I have two 1.5TB HDs, RAID 0, as my itunes library. I use Time Machine to back up all my drive, but I also wanted to clone the RAID but only use a single drive as the clone. Will this cause any potential problems since its going from a 2 drive RAID to a single drive.
View 6 Replies
I have a Lacie ext hard drive with 2 x 250gb HD that were one RAIDed into a single 500gb HD. I ran this update Lacie firmware update: http://www.lacie.com/support/drivers...r.htm?id=10053 And now my HD will only show up as two separate HDs of 250gb instead of a single RAID HD of 500gb.
View 6 Replies View RelatedI just order a MBP 15" i7 that i will be using for mostly Photoshop work.I was wondering if anyone had any experience with single ssd vs two at 0 raid in regards to photoshop work and or similar apps? If there is very minor speed gains for 0 raid
View 4 Replies View RelatedI have a RAID 0 set up with two 1.5TB HDs. I am doing some reorganizing and want to take all the data on the RAID 0 and move it to one of the hard drives in the RAID 0 and create to single drives. Is there any way of moving all the data from a RAID 0 onto one of the HDs?
View 4 Replies View RelatedIs it possible to mirror a RAID-0 array to a single drive?
For example, I will be setting up 3x1TB on a RAID-0 (striped) array and i want to mirror it to one 1TB drive. Is that possible or do i have to resort to Time Machine ... ugh
and YES i've already STFA! no answers as of the start of this thread
[URL]
-edit i assuming Time Machine backs up the "volumes" and not the "drives"
I've done a byte to byte clone of my original 320GB bootcamp drive to a 750GB drive (connected via USB). So I remove the 320GB from bay 4 (MacPro) and slot in the 750GB into bay 4. I fire up my MacPro hit the Option key during power up and all I get is an option to select my Mac drive not my new 750GB Windows drive.
So I boot into OSX (since I have no other option) and I can see my "Untitled" Windows drive on my desktop. I can select it and browse it and I see all my Windows files. Also, under System Preferences - Startup Disk, I can see my "Windows on Untitled" listed.
I'll be going with the OWC SSD(s) ExtremePro for the boot drive................ either a 2x60 OSX SW RAID 0 or single 120. I'd rather err on the side of safety but always looking for more umph If going RAID 0 would it be advised to go with a dedicated controller?My data drive will be 2x1T RAID 0.
View 22 Replies View RelatedCompatible to PCI-e 2.0
Boot to Mac OS X with Mac Pro (2006-2008) Models
Boot to Single Drive or RAID Array
Well,finaly it's bootable and raid bootable.Does anybody know is ti bootcampable?I just come back from windows,I find I lost so much,I can't even use foobar2000 and my 9800gt.
I hope it will be a positive answer
My current setup consists of my boot drive (250GB), a striped RAID (500GB) for storage and a 1TB Time Machine Drive.I have recently bought a new 1TB internal drive and would like to replace the striped raid with this drive, thus freeing up two 250GB drives - 1 which i will keep internally and the other will go into a external enclosure My question is can i just copy the files from the RAID to the new internal or do i have to use software to clone it?
View 2 Replies View Relatedi have Snow Leopard running in a RAID, and just a separate single drive installed for windows 7. Problem is, when i try to go to bootcamp assistant, it tells me that RAIDS aren't supported in bootcamp. I don't want to install it on my raid, just on the other single drive. Does anyone know a workaround or how to do this?
View 24 Replies View RelatedI'm still working out the details on purchasing a new MacPro. My Apple sales rep tells me that I can greatly increase the launch speed of applications and the system OS by purchasing 2 hard drives and using Disk Utility to stripe them together into a "software RAID". They claim it will be faster and more reliable than a single SSD. I know I've asked this question before, but the answers were over my head. I don't know anything about SATA raid cards, or SSD's except for their benefits. But I'm pretty sure I can stripe two drives together and make a software RAID.
View 24 Replies View RelatedI'm having a hard time deciding what to do with my two open HDD bays in my Mac Pro.I know I want to add more storage, but I'm not sure if I should use Raid0 or not.I store most of my media on a server but wanted to store the following in my MacPro and would need more hdd space.Bootcamp - obviously can't store in serverScratch drive - would write handbrake encodes to this then transfer to serverIn all I'll need around 1.5tbI already have a 1.5tb drive and would only consider buying another to put them into raid0. Should I bother with raid0 for the increased speed or just use the 7200RPM 1.5tb drive I already have?
View 11 Replies View RelatedI purchased a 128gb Patriot Torqx to run as the boot drive for my Mac Pro. I know that the new Intels are coming but I am happy with the Patriots and wanted some instant gratification. The machine is definetly snappier but doesn't quite have the pep as my MBP running a 256gb SSD as the sole HDD.
I have (3) 1 TB 5400 rpm drives in a striped RAID array. It seems sometimes when I start an application that lives on the SSD boot drive, the other drives begin to run as well (I can hear them spinning). Any thoughts on what could be done to speed up my system and also make sure that the SSD runs as independent from the traditional Hdd's as possible?I am running a early 2008 Intel 2.8ghz machine, 8 cores, 6gb RAM.
I want to clone my old pc's hard drive so I can boot it up on my iMac via Boot Camp and it will be identical to my PC - is this possible?How would I go about creating a disk image of my PC hard drive and then loading it up in bootcamp?Bootcamp will provide all the drivers I need but what about the old drivers installed for the PC hardware?
View 6 Replies View RelatedDifficulty deciding between 1 or 2. Unsure about real world performance gain of 2. No experience with SSDs or RAID 0. Worried about alignment and sleep/hibernate issues. Stock 5400rpm 320GB will go inside eSATA enclosure. Does anybody have a good eSATA ExpressCard/34 to recommend? I don't care about the SuperDrive. But I'll keep it for Care warranty purposes.
View 1 Replies View RelatedI have a Mac Mini that I plan to use as a simple file server with a 2TB external disk. I would like to be able to add future external disks to grow the original 2TB volume I create to 4TB, 6TB, etc. using RAID.
I know it is possible to add disks to a concatenated RAID set without destroying the data on the disks already in the set, but I cannot get Disk Utility to let me create a single-disk concatenated RAID set.
I have a PowerMac G5 and need to purchase an internal RAID card to create a RAID 1 mirror of the system drive... one that will allow me create a Hardware RAID 1 mirror, not software RAID through OS X.
View 2 Replies View Related"My name is Shaun, and I am a mac-aholic"
I inserted 4 new 3TB disks into the bays of my Mac Pro (2012), and there is no RAID option for them.
How I got here:
Inserted the WD Red drives, and they were not initiated.
I "erased" the drives, gave them names, and they appear in Disk Utility in grey drives.
Went to set up the RAID, and move the drives into the RAID, but got an error that they could not be used.
It appears to me that disk utility is not allowing me to fully use those drives. I Have created RAID drives before with no issue in RAID1 with 3TB drives before on this machine. Am perplexed, I thought this to be the easy and simple part of my upgrade odyssey! Did I screw up the initialization? On all FOUR drives?
Now, if I click on the drives, the RAID option does not present itself.
FWIW, I am using OS X 10.9.5, on Mac Pro 5,1. I boot from PCIe card. My end goal is to create a 4-disk RAID 10 using the four SATA connections on the MP.
However, I have just tried iDefrag. It claims it can justify defragmenting HFS hard drives, as long as it not done too often.
I have just tried it and the difference in performance is quite noticeable (as good as the alternative described above).
However, I wonder whether defraging a HFS drive is wise? Are there any potential pitfalls?
I've had a Roland XP-30 and just got the M-Audio MidiSport Uno and downloaded the latest drivers from the site. The device is recognized on my Powerbook, but I can't get any audio playback from the keyboard. I've tried messing with settings on the keyboard, but still can't get it to play or record on my Powerbook. In GarageBand, Reason, and Audio MIDI Setup the device is properly recognized.
View 5 Replies View RelatedI am useless with computers and i am trying to connect my macbook to my LG tv via hdmi.i have connected the headphone jack to the audio on my tv but i don't get any sound also how do i get my macbook to not go into sleep after 10 mins?
View 4 Replies View RelatedI found out what the problem is but i'm not sure which cable to get.My TV manual says 'Connect a D-Sub cable between PC IN [PC] connector on the TV and the PC output connector on your computer" (did that part <<) and then "Connect a PC Audio Cable between the PC IN [Audio} jack on the TV and the Audio Out jack of the sound card on your computer. . The port is next to the VGA cable in the pic.
View 8 Replies View RelatedJust got from Best Buy where they told me that my 17month computer (logicboard) has to be replace. I;m trying to access my files other than the one shares thru my XP computer but with no luck.
View 3 Replies View RelatedOver the past few weeks I have been having issues with Time Machine. I have a 2Tb drive for time machine. One of the partitions that it backs up is a raid disk with 2 disks in the concat raid disk. One is a 1Tb Firewire device and the other is a 750Gb USB devcie. What happens is that the backup starts and sometimes works but a lot of times the partition umounts itself and you get an error onscreen pointing out that you have disconnected the drive without unmounting it. A couple of seconds later the drive remounts and all is good again with the drive but the backup has failed. I have rebuilt the backup device and fsck'd the partition in question and I see no errors.
View 2 Replies View RelatedWhen I travel I would generally take a small travel drive that is clone of my white MacBook as a rescue drive.Now that I have the MBA I am wondering if I could just clone my 11.6 MBA to a 64 GB flash drive and then if the worst happened I could reverse clone from the flash drive to the MBA.
View 8 Replies View RelatedI just cloned my hard drive to a new and bigger drive. I did the OSX 10.5.8 update on the old western digital drive as a safety precaution, so that if it screwed up I would still have a good copy on my new Seagate barracuda. The update looks to have gone well and I will be waiting for a couple of trial days before backing the drive up again. My question is, when I clone the drive again(to the new seagate) how will that work? Should I erase the existing disk image(10.5.7) on that drive or will it overwrite the existing image with the new 10.5.8 one? This is the first time I have used carbon copy and don't really know all the in's and out's of it.
View 1 Replies View RelatedI have a Macbook running on snow leopard and I wanna upgrade my internal hard drive as it is currently too small. I downloaded Carbon Copy Cloner and cloned my entire hard drive to an EXTERNAL HARD DRIVE. Now, I have that new internal hard drive from wester digital. What do I do with it? replace the current internal hard drive with the new harddrive and then how do I get the data from the external hard drive with my cloned data to the fresh western digital? Do I boot first from external hard drive etc? I am not sure what to do now?when I was given the option which hard drive to clone (or which part of the hard drive to clone) there was also the option to clone "Install Disk". I don't need to clone that, right?
View 3 Replies View RelatedI had some problems with my 17" MacBook Pro and needed a replacement immediately. The Apple Store didn't have a 17" that met my requirements so I bought a 13" that I plan to give to my wife to replace her 13" non-pro.
So. I'm ordering a 17" over the Internet. When it arrives, I'd love to avoid ALL the configuration that I just went through to get this new 13" setup like my old 17". Is there any way to completely clone the drive in my 13" MBP completely and transfer the data to the new 17" MBP when it arrives?
i hear its possible to make a install emergency disk using a flash drive, i purchased a HP USB 16GB flashdrive v 165w, [URL]
i formated the drive as a Guid Partition, ignored preferences and all the stuff i could find online to see to it that i did it right but no go,
can anyone tell me if this drive is incompatible or which one i should exchange it for?
i tried cloning my original OSX Leopard DVD and i get errors when from both CCC and Super Duper,
I'm planning to replace my boot hard drive with a pair of RAID0ed SSDs. In order to familiarize myself with certain techniques I have build a software RAID0 from two 160 GB Maxtor SATA I hard disks. That went pretty much without problems. The two HDs are now sitting in position 1 and 2 in my Mac Pro.
The problem arises when I try to clone my boot drive onto the new RAID 0 drive. I was using disk utility and got an error message. Then I thought my fault was using disk utility from the HD which I wanted to clone and booted from the Leopard install disk. I then used disdk utility from that source to clone the HD boot drive to the RAID. Again I got the error.
What is going wrong? Do I have to approach this completely different?
