im new here and im a little unsure where to post about my macbook, But i hope this is the place. Anyways, i was wondering if its possible to toggle the fn button, cause im a flash animator, and its pretty anoying that i have to hold fn down to create a new keyframe.
View 6 RepliesMy 15" early 2008 MacBook Pro won't shut down unless I hold the power button. I have done extensive searches and have done the following and the problem still persists. I have pulled the battery to reset the SMC or whatever it is called. I ran disk utilities and repaired the permissions. I deleted unnecessary files in the preferences folder...... still no go..... in fact it won't load software updates because it gets hung up.... then I have to force quit it by holding the power button..... I am at a loss.
View 9 Replies View RelatedI just installed 2 4 gb of ram in my unibody mac book pro 13"
I now get a error saying to push and hold the power button and then restart. The message keeps coming back up every time any thoughts ?
My mac book pro (current gen) shuts off after closing the screen and won't start up unless I hold the power button for about 10 secs.
Info:
MacBook Pro, Mac OS X (10.7.4)
I have just shipped my Mac Mini to its new home and I've had reports that the panic error is appearing on boot up: "You need to restart your computer. Hold down the power button for several seconds or press the Restart Button." This screen appears on the blue window just after the grey apple screen has disappeared and does not get as far as the desktop at the same point each time. We have tried to reinstall mac OS from the original install disk but holding the "C" Key or the "Option" Key down on restart doesn't boot from disc. Is there a way you can view the Kernel Panic log before you boot into Mac OS so we can try and pin point the source of this problem. I'm wondering if this could have been the result of the shipping that has caused some hardware to come loose.
View 3 Replies View RelatedSo i pull the plug and wait 30 seconds and the light is still on when i put the plug back in. when i hold the force quit button. Nothing happens. the light just stays on.
View 4 Replies View RelatedMy iMac won't shutdown unless I hold down the power button. It just sits on the grey screen, sometimes with the cursor sometimes not.
Info:OS Lion, Mac OS X (10.7.2)
Sometime when I stop using my MBP for a minute or so, the screen goes black and won't wake up. I can see that the lights are on the keyboard and it's running but won't wake up. I will have to hold the power button down and then restart. Does any one know how to fix this? It's starting to do it more and more ofter.
View 1 Replies View RelatedSo I'm having issues with the computer not waking up in the morning. I guess it goes into a deep sleep of some sort and I have to hold the power button twice to turn it on, and get greeted with a computer experienced a problem message on login.
The most recent log in the system diagnostics is titled:
aosnotifyd,diskarbitrationd_2014-08-21-184310_MacBook-Pro.shutdownStall
And the brief details are:
ate/Time: 2014-08-20 22:02:42 -0700
OS Version: 10.9.4 (Build 13E28)
Architecture: x86_64
Report Version: 18
Command: No Target
[code]....
Info:
MacBook Pro (Retina, 15-inch, Mid 2014), OS X Mavericks (10.9.4)
Got a tricky one here: powerbook G4, 1.25ghz, 1GB RAM (2x512), 80gb HD, APX, 15" LCD, serviceable battery, SuperDrive, OS: 10.4.11. It was brought to me with a boot problem: Computer turns on, gives the start up sound, backlight comes on, apple logo shows, spinner spins... then you get the dimmed screen, large option icon and "You must hold the power button and restart your computer": a kernel panic. I've seen this a few times before and the last time, I fixed it with a new hard drive and the removal of RAM from a bad ram slot.
What I did was:
1) Replaced existing 80GB HD with a backup 30GB drive. Then booted with a Tiger CD (the computer won't start with my disk warrior cd, nor with a tiger DVD). I was able to install Tiger and restart the computer. But the airport card doesn't show up. I tried a known good airport extreme card and this too has not shown up.
2) I hooked up the 80GB drive to my PC via MacDisk and checked it. Sure 'nuf it had loads of problems. MacDisk went through and fixed it (I'm not sure what the problems were as I'm new to MacDisk and don't know what it's looking for and fixing when it does).
3) With the computer running the 30GB known good HD, I started having the same kernel panics so I removed the first RAM chip (512MB) and tried to reset the PRAM.... here's where it went wonky. (I know, only change one thing at a time...)
4) As I said I tried to reset the PRAM (Option, Command, P, R, at start up). While I can get the computer to not boot, it won't restart. I don't know if this is just unique to this machine. Next I tried to reset the NVRAM and again got nothing. The screen wouldn't come on at all. After about three or four resets, the computer did start in Open Firmware mode. I reset the NVRAM from there and restarted (reset-nvram, reset-all). Still nothing on restart.
5) After trying to start it 15 times like this, I swapped the bottom RAM card to the top slot and removed the airport card (again, I'm stupidly trying to change two things at a time). BAM, computer boots... I put back in the 80GB drive that's been "fixed" by MacDrive and BAM, that boots fine too.
So then I put back in the airport card and it will boot, but won't recognize the airport card. I've re-seated it about a dozen times and have used terminal cleaner on the card and on the socket for the ribbon cable from the card slot to the logic board. As it sits, I can't get the airport card (either of the two) to show up at all. I did realize that the open firmware did reference a problem, but I forget the code now and when I looked it up, the references were to a failure of the airport card, but there were also more general references, so I can't be sure.
I'm thinking now that it's the airport card controller on the logic board, the bottom RAM slot and a corruption of the hard drive. Yes, there was a history of moisture into the device and I think a drop in it's past too. I'm the Mac repair technician for the people at the local bike shop, so I get to trade my repair work for their bike repair work. The problem is that they ride their laptops like their bikes, hard and greasy. I'm really wondering about ways to get the airport card back up and running. Or, baring that, a good card-based wireless adapter that I can slide in.
My Macbook pro is not booting properly. When I start it up, it goes through the normal process and gets to a point where a screen comes up telling me: "You need to restart your computer. Hold down the Power button for several seconds or press restart now" This happens every time. I tried to start in safe mode and holding down the option key and selecting the mac partition. Neither would work.
View 3 Replies View RelatedWhenever I open my mac mini it comes up with the same message "You need to restart your computer hold down the power button or press restart" in four different languages.
View 2 Replies View RelatedWhen I go to a friend's blog and click on "Print," the "Create a New Tab Button" at the top of Safari goes gray and unusable. Usually, I have to Quit Safari and restart it, but today, after printing, the button returned to normal spontaneously
Info:Mac OS X (10.6.8)
I cannot click the + button..
View 3 Replies View RelatedI have a major problem with FCP 10. I cannot for the life of me figure out how to do a simple audio level adjustment using the keyframe editor. I have a audio-video clip that is using dual channel mono audio. I have a shotgun mic on one channel and a handheld mic on the other.
I've gotten as far as getting both incoming channels to playback on both outgoing channels. What I need to do is to shut off one channel or the other, periodically, in order to preserve the quality of the audio. FCP won't let me use keyframes and the range editor wasn't work either. It should be simple but it seems that it isn't. What do I have to do to cause FCP to do this very simple operation?
I have a Macbook Pro running 10.9 Mavericks Operating System. An Apple support person created a new partition on my HD to troubleshoot a problem I am having and now I am waiting for him to call me back but he never told me how I toggle back and forth from this new partition to my regular HD.
I cannot access my regular HD!
My Dell u2711 is my primary display. Sometimes I wake up the macbook out of sleep mode and forget to have the lid shut. Consequently the Macbook screen comes on as well. Everything is working as it should but I am curious is there a quick way to switch the Macbook display on and off with the setup I have described?
View 11 Replies View RelatedI am moving to an IMac after years of being a windows user. Both my wife and I have our own iTunes user name, library etc. In windows you can hold the shift key when clicking other iTunes icon and you can choose which library you want. How do I do this on the mac?
Info:
iMac
I want to use an iMac for one company and run company two off my Mac Book Pro but use the 27 inch display and toggle back and forth, can I do that?
Info:
iMac, Mac OS X (10.7.3)
If I have two windows of Safari open at the same time, how do I toggle between the two?
View 18 Replies View Relatedfor a Windows machine can I toggle back to the Mac desktop or is the system required to be off? I was never sure of how that worked
View 2 Replies View RelatedI have been googling around but I can't find anything sufficient. I would like a simple way to enable a keyboard shortcut to toggle bluetooth on and off; one feature I enjoy having turned on is the option under Universal Access to disable the trackpad if an external mouse is connected. This is great when I'm at my desk, but if I move my MacBook Pro to another room it doesn't necessarily disconnect the bluetooth mouse and thus I have to go back to my desk to shut the mouse off in order to get my trackpad back again.
So a quick simple tool, like maybe fn+B or cmd+B or whatever, would be awesome.
I tried recording an Automator macro but it can't discern whether bluetooth is on already or not, plus there was a huge lag time of five seconds each time I triggered it (on top of it stealing window focus).
I need to be able to toggle my primary display between two monitors connected to my Mac Mini. I know that this is normally done by the following:Display Preference Pane -> Arrangement -> Drag the menu bar to the monitor your want as primary I'm looking for a hotkey or keyboard shortcut to toggle this more quickly. My graphics apps have to bind to the primary, but I also need to send full-screen output to the primary display, thus blocking the menu bar and dock.
View 2 Replies View RelatedAs soon as I unplug the mac from the wall - it dies. its not even 30 days old. I presume this is a defective battery? there are no lights on the side at all
Info:
Mac Pro, Mac OS X (10.7.3), MAC PRO NEEDS AN UPGRADE!! More PCI
my macbook no longer holds a charge after having it plugged in all night.
Info:
MacBook
i have a macbook pro mid 2010 and i was wondering what the max storage was. i am hoping to put in 3 terrabites and was wondering if that would be compadable.
Info:
MacBook Pro, Mac OS X (10.7.4)
I just recently got a Macbook Pro 15" and is wondering how much ram it can hold. It's mid-summer, currently holding 2gb in its 2 memory slots totalling 4gb of ram. It's the $1799 version. I've been trying to find out in the internet but they're all from the older versions.
More Info=Processor 2.3 GHz Intel Core i7Memory 4 GB 1600 MHz DDR3Graphics Intel HD Graphics 4000 384 MBGraphics NVIDIA GeForce GT 650M 512 MBI just want to know how much it can hold so I can plan on upgrading later on.
Info:
MacBook Pro, Mac OS X (10.7.4)
Wondering why i cant toggle app windows after i reinstalled osx10.5 with cmd-<?
i use this command all the time and know it wont work, any one smart who knows the answer to this issue?
Can I toggle between Air Print and an Epson printer driver? The only way I can print directly on CDs with my Epson XP-810 is to use Epson's driver. Normally, I'd prefer to use Air Print.I'm running OSX 10.9.4.
Info:
2.8 GHz Intel Core 2 Duo iMac, 4 GB SDRAM, 931.19 GB drive
My Macbook Pro won't hold a wireless signal. I don't have another wireless signal to test, but have tested other devises which connect fine.
'07 model MBP core duo running OS4.11 + original Airport (hey it still works). The MBP will only stay connected now if my base station within 10' or so. It might connect 30' away, but looses the signal after loading a few pages online. It seems like its getting worse -- maybe not, but seems like it is. I can connect just find with my other MBP, iPod (streaming audio across the house, etc) and PS3.
