I currently have a Airport Extreme in my living room, I'm trying to boost up the signal in the rooms. Is there a way that I can use Airport Express as a repeater in the rooms via wireless and not via ethernet? I would like to use Express as a signal booster not to stream music
View 1 RepliesI made a deal with a neighbor where we share the cost of internet. We use a wifi network and I use my MBP in my office and get 2, sometimes 3 bars of wifi. I wanted to extend wifi to the rest of the house and also be able to plug in my printer so I bought an airport express.First problem I'm running into is that where my 2009 MBP 13" laptop gets 2-3 bars, the router doesn't even SEE the wifi signal from the original D-Link Router.
View 3 Replies View Relatedthat has a failed airport card, but ethernet port still works. Can I use an Airport Express to connect to it by a 3 foot ethernet cable and still have my Airport Extreme Base Station set its IP and subnet addresses by DHCP? I don't want the AE to set the addresses, only the AEBS to set them.
View 8 Replies View RelatedI want it to provide a boost to the signal in the basement for my touch. As well as stream music from my laptop. The issue Im having is that the music keeps on cutting out. The newer one this is listed under is working fine, but on the other side of the room, it is setup to Extend the 'n' network (which I assume means allow my laptop better signal in the basement.)
The older one is on a b/g network, which I setup as a WDS network and then setup the express as a WDS relay, which I assumed would provide signal strength for the b/g network in the house (so we are running b/g & n). But setting it up as a relay it still loses connection with the laptop (I am assuming this is with the b/g network itself) and I believe that the touch's WiFi connection also drops with the music, because it is all the b/g network.
The b/g network trickles into the basement, but I assumed with the b/g touch setup as a WDS Relay, that it would strengthen the signal for my touch and ALSO keep the signal strong between the laptop and the express (Im guessing they are talking over b/g). But after being setup as a WDS relay the music is still dropping, and I only assume the touch's wifi signal is dropping as well! I also had to setup the ENTIRE b/g network as WDS because I did not get an 'extend range signal'.
I have an Airport Extreme, with two USB hard drives connected to it. The Airport Extreme shares these disks to my wireless network via Airport Disks.
Upstairs I have an Airport Express, that wirelessly connects to my Airport Extreme downstairs, and extends the wireless network so I get a good wireless reception upstairs.
My problem is, that it does not seem like me Airport Express does a good job of forwarding my 2 USB Airport Disks to the extended wireless network upstairs.
For example, when I use the AirVideo iPhone app to stream video from my USB Airport Disks I get a server connection error when I go upstairs and the iPad/iPhone switches to the Airport Express networks. I cannot reconnect as long as it is on the Airport Express network. If I turn the airport Express off, and thus switch to the poor wireless reception from the Airport Extreme, I can connect to the USB Airport disks again.
The Airport Express is connected to the Airport Extreme in bridged mode.
Just a question for those who have used the Airports. Can a USB hub be used to expand the number of devices the Airport can use? i.e., an external hd, a laserjet, and an inkjet.
View 4 Replies View RelatedCan it? If it can, would Airtunes still work like normal.
In other words, can I be connected to my Airport EXTREME and Airtunes would still work since the Airport EXTREME and EXPRESS are using the same network wifi-name (the Express is just extending the Extreme's range).
I have an old Airport Express (A1088).I am running OSX 10.9.4 - I have downloaded Airport Utility 5.6 and yet cannot install - I am getting "This version of Mac OS X on this volume is not supported".Unfortunately no PC or old Mac available. I used to be able set up on IOS but cannot do that anymore either.Any clues how to re-setup this old airport that works ok.
Info:
MacBook Air (13-inch Mid 2012), OS X Mavericks (10.9.4)
i have top of the line Airport Extreme with the N enabled on my MacPro yet i get a Crappy Signal what gives? anyone else have this problem?
View 11 Replies View RelatedI'm all of the sudden having problems with the airport connection in my MacBook Pro laptop at home. In areas where it used to work---a week ago--the signal comes and goes from 4-5 bars to all of the sudden none and I am disconnected from my wireless internet. Nothing else has changed (cable modem, wireless router).
View 4 Replies View RelatedI just upgraded from 10.4 to 10.5 and my Airport meter is now reading 2 bars instead of 5. Same router, same position, different OSX only.
View 2 Replies View RelatedAfter configuring wireless security on my Airport Extreme base station, the Airport Express I use to stream iTunes music to my whole-house stereo system has disappeared. Airport Utility can't see it. Yes, I checked connections. All I get is a blinking yellow light on the Express. The base station works as its supposed to.
I have a 17" Powerbook G4 with a 1.33 GHz Power PC processor. I'm running MacOS 10.5.8
MBP 2.2; OSX 10.4.11; Airport Express 802.11n (version 7.3.2); WD MyBook 320GB (format Mac OS Extended) I'm trying to get the WD HDD setup as a wireless hard drive, but it's not showing up at all in Airport Utility (I don't even have a 'disk' tab in the 'manual setup' menu). Airport Disk Utility just says "no airport disks found." Of course the HDD works fine when plugged in directly to the MBP. I've searched apple support and these forums, but haven't found anything that works yet. All help I have found says use the 'disk tab' in AE manual setup window. What do I do without a 'disk' tab? (or how do I get one?) is this a firmware/software issue with the AE?
View 4 Replies View RelatedI currently have the apple extreme as my wireless router. It works great. I absolutely love it. I have two macbook pro's (wife and I both have one) and use it for my PS3 and Xbox 360. I started a new job and was given a free HP desktop (not my choice, but hey, it's free, so what can I say). The desktop is not wireless and I am not able to put my computer near the airport extreme because my TV already owns that territory. Today I bought the Airport express to use as a bridge (and other things in the future). I have plugged it in. I opened the airport utility using my macbook. It finds my extreme and my express. I select that I want to set up the express. I select that I want to set it up using an existing wireless network. I select my airport extreme. It tells me that it has to restart the express. I wait approximately 3 minutes. It then tells me that the settings to the express have been changed but it's not able to find it.
My main goal is to use the express as a bridge. I have the express plugged in beside the desktop and want to run an ethernet cable from the express to the desktop to allow for wireless capability.
AirPort Express doesn't show up in AirPort Utility 6.0. I haven't updated the AirPort utility on my laptop, and can find it there. 6.0 doesn't even has a scan button... I've done a hard reset of the AirPort Express, still isn't showing up.
View 2 Replies View RelatedI have my AE set up in my office where three computers and two printers are picking up its signal just fine. However, I have a computer in another room that is only about 30 ft away from the AE router and sometimes the signal is very week while other times it won't connect at all. Yet, I can pick up other networks from other houses just fine.
View 5 Replies View RelatedI have an ibook G4 1.42 ghz. It worked fine until recently. After connecting to a wireless network for a few minutes, it then begins to sporadically drop out. And after losing the connection, it can't detect any wireless networks. Turning off the card, restarting the computer, letting it sit for a few minutes... signals come in and out, but then drop again.
I'm using OS X.4, so this isn't a software problem, the OS, or caused by an update. The antenna also isn't faulty. The computer reads the card as being fully functional, but just doesn't detect any wireless networks. I've exhausted all software solutions and now can only conclude it's a hardware problem. Given the symptoms I've described, would the best idea be to replace the card altogether?
Sometimes while using my Powerbook in the house, the signal on my Airport connection will either drop completely or drop down to 1 bar which makes it extremely slow and barely usable. Normally, I'd blame the router, but the couple times this happened, I grabbed my brother's MacBook, set them side-by-side, and connected to the same access point, my PB had 1 bar or nothing at all, and his MB was at full strength and was working fine. Eventually, the PowerBook will go back up to full strength and be usable again, but after awhile, it will go back down too. It's an intermittent thing.
View 4 Replies View RelatedCan I add an Airport Extreme to a network to get a stronger signal? Im using my roommates wireless (WAP) signal with only one bar. I have the white Airport Extreme that looks a flying saucer. (802.11g?) to his Linksys wireless.
I am having random slowdowns on my connection speed using Airport (nothing to do with the notorious performance issues which I also suffer).
My appleTV and my HP 2140 get 90% (it's right by the router) and 80% (floating around the same floor of the house) signal strength respectively, download speed and throughput seems very stable on both, however on the iMac (that's about 10 feet away from the router) the signal strength is 28% ! this is incredibly low and even though it does not always hurt download speed it does hurt the total throughput when sharing files over the network. Also the SNR (signal to noise ratio) is incredibly low, below 30 all the time.
I recently moved into a new apartment that has an Airport Express connected to a cable modem. The network does not have a password. I want to put a password on it so that not everyone in the building can use our internet.
When I connect to the Airport via the Airport Utility, it recognizes the Airport, but asks for a password when I try to configure it. I tried doing a soft reset on the Airport, but it didn't change anything. Are there two passwords for an Airport? If so, how can I bypass the second one? The "Resetting Airport Express" page at [URL] doesn't answer this question. Do I need to do a hard reset? If so, is there anything I need to know about that? We no longer have any of the original literature that came with the product.
I am upgrading from a g wireless router to an n. I have a Belkin right now that I hate. Neither I, on a mac, nor my roommate, on a PC, can get a consistent connection on it. Needless to say it's going back and I want to get an express or an extreme. I had actually bought an Airport Extreme first and it was lightening fast, but I was told that the Express was just as fast, so I went to exchange. The guy at BestBuy told me the Belkin was cheaper and just as fast, so I bought it. I would really like this to be my last trip to the store for a router. Do I need to shell out for the Extreme or is the Express just as fast if all you need is an n router?
View 4 Replies View Relatedhere's the run down: today I moved into a new place with two roommates. They have a wifi internet connection set up (modem + dlink router). I have been given all of the info regarding log ins and passwords. My Airport is telling me I have perfect reception and that I have a very strong signal. Yet, there is no internet (when I open Safari it tells me I am not connected to the internet). I've had this problem before, but it is usually resolved by restarting the modem or the router, by restarting my computer, etc. And here's the kicker: I am using, right now as I type, someone else's wifi connection... yet I accessed it with the same password. It's a very basic password (12345). I thought maybe this was our unit's connection, but I actually unplugged the modem and continued to use the internet with this connection. The problem is that this connection is very slow and rather useless. I'm actually able to use 3-4 of these with the same password (12345). One of them is called 'dlink,' the name of our router. But our connection is supposedly under 'Nicks,' my roommate's name).
View 1 Replies View RelatedSo this is my network set up:
A) Cable Modem connected to ethernet cord to new Airport Extreme Base Station.
B) Three Airport Expresses located around my house set on extending the network.
The airport extreme station is in the master bedroom and the room I am in is approx. 15-25ft away (thru a wall of course). I ran iStumbler and am getting ~42% signal and 23% noise from the main airport extreme. I am getting about 49% from one airport express with ~15% noise, ~42%/17%, and ~45%/15% from the last. Sometimes they can drop as low as 35% signal... This is not prime. Now, I do get better signal during the day, so other networks could be interfering.
I have checked local networks and their respective channels, and moved mine to an all time random number of 3. The other networks are mainly on channels 6, 8, and 11. Before I moved my network to 3, it was on channel 11. I get the same signal/noise before and after the channel move. Finally, to finish off the description... This current computer is located on the third floor. The main airport extreme is located on the third floor as well, with a relay airport express right outside the door of the master bedroom. It relays to the other 2 airport expresses. (it is also a regular airport express). Currently, all Airports are set at a Multicast rate of 2mbps.
i am trying to get my airport extreme to receive a wireless signal and send it through a ethernet cable to my computer. how would i go about doing this?
View 2 Replies View RelatedI'm using an airport extreme (latest firmware) with 10.6.3 on a mac pro and a macbook pro. The mac pro is wired the macbook pro is connected via wireless.
I constantly have signal drops. While the airport extreme seems to stay online (green light is sold) the cable modem always resets itself.
I can't figure out if this is because of my Optonline service or due to my router (airport extreme). Cablevision states nothing is wrong with my cable internet connection and the issue may be with the router. I've tried three different modems from them and they've supposedly checked everything (wires, signal, etc). I still think it has something to do with them. I'm hesitant to try DSL as it is slower (no fios here yet).
I don't get how it can be the router if both my desktop and laptop lose connection to the internet at the same time if they happen to be connected online at the same time.
Is there anything I'm overlooking in regards to the airport extreme? Should I trash a particular preference or try a different setting?
I'm kind of desperate at this point since it is highly annoying to constantly get knocked offline more than 5 times a day.
my Mac Pro has a very weak wireless connectivity � 4-10% packet loss on average, so I want to try to upgrade it's Airport antennae (I've had the same issues on my PC before I bought Mac Pro, I fixed them by upgrading the antenna).
Does anyone have any experience with external antennae for the built-in Mac Pro Airport card?
What are the plugs in Airport called? (RP-SMA � is that right?)
Are there any converters to RP-TNC, so I could plug a normal external PC antenna? Will there be any problems?
There are times that my signal are fading. What do I need to boost up my signal? I had an Imac Intel core duo which i bought last year.
View 7 Replies View Relatedon my new second hand ibook the wireless is really poor, 50% of the time it cant even find it, im using a bt homehub which on the pc it can run at about 6mb/s but the mac runs below 1 although last night it strangly went up to 5 for a miniute or two, i have tried making sure the airport card is in properly and the connector i assume is the ariel?? seems to not plug in very well? a little loose ? do i need a new aiport card?
View 2 Replies View RelatedWith my MacBook Pro sitting on the desk right next to my Airport Extreme Base Station, I get, according to iStumbler, a varying signal strength between 50 and 75%. I see the same with my wife's MacBook. I also have an Airport Express in another room set to "Extend a network" and I see about the same there. Shouldn't the signal strength be higher?
