When I shut down my iMac and restarted it gets past the apple logo then turns white and starts dimming and then getting brighter but will not go any further.
I tried to reboot in safe mode and it done the same thing. I power cycled by unplugging the holding down the power button.
Info:
iPhone 4S, Mac OS X (10.7.2)
I have a white screen and a blinking world
Info:
iMac, Mac OS X (10.7.3)
What o I do I have done command, option, p, r at start up etc. I will not go to the desktop.
Info:
iMac
My iMac starts up to a white screen and stays that way and won't start.
Info:
iMac, Mac OS X (10.7.3)
I was off of my iMac for an hour or two so my screen saver when on. I went to wake the computer and it was frozen. I tried using the keyboard and mouse to wake up the computer from the screen saver, but it would not work, so I powered the iMac down manually from the button on the back. I let it sit for 15 minutes, then I tried to start the computer up again. Now at start up, I get to a blank white screen with the spinning moving pin wheel, and that is it.
Info:
IMac 2Ghz Intel Core Duo, Mac OS X (10.5.7)
I am running OSX 10.5.8. A little while ago I successfully Boot-Camped my hard drive and installed Windows 7, but i recently got a new hard drive. I copied over my OSX partition successfully, but didn't copy over the Windows partition. On my new drive I went through the boot camp assistant and created a partition and inserted the Windows 7 disc. But when it restarts, it just seems to hang there- it's just a black screen with a blinking white underscore(_).
I have been told that because I copied over my OSX partition it didn't set up the MBR on the new disk, is their any way to fix this? (besides doing a clean install of OSX)
Are there any software or guides available to help me fix this?
My MacBook has just a whitegrey screen with a blinking "?".
Info:
Aperture 3, OS X Mountain Lion (10.8.4)
The other day the screen started blinking randomly. It'll flicker for a few seconds and then go white with vertical grey lines for a few seconds. Then it will go back to normal. There doesn't seem to be a pattern to it. Sometimes it will go through that process for five minutes and then stop. Other times I can be working on it for hours and nothing will blink or act screwed up.
View 7 Replies View RelatedJust came back from the Genius Bar at Apple Amsterdam. Both iTunes and iPhoto had problems launching and libraries were not loading. Ruled out hardware problems so they tried installing OS Snow Leopard over my 10.5.8 in a way to keep my documents safe. All went well until halfway it said it couldn't install succesfully. Made a new appointment for in 3 days from now. They would then overwrite the current OS with the new one so i should go home and make sure to back up all my files in the meantime. Problem is that when i came home and started my laptop i got a blank/white screen with a blinking documents folder symbol with a question mark in it! Does anybody know what it means and will i be able to ever make a back up of my documents?
Info:
MacBook, Mac OS X (10.5.8)
I type in my password and it goes to a white screen
Info:
MacBook Pro
Last two days, I notice that my MBP gets stuck at the white Apple startup screen until I reboot. I've also notice getting the beachball, even when using Firefox.
View 11 Replies View RelatedI got an old G4 and cleaned it up and hooked it up to a monitor, but when I start it- it shows the white startup screen and then just goes to black and i can't get an image on the monitor again. The computer is running and responding to the keyboard though
View 7 Replies View RelatedWhenever I on my MacBook it gives off this white screen as seen in the pic. I tried command+r and holding down the option key on startup but it still leads me to this white screen.
Info:
MacBook, Mac OS X (10.7.2)
My MacBook Pro gets stuck at startup, the screen goes white every time and even when i shut it it's still stuck white and the apple on the back stays lit.
Info:
MacBook Pro (13-inch Mid 2010), OS X Mavericks (10.9.3)
Running a MBP (mid 2009) 2.26GHz on OSX Leopard 10.5.8. I am trying to boot from the Startup disk (OSX Leopard 10.5.2) and when I stick it in a restart, I hold C and it hangs on the screen before where the Apple logo would appear normally, as if it's trying to load from the startup disk. The disk spins up and I hear it, but it just hangs there. Only thing I can do is a hard restart with the power button.
I have started from the disk before, so I know it worked in the past. Also, OSX recognizes the disk when I'm logged in and I can even run the Installer (ask you to restart though).
I recently turned on FileVault (have restarted multiple times since then) but not sure if this has anything to do with it. I am trying to set a password for the Firmware so someone can't reformat without a pw.
My iMac's HDD is fried. The computer just froze so I decided to reboot it and was presented with that lovely blinking question mark folder. I tried it again (and every time since) I get the good old apple logo on the grey screen with the spinning loading thing, but it never progresses past that.I threw in my old Leopard install disc and it asks me where I want to install Leopard, but the HDD option never appears, nor does it in Disk Utility. So what do I do now? It's Sunday where I am (Melbourne, Australia).I'm not too sure if it's still covered under the AppleCare Protection Plan. Should I take it to an Apple store? I remember when my mouse broke I tried taking it there and they told me to take it to some authorised repair place. I'm not too excited about hefting the iMac to the shops only be told they can't
Info:
iMac, Mac OS X (10.5.8)
I have a 13" macbook pro, i was using it one night and was runnung ok until i come back to it the next morning.I opened the lid but the backlight didnt come on but could just see the screen so i re-started it by holding down the power button and then thats where it never worked again for me. I have followed some of the tips from some forums but i have no luck.i used another hdd for my mac to use on as its bigger GB than the original,ive been using that for 5 months with no problems, now my mac wont show any of the hdd's even the orginal one that wasnt formatted. Ive managed to format the original one but its not showing that one niether.the second hdd ive left with the snow lepard on it. Now with the other mac ive plugged them both in externally and shows up on desktop but still no luck on the mac thats down. Ive even tried with the installation cd that shows up on startup management but nothing eles.
Info:
MacBook Pro (13-inch Mid 2009), Mac OS X (10.5.1)
Holding option doesn't work, taking out the battery doesn't work, running out of ideas.
Info:
MacBook, iOS 5.1.1
I'm a relatively new Mac user. In fact, I haven't had that much experience at all. I work in a donations store and today we got a donation of an iMac. I searched around a bit and I'm sure it's a G5 model. It looks like [URL]. It looks to be in great condition, no scratches, not even a fingerprint on the monitor.
However, when I turned it on, after plugging the power chord in, I started experiencing problems. The fans kicked on and I heard the chime (I assume that was a post?) but I was getting no video and the white LED on the front of the screen was flashing on and off. The exact pattern is strange - I don't think I've see it before. It flashes once, then stops, then flashes again, then stops. Over and over. No sequence. :| The computer did not come with a keyboard or a mouse. I was testing it to see if it actually worked, before I bought the keyboard and the mouse, so I'm wondering if it has something to do with that? I'm not really sure.
How do I change the iTunes screen display from 'white on black' to 'black on white'
Info:
24" iMac
I have my laptop which is Powerbook G5 version 10.3.9 Panther. For the last two months the PB didn't boot up and it was beeping three times and white lid blinking.After going through internet i notice the problem was RAM and i need to change it. I bought another RAM 1GB (the old one was 512MB) and inserted it in the lower RAM slot.
Thank GOD the mac boot up properly and everything was fine. I charged it to full capacity and shut it down.The next day i started my mac as usual but surprisingly it beeps three times and it didn't boot up again.I open the RAM cover tried to remove it and replaces it again but it didn't work out and i am totally devastated and i don't know what to do any more.The brand name of the RAM i used is TRANSCEND.
I have a G5 dual 1.8 power PC...Bought some ram put it in & booted up. Then a red light came on the logic board behind the power button. The machine wouldn't turn on....I called apple care & we rearranged the ram, now the red light is gone but my system still won't boot up. The white power light blinks every few seconds... the apple store told me sorry can't help because your machine is vintage. Even if my logic board is fried is there a place to buy one on the cheap?
View 5 Replies View Relatedive noticed a small glitch during the startup of my macbook pro. Whenever I log into my account before it displays my desktop, a window flashes for a split second that has 2 options to choose from (It looks like whenever my cubase crashes and it prompts me with the options "Reopen" or "Sent report" or something like that) I never manage to exactly see what this window is as I cant read it in time, let alone choose an option. It just switches off quickly. All software updates are recent, and this really bothers me. I dont know what it is. Could it be a virus? Im very careful with what I download online, let alone the websites I visit. The OS itself works fast and on track.I decided to run disk utility and check the hard disk for errors. Turns out there were a few permission errors, and disk errors where it said my MacOSX volume is corrupted. Ive only had this laptop for 6 months, I dont want to send it in to apple just yet. I've run lion recovery since after a backup and fixed the permission and disk errors, then re-verified them and it said everything was now fixed and fine. I restarted and that window STILL flashed.
Info:
MacBook Pro, Mac OS X (10.7.2)
So I kinda want to explain my saga of my (late 2009) Macbook Pro.
I got the first generation of the MBP shortly after it came out.... I actually purchased it on Black Friday.
Anyhoo-
-The specs:
-15" Glossy Screen
-2.4GHz Intel Core 2 Due
-2 GB 1064 MHz DDR3
-NVIDIA GeForce 9400M
-Toshiba 250gb HDD
(So as you can see, pretty basic machine.)
Anyway, I'd only had the computer a few months when I started getting the blinking folder on startup. I brought it in, and they verified the HDD was going bad, so they gave me a new HDD. About a month later, I had the same problem happen again. The "Genius" I talked to said it was probably my Logic Board, so they replaced that. However, after getting my computer back from the shop, on my first startup, I got the blinking folder. So I TOOK it back AGAIN, and they replaced my HDD again.
A few months later, I started having issues with both the HDD not spinning up and my USB affecting my iSight camera (weird I know) so I brought it in again, and they finally just replaced my whole computer.
Everything worked great for a while, until once again, I started getting the flashing folder on startup, I took it in and they replaced my HDD again. (Yeah, this is like HDD number 3 for me now)
Since then, I have had the HDD replaced two other times, along with my superdrive, and MagSafe adapter.......I'm not exactly liked at my local Apple Store.... they know me by name... I don't exactly like going there anymore...
I also want to note that I literally baby my computer; I almost polish it daily, and am extremely careful with it
So my current list of repairs looks like this:
� 5 HDD replacements
� New Logic Board
� New Super Drive
� MagSafe adapter
� New Computer
ALL that being said, I plan to sell my computer as soon as Apple Care expires; I can't risk having a flakey computer on my hands... I can't afford to pay for all the repairs. My Apple Care will expire next December, so I'm hoping I can sell it around late December- early January and be just in time for the new MBP refresh, which I'm hoping that year will include possible:
Slight redesign
Lighter computer (in weight)
Faster (of course)
Possibly retina display
Why I'm posting all this is mainly just because I wanted to hear if anyone else has had anything similar happen to them.... I'm a sucker for when it comes to first generation Apple stuff, but now I know.
Been on a Mac in one form or another but never saw this. It's not even mentioned on the apple.com site under startup problems. Started up on my eMac and got this blinking blue dot that looked a bit like earth in a gray square. Whole think was about an 1" square in the middle of the screen. The startup tone was normal.
View 2 Replies View RelatedI acquired a Unibody MacBook that experienced a little water damage. The logic board was definitely shot, so I replaced that yesterday and initially the machine was working like a champ, save for a few issues:
1. The machine tries charging my battery, but eventually gives up and decides that there is no battery in the machine (there is a battery in there, and it shouldn't be dead yet, should it?)
2. I've been experiencing an issue in which the MacBook and charger aren't getting along. I've got two different chargers, both of which work on my pre-Unibody MBP consistently but sometimes I'll plug one into the MacBook and get no light, and in other cases I'll plug it in and get just a very faint green light. In either case, the machine won't start up. I usually tinker with the machine for a few minutes, taking the back plate off and checking connections, waiting a few minutes, and it's back up again.
3. Before the machine starts up, the LED blinks three times. I initially thought this was just a blink pattern to notify the user that the logic board doesn't have a serial number yet, but I've run the serializer and entered a SN in, and it still does that. Is this normal for these Macs?
I know that these MacBooks are a little more intricately tied to the battery than previous Macs. Does anyone think the above problems (at least 1 and 2) would be solved by a replacement battery? Or does it sound like something else is wrong (perhaps the DC in board)? I've never heard of anyone needing to replace a Magsafe DC in board (and from their low prices online, I'm led to believe that they rarely fail).
So my 20" 2.4 Imac crashed on me twice tonight. A box popped up telling me to hold down the restart button for several seconds to restat. The second time I did this it just sits with a white screen and give three loud beeps over and over. Is there a fix for this? Is it my ram? I'm at a loss.
View 1 Replies View RelatedMy step mom has an iMac. The first gen intel one and the other day out of nowhere there was a white screen with a folder on it and now when you go to start up the iMac the screen just stays white.. What would be the cause of this and what should I do to fix it .. thank you
View 21 Replies View RelatedI just installed a new hard drive in my mac ibook g4 - but when I turn it on I still get the blinking folder with a question mark.
View 6 Replies View RelatedI'm getting a blinking folder with a question mark on startup. What is it?
Info:
MacBook, Mac OS X (10.4.7)
