Intel Mac :: Audio Interface Just Stops Showing Up
May 23, 2012
I've own an apogee duet for that last year, and have had zero problems. I just got the ensemble the other day for recording drums. I followed the install instruction carefully, updated all software, and firmware. And the interface wont show up in my system preferrences (the ensemble and the duet).
I swapped the firewire cables and still nothing shows up. I plugged the ensemble into my friends lab top, and it see's it right away.
So I thought maybe my firewire port isn't working...But when I go to the apple menu, and then "About this Mac" and hit "more info", "system report" under the Hardware tab at firewire... it says the ensemble is plugged in?
I just got a 21.5 in. iMac and it's not recognizing my firewire audio interface. I have a 400 to 800 cable from the interface to the iMac and it's simply not picking it up.
I work NOC Support / Operations for a decent sized provider in the midwest-ish area. I configure radios, routers, switches, etc CONSTANTLY. I need an ethernet interface. So I have the ThunderBolt Gig Ethernet adapters.
I plug one in every day, running DHCP, no issues. Then I roll it over to a private IP to setup a radio. At this point, the interface is dropping (because I am rebooting the radio over and over), and I have to change the IP on it consistently. After making four to six changes, the interface just stops responding. In the network prefs, its red, as if it doesn't have a good working connection. I open the network anaylizer, and it shows me that the interface is up, with no IP.
I've disabled the interface by turning it off, nothing. I have unplugged the adapter and the cable, network anaylizer still shows the port up and negotiated at 100/1000, but theres nothing there...
When I'm at home, I usually use an E-MU 0404 USB audio interface to channel sounds from my MBP. The problem is that every time I turn on the interface, the sound is distorted and corrupt. It is not a problem with the hardware; my monitors and interface work properly. The only workaround is to restart the computer with the interface connected and on, which clears up the sound. However, this is very inconvenient to do every time and I think that it's most likely due to a sound driver issue.
I'm looking for a good quality Audio Interface for my iMac, i work with MIDI only so i won't be needing tons of ins & outs for vocals, mics, live instruments etc, the only thing I'll be needing to connect is a Digital Piano (MIDI ports) and a pair of Monitor Speakers. what are the best AI brands out there for a iMac ?
did anyone ever got a chance to work with Saffire LE on XP using bootcamp? I searched all over the place, found some patches and solutions, but nothing works Just ridiculous.
I bought a new MacBook yesterday, downloaded Logic 9 and installed the USB drivers for my Saffire 6 USB audio interface but cannot locate it in either the system preferences or the Logic 9 audio preferences. How do I get this working ?
I've recently purchased a spanking new macbook pro and am keen to lay some tracks down in garageband. I need a cheap but good quality audio interface so's I get get my guitar riffs onto the mac.
I have, since a couple of years ago, used a nice little gadget called Kanex XD. It is simply an HDMI to Mini Display port, which allows me to play Xbox 360 on my iMac 27 ". It has always been clear as a bell!
When I decided to buy the thing, I was not sure if it would work with my current sound system. But it did! I run all the audio from my mac through a firewire audio interface called Focusrite LS 56 (from the audio interface I have Yamaha HS80M, info for geeks like me).
The audio has functioned really well through my Focusrite. But when I updated to the latest OSX (10.7.4), the audio from my Xbox only plays through my internal speakers. Otherwise, the sound works as usual. It's only when I play my Xbox through my Kanex XD, the audio goes through the internal speakers.
I guess it's something that happened in the new update that makes it impossible to play the sound from my Xbox through my audio interface. I contacted the Kanex XD support. They said that there's nothing they can do and that it probably have something to do with the update.
I can’t record an audio (vocal) track. Here is my gear, DAW: Reason 8, Mac running Yosemite (version 10.10), mixer: Behringer 1204 USB (with built audio interface). I’ve also tried the following stand alone audio interfaces, TASCAM US 100 and M-Audio Fast track Pro. Key board Axiom 25. I gone into preferences and selected USB Audio CODEC for both output and input on the MAC, did the same under reason preference audio tab. when I create a audio track in Reason, in the audio input section I see “No audio input”.
When I select the drop down menu there is a section for Mono input and Stereo for me to check this is followed by a grayed out section that states “No audio input available, please check your sound card settings. The other funny thing is when I use Garage Band, I have no issues recording. I just recorded in garage band using the Behringer 1204. Am I missing some simple setting somewhere,missing a channel routing.
Lately when I go to view backups using the Time Machine interface it lists all my backups going back to April 22, 2009, but anything older than late August 2010 is blacked out and can't be clicked.
When I look in my Time Capsule disk on the finder, all the older backups are there and I can view and copy all the files.
Also, in system preferences, Time Machine preferences lists my oldest backup as April 22, 2009 and there is plenty of disk space available on the Time Capsule.
Why is this happening and what can I do to fix it?
information: MacBook Pro 2.4 GHz Intel Core 2 Duo OSX 10.6.4
I'm wondering if I somehow have a bad firewire chip in my MBP. It hasn't been able to work with firewire audio interfaces.
- I tried a Metric Halo ULN 2 which loses sync with it's audio. It will be fine for a few minutes with itunes but then becomes distorted and ringy as if it's lost it's audio sync. - Random kernel panics while using Logic 9, Garageband 11 with an Apogee Duet - all software fully updated. One time it froze while not doing anything - logic was simply open and sitting there. Using iTunes through the Duet seems fine. - Pops and crackles using Presonus Firestudio.
I've tried wiping my software and reinstalling everything. I'm using a MBP 5,3 2.8Ghz Core 2 Duo 4GB RAM, Snow Leopard (10.6.5) with the latest updates. I'm going to try an Apogee One which is USB, but I'd really like to use a firewire interface. If there's something wrong with my firewire port, I'd like it taken care of. My machine is under applecare 3 year warranty. I don't think this is an easy thing to prove though.
I successfully installed XP via Bootcamp and my XP audio software Sampitude. I did also install the MOTU traveler using newest drivers. However, it does not comply perfectly. I was installed alright, but when using it, it doesn't work properly. MME seems to work, but doesn't. ASIO doesn't work at all. Basically it crashes the program, but if you just unplug it, everything works fine again, using the internal audio.
just got happy about the fix for the audio / performance problem of the 09 mac pro's. Why should it be different, the next problem knocks at my door, hallelujah...
When I connect my external audio interface (apogee ensemble) to my mac pro, the mac begins to whistle...
As soon as I turn off my interface again, the whistle is away immediately . The sound is definitively coming from my mac pro and I couldn't locate the problem to a fan. I think it's maybe the firewire controller chip? When I connect my external lacie HD I have no problems at all. I have tried it on both ports on the back side with no success.
The whistle is not constantly on the same noise level. Sometimes it's away for a few seconds, it's high pitched and really annoying though. It does not matter if I playback audio or not. Nothing worked though. I experienced the whistle in the past few months sometimes but it was mostly just for a few minutes or so. But in the past few days it was constantly and it never really stopped. This drives me crazy when I have no audio playing and my room is silent !!
I have no other firewire cable (400 to 800) around to test it. Could this be the culprit also?
I am using iTunes with a Tascam US-122L audio interface. It worked perfectly fine until yesterday evening, and now iTunes absolutely refuses to play any music when the Tascam is connected. I click a song title and the diamond slider does not move, the song stays at 0:00, and the "play" button doesn't change to the "pause" button. It seemed to have started doing this after I exported a song into iTunes from Audio Hijack, which I downloaded to capture some audio from Logic Pro.
I've tried everything, from restarting my computer, to reinstalling the Tascam drivers to reinstalling iTunes.
iTunes works just fine except for the "playing songs" part, which is it's major selling point. It works perfectly fine when the Tascam isn't connected.
I've heard of a lot of people with similar problems but none of the solutions I've seen have worked. Anyone got any ideas?
Today I connected my Mackie Onyx Satellite Firewire audio interface to my 2.4 Ghz 13" Macbook Pro for the first time. After it had been running for a while, I looked at iStat Pro, and it reported a CPU temperature of 67C, which is about 15 to 25 degrees hotter than this machine usually idles. Now I've looked around a little bit and found that it's a known issue and associated with the Agere Firewire chipsets. Is there any solution for this? Does it make a difference if you use a daisy chain setup with an external hard drive in between the computer and the audio interface, or a repeater cable, or anything of that nature?
I hope I'm not double posting. Have any of the other new iMac owners experienced weird frequencies coming from external speakers that are connected to their iMacs?
For example: I have a set of studio monitors that are hooked up to my iMac using a firewire audio interface. Whenever I'm copying data I get an extremely high-pitched frequency coming from my speakers that sounds like my hard drive spinning. Also, whenever I'm scrolling or moving the magic mouse I get a loud buzzing coming from the speakers (especially when scrolling). None of this stuff happened with my previous 20" iMac C2D. I have experienced this issue with all three of the 27" iMacs that I have gone through thus far (due to the yellow tint issue). Does this sound like something I'm just going to have to live with. All of these high pitched frequencies are driving me batty!
I noticed my sound wasn't working, so I did a restart. The "blip" sound when you adjust the volume using F11/F12 would play, but as soon as I tried to run something else (YouTube video, iTunes, etc.), that wouldn't play (just get stuck at whatever point I tried to start it). After that, the blip sound no longer worked either.
I have tried the following things already and none of them fixed the problem (all of them reset the "blip" sound, but it always went away again as soon as I tried to play anything):- running Apple Diagnostics (no problem detected)- resetting PRAM- resetting SMC
I've checked things as suggested in other message boards … there's no red light in my headphone jack, nor is the sound muted under System Preferences. The problem persists whether headphones are in or not.
I have hooked up[ an m audio 2626 to my imac. drivers have been downloaded, followed all the steps. computer is not seeing a connection to the firewire port. When i connect to my macbook pro, no problem. How do I get a connection to the firewire on my imac
I have a few .AVI files that I want to play on my Macbook. But when I play them with Quicktime, it shows me a black screen and plays with only audio. No video. And yes I have installed Perian but that's not fixing this problem either. I tried using VLC but that didn't even show me a black screen. I could only listen to the audio.
The audio on my 2006 MacBook has recently stopped working. I thought the internal speakers might have blown, but the audio doesn't work even if I use headphones or external speakers through the headphone jack. When I use the volume control buttons, everything looks normal - I don't get that symbol that it seems most people do when their audio isn't working. The levels will go up and down but without the sound usually associated with the volume control. I checked out the sound option in System Preferences, and everything is normal. I'm running OS X version 10.4.11. I've tried rebooting and nothing changes. All the other threads I've seen seem to have that symbol when using the volume control, or something is different under System Preferences, but everything is normal.
i have recently bought a speedlink spes clip on microphone i plugged it into the 3.5mm jack on the side of my macbook air then i went into system preferences and clicked on sound. then output... but there wasn't anything showing where as if it was showing i would have been able to select my microphone output and not the actually macbook mic. but my new device plugged in isn't showing and i can't use it. i checked the packaging and it says system requirements mac.
On a day-to-day basis I run: Adobe PS, INDD, and AI, Microsoft Entourage, Firefox and iTunes. Just recently, after an upgrade to Leopard, I added Things and Simplify Media to the list.The problem that happens before (on Tiger) and now (on Leopard) is command+tab switching stops functioning and Expose hot corners and shortcuts stop working.
I'm pretty sure this isn't a Finder crash because before, on Tiger, I could quit+restart Firefox and everything would be back to normal. Almost as if some shortcut had causes the system to act differently or there was some app dissonance?
But now, with Leopard, nothing I quit will cause these two features to act properly until I do a restart. Both features (command+tab switching and expose) are very necessary for my work flow. I have checked SysPref to make sure keyboard shortcuts are default and Univeral Access to make sure assisted devices is turned off.
I want to create a digital file from a cassette tape.I cannot hear any audio through my iMac system speakers when I send the cassette audio into the audio input jack (mic). Using mid-2011 iMac running OSX 10.7.3
I have just updated OS X to the newest ver. 10.7.3 and WI-FI conection stops when computer sleeps. Using internet conection through Time Capsule. Someone experienced the same?
