Software :: White Screen Hang On Mac OSX Startup Disk?
Mar 20, 2010
Running a MBP (mid 2009) 2.26GHz on OSX Leopard 10.5.8. I am trying to boot from the Startup disk (OSX Leopard 10.5.2) and when I stick it in a restart, I hold C and it hangs on the screen before where the Apple logo would appear normally, as if it's trying to load from the startup disk. The disk spins up and I hear it, but it just hangs there. Only thing I can do is a hard restart with the power button.
I have started from the disk before, so I know it worked in the past. Also, OSX recognizes the disk when I'm logged in and I can even run the Installer (ask you to restart though).
I recently turned on FileVault (have restarted multiple times since then) but not sure if this has anything to do with it. I am trying to set a password for the Firmware so someone can't reformat without a pw.
Last two days, I notice that my MBP gets stuck at the white Apple startup screen until I reboot. I've also notice getting the beachball, even when using Firefox.
I got an old G4 and cleaned it up and hooked it up to a monitor, but when I start it- it shows the white startup screen and then just goes to black and i can't get an image on the monitor again. The computer is running and responding to the keyboard though
When I shut down my iMac and restarted it gets past the apple logo then turns white and starts dimming and then getting brighter but will not go any further.
I tried to reboot in safe mode and it done the same thing. I power cycled by unplugging the holding down the power button.
Whenever I on my MacBook it gives off this white screen as seen in the pic. I tried command+r and holding down the option key on startup but it still leads me to this white screen.
My MacBook Pro gets stuck at startup, the screen goes white every time and even when i shut it it's still stuck white and the apple on the back stays lit.
Info: MacBook Pro (13-inch Mid 2010), OS X Mavericks (10.9.3)
I was off of my iMac for an hour or two so my screen saver when on. I went to wake the computer and it was frozen. I tried using the keyboard and mouse to wake up the computer from the screen saver, but it would not work, so I powered the iMac down manually from the button on the back. I let it sit for 15 minutes, then I tried to start the computer up again. Now at start up, I get to a blank white screen with the spinning moving pin wheel, and that is it.
I have a mac pro running leopard (purchased in 2/08) and it was running beautifully for almost 2 months with no hangs, crashes or freezes. Then, for some reason, today when I turned it on, it would not boot. It would get to the apple logo, then just sit there for a few minutes, then reboot itself and the same thing would happen.
I pulled out the ethernet cable, unplugged all usb except keyboard/mouse and it would then (sometimes) boot into the system, log me in and present me with the UI. I then quickly performed a soft reboot and it would get to the desktop. However, I can only use it for anywhere from 30 seconds to 5 minutes before it would completely lockup. The clock freezes, the mouse freezes and it just sits there forever. I have tried booting into Vista (BootCamp) and it also freezes before startup is complete....................
I have a 13" macbook pro, i was using it one night and was runnung ok until i come back to it the next morning.I opened the lid but the backlight didnt come on but could just see the screen so i re-started it by holding down the power button and then thats where it never worked again for me. I have followed some of the tips from some forums but i have no luck.i used another hdd for my mac to use on as its bigger GB than the original,ive been using that for 5 months with no problems, now my mac wont show any of the hdd's even the orginal one that wasnt formatted. Ive managed to format the original one but its not showing that one niether.the second hdd ive left with the snow lepard on it. Now with the other mac ive plugged them both in externally and shows up on desktop but still no luck on the mac thats down. Ive even tried with the installation cd that shows up on startup management but nothing eles.
Info: MacBook Pro (13-inch Mid 2009), Mac OS X (10.5.1)
can anyone tell me why my screen on my imac is all white? the last time i use it was 6 months ago because i had to move. so i unplugged it and now i wanna use it again but when i turn it on, it's all just white on screen, i try to reinstall everything by using the disk but still nothing, can anyone tell me what's wrong with my computer?
i bought a 13" Macbook Pro (mid 2009) last week and i bought the 2gb/160gb moel. I have upgraded the memory to 4gb and today my 2.5" sata Western Digital Scorpio Blue (500gb) arrived, i followed the steps and replaced the hard disk, however when i turn the machine on i just get a blank white screen, i inserted the Install disk that came with it and i was instructed by the apple staff to hold the c button to book the disk, this doesn't seem to work, also i cant eject the disc either and i have tried holding down the trackpad while starting up.
So my 20" 2.4 Imac crashed on me twice tonight. A box popped up telling me to hold down the restart button for several seconds to restat. The second time I did this it just sits with a white screen and give three loud beeps over and over. Is there a fix for this? Is it my ram? I'm at a loss.
My step mom has an iMac. The first gen intel one and the other day out of nowhere there was a white screen with a folder on it and now when you go to start up the iMac the screen just stays white.. What would be the cause of this and what should I do to fix it .. thank you
macbook pro blue screen with spinning disk, won't start up. my macbook was really sluggish so i ran a hardware test. it said NO PROBLEMS. i did restart. my current login and password were REJECTED. then the macbook went into blue screen and it just sits there and flashes to gray and back to blue and the white lines that make up the circle icon just spin and spin.
My brother's iBook G4 (I think it's a 2003 model) has a problem with the screen. When the computer is turned on, the screen stays black, although the backlight is on (the apple glows). Sometimes, on start up, the screen works normally for a random amount of time before going fuzzy and then black again.
Any ideas on how to fix this? Is it likely to be a problem with the hardware in the actual computer, or just the screen? Or is it a software thing?
I've begun to notice a ring, roughly three inches in diameter, in the middle of my Air, Rev C, Screen. It is a white ring, a couple of millimeters thick, that I can see best behind an all white screen, i.e. a blank page of a word processing document.
My 27" iMac, running OS 10.6.8, has started running slowly when loading Apps and when running Safari. Also, when powered, on It has started stopping on the grey screen before the Apple logo displays. To get past this I must turn the Mac off and then back on.
I've begun to notice a ring, roughly three inches in diameter, in the middle of my Air, Rev C, Screen. It is a white ring, a couple of millimeters thick,that I can see best behind an all white screen, i.e. a blank page of a word processing document.
Anyone seen anything like this before. I can actually see part of it right on the white of the page I am typing in this thread.
When I go to front row, all my video content plays sound, but the picture is just a pure white screen (shows the slider to move chapters, etc., but the screen is just white).
Any ideas for solutions? I did google searches, etc., to no avail. I have a MP (not early 08), which I upgraded the graphics card to a 2600XT, and it's running Leopard.
Tried everything from archive and install (wouldn't read disk2 until the 9th try and ended up with 9 system folders). Then tried an Erase and Install. Still it refuses to boot. Get's hung up at the blue screen. Will only boot in safe mode. Now for the last few days even the startup chime is missing. Tried PRAM and NVRAM resets. no help. Won't boot from DiskWarrior boot disk either. Just hangs
iMac Specs: Machine Name:iMac G5 Machine Model:PowerMac8,2 CPU Type:PowerPC G5 (3.0) Number Of CPUs:1 CPU Speed:1.8 GHz L2 Cache (per CPU):512 KB Memory:1 GB Bus Speed:600 MHz Boot ROM Version:5.2.5f1 Serial Number:QP52604RSDU
Yesterday I switched on my macbook (Leopard) and got the flashing question mark. Ran all the resets and booted with disk utility which encountered an 'Invalid B-tree Node' when attempting to repair the disk. Additionally, the SMART status was verified.
I ran DW 4 last night, and performed the hardware tests which reported that the disk was operating like normal. The majority of my media files and additional work is backed up to my Time Capsule but I still have a folder of papers that are relatively new, and wanted to retrieve. While DW managed to reconstruct the majority of my drive (there seemed to be 15g missing - but it's just music files) including this folder, it couldn't replace the disk, as it encountered 'Serious Disk Malfunctions'.
So, via the Disk Preview I want to transfer my saved folders to my TC, but I don't appear to be able to locate it (via ethernet) through DW - even if it's connected when I boot up in DW. So, first request is: Can I connect to my TC to transfer across in DW's preview?
Second is: What are my options if DW can't replace? Do I need to take it into Apple and get a new HD (it's out of warranty)? It's possibly worth noting that I'm a student and have absolutely no money - so cost effective options are a bonus!
I get this question mark along with a folder when starting up. I tried holding down the option key when turning on the power and then I get an internet recovery along with a globe. I click on the arrow below it and it takes maybe 15 minutes to start up. Then i get this disk utilities screen. I'm now unable to do anything. When going into disk utility, disk 0 shows with Mac OS X base system underneath it. All the clickable buttons are faded out. Is there something wrong with the hardrive? and where could i get this fixed? There isn't a warranty on it.
I'm trying to repair my hard drive. I restarted from the OS X Mac Mini install CD (holding down the letter C when I heard the chime), opened Disk Utility from the Utilities folder, selected my hard drive image, but the "verify disk" and "repair disk" options are grayed out. I'm at a loss as to how to proceed.
