape orientation (so the apple "bite" is pointing to the top) and also not filling the whole screen (i.e. the gray screen is properly aspected at 9:16 as if to fill the screen in portrait mode but the whole thing is rotated 90 degrees).
Is there a way to fix this annoying problem?
I'm using Mac mini with OS X Server Snow Leopard.
I have a major problem with my first Generation MacBook Pro. It won't boot anymore: it just turns on and gets stuck at the Apple logo. There is no spinning wheel and nothing else happens. Pressing 'C' for booting from CD or pressing ALT and choosing the CD as an alternative boot source does not work either: it just does exactly the same, gets stuck at the apple logo. I already tried resetting the PRAM and NVRAM, as well as the SMC. This also did not change anything. CMD+V mode starts up then stops at the line "ACPI: System State [S0 S3 S4 S5] (S3)"
What can I do? I really need to save my Mac, there is some really important stuff on there
It is getting stuck on the Apple Logo in white page with spinning gear. The apple logo keep disappearing and come again endlessly.
Info:
MacBook Pro, Mac OS X (10.0.x), Actually I only know it is OS X.
My daughter's 3 year old MacBook Pro will not boot up. The grey screen with Apple logo comes up and it looks and sounds like it is going to boot up but after 30 seconds it goes black and turns off.
Info:
MacBook Pro (15-inch Early 2011), iOS 5.0.1
I'm trying to repair a Powermac G5 (dual 2.0, the first model I believe, with a new Radeon 9800 graphics card) that won't boot and I'm having some problems that I can't seem to diagnose.
The machine will boot to the openfirmware prompt or target disc mode and will show the 'OS not found' icon if left to boot from the HD (which has been wiped). If I try to boot from either the included restore disc or a retail 10.4 DVD I've tried it will show the boot screen with the Apple logo on it but no spinning status indicator underneath. It just freezes on that screen. Once it showed the status indicator but it just continued to spin for about 30 mins, at which point I gave up. Same issue if I try to boot the hardware test (except it freezes on the hardware test loading icon rather than the Apple icon). The superdrive appears to work as it is accessible in target disc mode.
I've reset the SMU and reset the PRAM via the keyboard shortcut. The one thing that leads me to think it's a firmware fault is that when I run the 'reset-nvram' command it gives an OK, but when I then run 'reset-all' it freezes rather than rebooting. Any ideas anyone?
Information:
Powermac G5 Dual 2GHz
I noticed that when I restarted my MacBook today, the Apple logo takes a while (20-30 seconds) to just show up before the spinning gear shows up.
Things I've tried
1. Repair disk permissions
2. Verify disk
3. Reset PRAM
4. Boot into Safe Mode
5. Make sure Mac OS X 10.6.5 is the startup disk
i'm trying to boot from the Snow Leopard install disc so I can format my drive and re-install, however... it just gets stuck on the white screen with the grey Apple logo, what's up with that?
View 5 Replies View RelatedI have Time Capsule and everything is backed up on there. My data is on a separate USB HD + Drobo, but for now I need my iMac to boot but it won't. It won't even get into the Desktop. all the guides online says double click the Install Icon this and that...I would if I can get into the Desktop !
It is just stuck on the Apple Logo screen with the spinny thing, that stops spinning!
Sometimes, when I turn on my iMac (10.6.2), the system will not load, you can see the grey screen but empty, no apple logo there. I have to force a shutdown pressing the power button and when I turn it on for the second time it will work properly.
It only happens once in a while but I cannot understand why, since nothing changes.
PS.- I have verified my disk with the disk utility and everything seems fine.
there back in September when I got my macbook I had the problem where it wouldn't boot past the apple logo screen and it was taken away and the hard drive had to be replaced and now it has happened again! I'm so annoyed as Im getting really close to exams at Uni so need my computer but will it need to have the hard drive replaced again!? As well with it being Lion I dont have a disk with it to try utility disk.
View 5 Replies View RelatedMy mother's unibody white MacBook will not get past the grey apple and spinning gear when you first boot up the computer. This was after she opened a link in an email from a friend who had her email compromised. Now I'm getting spam emails with the same link from my mother's hacked email, and her computer won't even get to the login screen. I took it to the genius bar only to be told it was likely HD failure, but the windows partition works without a hitch! What could this be? A trojan? Is there any way to retrieve data (really just pictures) before I attempt to reinstall OS X?
Info:
MacBook, Mac OS X (10.6.8)
I've checked disk permissions, run SMART check. the disk seems fine but the problem persists. It began a few days ago.
Info:
MacBook Pro (17-inch Early 2009), OS X Mountain Lion
My PowerBook G4 (Ti, 867MHz) just decided it didn't want to boot today...
The PowerBook has been asleep and not used for a few weeks. I woke it up last week for a few minutes to try and print out a document. It restarted just fine after installing the printer driver. Then it went back asleep until today.
I decided I had better shut it down as it has been sleeping a lot. It's shut down for about 5 minutes when I boot it back up to find it stuck at the Apple logo with the (spinning) spinner. What I tried to do to solve the problem:
1. Booted into Terminal mode (command-s) and typed exit so I could see the boot log. It appears to attempt to boot yet repeatedly prints:
> localhost /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[92]: Login Window Application Started -- Threaded auth
> localhost loginwindow[92]: _RegisterApplication(), FAILED TO establish the default connection to the WindowServer, _CGSDefaultConnection() is NULL.
[Code] ....
2. Booted into Terminal again, and mounted the volume. I was able to do ls to list the file contents - so I CAN get to my files. It's not a disk issue. Then I ran fsck -fy. It reported the disk as OK.
3. Rebooted and reset PRAM. No change
4. Reset NVRAM. No change.
5. Popped in the Leopard install disc and restarted. Booted into Leopard disc.
6. Tried to repair permissions from Leopard disc - it just hung and I had to cancel the process.
7. Verified disk from Leopard disc. Reported as OK.
8. Clicked the next button on the install screen. Tried to install. "You don't have enough space"... The skimpy 40GB HD is so packed with stuff that it can't install. And my external HD won't connect to it, it never shows up. Not like I can move off anything anyway as it won't boot...
I CANNOT format the HD. I have stuff on there I can't lose. Does the Terminal recognize and mount USB devices so I can copy from the Terminal? If not I guess I could delete some apps and Xcode and stuff, maybe the System folder...
