I just order a MBP 15" i7 that i will be using for mostly Photoshop work.I was wondering if anyone had any experience with single ssd vs two at 0 raid in regards to photoshop work and or similar apps? If there is very minor speed gains for 0 raid
View 4 Replies
I have two 1.5TB HDs, RAID 0, as my itunes library. I use Time Machine to back up all my drive, but I also wanted to clone the RAID but only use a single drive as the clone. Will this cause any potential problems since its going from a 2 drive RAID to a single drive.
View 6 Replies View RelatedI have a Lacie ext hard drive with 2 x 250gb HD that were one RAIDed into a single 500gb HD. I ran this update Lacie firmware update: http://www.lacie.com/support/drivers...r.htm?id=10053 And now my HD will only show up as two separate HDs of 250gb instead of a single RAID HD of 500gb.
View 6 Replies View RelatedI have a RAID 0 set up with two 1.5TB HDs. I am doing some reorganizing and want to take all the data on the RAID 0 and move it to one of the hard drives in the RAID 0 and create to single drives. Is there any way of moving all the data from a RAID 0 onto one of the HDs?
View 4 Replies View RelatedDifficulty deciding between 1 or 2. Unsure about real world performance gain of 2. No experience with SSDs or RAID 0. Worried about alignment and sleep/hibernate issues. Stock 5400rpm 320GB will go inside eSATA enclosure. Does anybody have a good eSATA ExpressCard/34 to recommend? I don't care about the SuperDrive. But I'll keep it for Care warranty purposes.
View 1 Replies View RelatedIs it possible to mirror a RAID-0 array to a single drive?
For example, I will be setting up 3x1TB on a RAID-0 (striped) array and i want to mirror it to one 1TB drive. Is that possible or do i have to resort to Time Machine ... ugh
and YES i've already STFA! no answers as of the start of this thread
[URL]
-edit i assuming Time Machine backs up the "volumes" and not the "drives"
I'll be going with the OWC SSD(s) ExtremePro for the boot drive................ either a 2x60 OSX SW RAID 0 or single 120. I'd rather err on the side of safety but always looking for more umph If going RAID 0 would it be advised to go with a dedicated controller?My data drive will be 2x1T RAID 0.
View 22 Replies View RelatedCompatible to PCI-e 2.0
Boot to Mac OS X with Mac Pro (2006-2008) Models
Boot to Single Drive or RAID Array
Well,finaly it's bootable and raid bootable.Does anybody know is ti bootcampable?I just come back from windows,I find I lost so much,I can't even use foobar2000 and my 9800gt.
I hope it will be a positive answer
i have Snow Leopard running in a RAID, and just a separate single drive installed for windows 7. Problem is, when i try to go to bootcamp assistant, it tells me that RAIDS aren't supported in bootcamp. I don't want to install it on my raid, just on the other single drive. Does anyone know a workaround or how to do this?
View 24 Replies View RelatedI have a Mac Mini that I plan to use as a simple file server with a 2TB external disk. I would like to be able to add future external disks to grow the original 2TB volume I create to 4TB, 6TB, etc. using RAID.
I know it is possible to add disks to a concatenated RAID set without destroying the data on the disks already in the set, but I cannot get Disk Utility to let me create a single-disk concatenated RAID set.
I'm having a hard time deciding what to do with my two open HDD bays in my Mac Pro.I know I want to add more storage, but I'm not sure if I should use Raid0 or not.I store most of my media on a server but wanted to store the following in my MacPro and would need more hdd space.Bootcamp - obviously can't store in serverScratch drive - would write handbrake encodes to this then transfer to serverIn all I'll need around 1.5tbI already have a 1.5tb drive and would only consider buying another to put them into raid0. Should I bother with raid0 for the increased speed or just use the 7200RPM 1.5tb drive I already have?
View 11 Replies View Related"My name is Shaun, and I am a mac-aholic"
I inserted 4 new 3TB disks into the bays of my Mac Pro (2012), and there is no RAID option for them.
How I got here:
Inserted the WD Red drives, and they were not initiated.
I "erased" the drives, gave them names, and they appear in Disk Utility in grey drives.
Went to set up the RAID, and move the drives into the RAID, but got an error that they could not be used.
It appears to me that disk utility is not allowing me to fully use those drives. I Have created RAID drives before with no issue in RAID1 with 3TB drives before on this machine. Am perplexed, I thought this to be the easy and simple part of my upgrade odyssey! Did I screw up the initialization? On all FOUR drives?
Now, if I click on the drives, the RAID option does not present itself.
FWIW, I am using OS X 10.9.5, on Mac Pro 5,1. I boot from PCIe card. My end goal is to create a 4-disk RAID 10 using the four SATA connections on the MP.
I purchased a 128gb Patriot Torqx to run as the boot drive for my Mac Pro. I know that the new Intels are coming but I am happy with the Patriots and wanted some instant gratification. The machine is definetly snappier but doesn't quite have the pep as my MBP running a 256gb SSD as the sole HDD.
I have (3) 1 TB 5400 rpm drives in a striped RAID array. It seems sometimes when I start an application that lives on the SSD boot drive, the other drives begin to run as well (I can hear them spinning). Any thoughts on what could be done to speed up my system and also make sure that the SSD runs as independent from the traditional Hdd's as possible?I am running a early 2008 Intel 2.8ghz machine, 8 cores, 6gb RAM.
My current setup consists of my boot drive (250GB), a striped RAID (500GB) for storage and a 1TB Time Machine Drive.I have recently bought a new 1TB internal drive and would like to replace the striped raid with this drive, thus freeing up two 250GB drives - 1 which i will keep internally and the other will go into a external enclosure My question is can i just copy the files from the RAID to the new internal or do i have to use software to clone it?
View 2 Replies View RelatedI'm still working out the details on purchasing a new MacPro. My Apple sales rep tells me that I can greatly increase the launch speed of applications and the system OS by purchasing 2 hard drives and using Disk Utility to stripe them together into a "software RAID". They claim it will be faster and more reliable than a single SSD. I know I've asked this question before, but the answers were over my head. I don't know anything about SATA raid cards, or SSD's except for their benefits. But I'm pretty sure I can stripe two drives together and make a software RAID.
View 24 Replies View RelatedI have a PowerMac G5 and need to purchase an internal RAID card to create a RAID 1 mirror of the system drive... one that will allow me create a Hardware RAID 1 mirror, not software RAID through OS X.
View 2 Replies View RelatedI just bought a Guardian Maximus RAID1 kit and I have two 1TB drives in it. I'm using it over Airport Extreme as an airdisk (mac osx 10.6.2)
My question is simply: am I running a risk by partitioning it into two partitions? Should I ever have to rebuild the failed disk (which I understand is really simple with the Guardian Maximus) - will it have trouble doing two partitions? I'm using one 500gb partition for time machine and one 500gb partition as redundant itunes/media.
I have a macpro with 4 x 1tb drives
Is it possible to get a highpoint raid controller and put those 4 drives in a raid 5 array (and then create partitions inside that array) - or do you need to have 1 drive by itself for the operating system, and then create a raid array using the remaining 3 drives?
Lastly, are the highpoint 3500 series a decent card? and fully compatible?
I have a new Mac Pro Quad 2.93 with the Mac RAID card installed with four 1TB drives setup in a RAID 5 array. When creating the volumes in the RAID utility, you can not edit them, resize, etc. If one large volume is created in the RAID utility, you can then partition that one volume using the Apple Disk Utility, which then allows you to resize if needed.
View 1 Replies View RelatedI'm using the software RAID right now. Everything is set as RAID 10. I want to move to a RAID card� if I keep it as RAID 10 will I still need to redo everything?
View 1 Replies View Relatedive put 4 of the hitachi 1tbs in my new mac pro.. and i really want to do Raid on them eventually.. and buy the pricey apple raid card.. i'll do it.. but speed wise:
How fast is a Sata connection straight from HD>Motherboard... ~75mb/s?
Is the Raid 5 config with all those drives much faster... around ~110mb/s?
Do you know if there is anyway to get a 5th drive into the raid 5 array? using the ODD space.. or some externals too... i need as much as space as possible...
And boot camp wont work with raid card anymore? I was thinking to have the startup disc be a raptor to increase speed on the apps, how would it integrate with the raid card, etc
I am planning on getting a 2010 MP when they come and have a question about it. I am 90% sure that with my budget, I will not be able to after a RAID card. I am wondering if software RAID would be alright or if it's so bad it's not worth doing. Also, there is small chance that I could buy a RAID card later on, how would I install it? I will be using it for 3D animation with Maya and some zbrush modeling. Also I will be doing some Photoshop and illustrator and maybe some gaming on win 7 boot camp. Feel free to list any other pros and cons about either a software RAID or hardware RAID, I wana make sure I have all the details before making a final decision on it.
View 24 Replies View RelatedI have never setup RAID before and this question may be totally stupid for that matter.
Can I setup RAID 1 (or call it mirroring) without the RAID card? I have two 1TB internal drives in my Mac Pro and I want to mirror them. I don't want to spend another 700 bucks just to setup a mirror.
Disk Utility shows some RAID options, but I am not sure how to use them, or if they will work at all without the RAID card.
On my 2009 Mac Pro, OS X's disk utility seems to allow the provision of making a mirror RAID or a stripe RAID.
Is it possible to shove in 2 drives, make a RAID 0 for two of them, and then add in 2 more drives to make a RAID 1 out of that RAID 0? (a RAID 0+1?)
I have seen a few videos about mastering and gave it a try myself. It can be done by clicking the master tab, then going to the Input 1-2 column setting and then clicking setting - mastering, etc.When I first did this a few weeks ago, there were many options such as hip hop mastering, electronic mastering, etc.Now, when I do so, I have different - much less enticing options and have no idea where the good ones went.
I am transitioning systems from a G5 tower to a Mac Pro. In the mean time I am using my Late 2011 Macbook Pro as my primary machine. I have have a Sans Digial 5 bay RAID 5 unit that was connected to my G5 via eSATA that I would like to connect to the MacBook via USB. I am able to connect the RAID to my MacBook Pro and the volume does mount - though I did need to unlock the permissions in order to write new data. At one point I ran across a comment that Mac laptops do not support port multiplication and that RAID arrays could be corrupted through use with a MacBook.
View 1 Replies View RelatedHow can i make a single partition on mac book pro? My bootcamp is not working properly,so i need to return back to a single partition .
Info:
MacBook Pro, Mac OS X (10.6.8)
I am thinking about buying a HD for a full system backup and all files. I am worried about getting such a big HD and having it fail, thus loosing years of data. Is there any redundancy in a 1TB drive does partitioning help? What if the entire drive fails or are there multiple drives in those external hd? I need a reliable backup system for music, photos of child, that will last years. I want to be able to use the HD with both formats, pc and mac...what should I format with or is that a good idea?
View 2 Replies View RelatedMy MBP is 5,1, at last few months I use 2 HDD in raid 0, it fine and smooth, but after I upgrade 2*SSD ( OCZSSD2-2VTXE60G ) the nightmare is coming, only see one SSD (in org hdd bay), the optical bay never see, at first time I thought may be SSD is dead, so try to replace them, both SSD is work, second thought is optical bay dead, so put the hdd back, it work.
I don't what's going wrong, I just thought optical is not fit OCZ, may I know who is using OCZ in raid 0 please kindly tell me which optical you using.
can use G-Raid Mini SSD 256GB
View 7 Replies View Related
