I have an M8439 800/1.5/160/DVDRW 10.3.7 / 9.1 classic. I want to run Digidesign Pro Tools v5.1, which requires OS9 and an IDE HD to record to. I have purchased a WD Caviar SE - EIDE HD Question: can I just run it inline with the operating (boot) HD off the ATA bus, or do I need to get an IDE PCI adapter card?
View 2 Repliespls be patient with my English, i'll try to do my best.
Finally i decided last week to upgrade an old Powerpc G4 733 Quicksilver (model before 2002 vers.)
I changed combo with a good Pioneer dvr-112d.
Now i'm asking u an indication: find a video card better than nvidia mx 32 installed with two important targets
1) Should support wide screen 1680x1850
2) should support core image tech in order to work better with last Tiger.
reading around i'm sure fx5200 satisfy nr2 but doesn't support wide, ati like 9600 had big problems of compatibility with my G4 model.
Pls could u point me to the right way ?
wich is the best video card compatible with a 733 ghz quicksilver ?
About Hard disk, one more question , i have 128 gb limitation.
I'm not gonna change the controller, is there any chance to mount a 7200rpm 16mb 250gb for my system ?
Uses for G4 Quicksilver?
Just bought it yesterday, have Puma on it currently, gonna upgrade to tiger when i get the disc.
What could i use it for, Server? iTunes streaming?
I want to make my PowerMac G4 (Quicksilver 867) wireless using a USB device so I can get the higher speeds. Can anyone recommend a specific card they know works with my Mac? If anyone is interested I did a search and couldn't find what I was looking for.
View 1 Replies View RelatedI purchased a used ATI X850 XT AGP 2-slot for PC, not the single slot found as OEM on PowerMac G5s. The goal is to flash it with the equivalent Mac bios so that I can use it in my Mac G4 867MHz Quicksilver (2001). By the way, I already know that I have to cover up pins 3 and 11 in order for an 8x AGP card to work in my Apple 4x AGP slot.
View 5 Replies View RelatedI just set out to initialize the drive of my old G4 800 DP, using the system disc. Everything began fine but when I returned the screen was black, and video wasn't being picked up. I decided to force reboot and start over, but now I cannot get my mac to boot at all. Black screen with no video. Cannot boot from firewire target drive. Machine won't recognize system disc. When I boot there is no chime. I hear the machine apparently working hard to read the system disc but nothing happens and it eventually ejects the disc. I've tried 3 different discs, so I know it's the machine not the disc. Pressing "option" at startup has no effect. I also know it's not my LCD, as it works fine with my other machine. Anyone have any idea about what's going on here and what I can do to regain access to my machine?
View 4 Replies View RelatedJust picked up a minty Power Mac G4 Quick Silver and two ADC Studio Displays. I'd like to hookup both displays, but I only see one ADC port. What's my lease expensive dual ADC display option for this machine?
View 5 Replies View RelatedI have a G4 800mhz quicksilver, with 2 hd's and a cd burner drive. I just got the machine and I like it a lot but it is so loud. I don't know why it is so loud but I was wondering what I could upgrade in the machine to make it not so loud.
View 6 Replies View RelatedI can't seem to find specific information that would tell me if a 1.25 GHz processor from a MDD G4 would swap into a G4 Quicksilver (733 MHz) I have sitting in a corner.
They are both single processor machines, but I question the compatibility. I don't have the MDD machine with the 1.25 GHZ processor yet, so I can't look at them both for comparison.
Why were some Powermac G4's names have Quicksilver in them? Is it a special line or what? Whats the diffrence between the G4 "Quicksilver" and the regular g4?
View 10 Replies View Relatedmy G4 quicksilver has resently decided that it doesnt want to work. when i press the power button the light and fans come on but then cut out again after about a second. any ideas?
View 4 Replies View RelatedI was hoping to install 3-1GB PC-133 168-Pin Non-ECC non-Reg SDRAM Memory in a Quicksilver G4. Would this memory work?
G4 Quicksilver 1.8 GHZ 2TB Sata Raid.
Do i need a Raid card to install a SATA hd for this model (quicksilver). Or can i just get a converter cable (IDE ATA-to-SATA).
View 3 Replies View RelatedMy SATA RAID card is conflicting with my 6800 GT Graphics card in my 2002 Quicksilver.
View 7 Replies View Relatedusing a MBP in a target disk mode i got the G4 to build, but on its own, the folder with the question mark appears blinking I want to know how do i get on lookign for the right PCi IDe card? Would any do?Is the Fw400 Card a better option? I guess putting a system disk in an external through firewire isn't gonna do it?
But getting a PCI firewire would? is it fasterAm not to sure what i want to do with the machine once i get it working. Maybe put it at my folks house, about time the got to learn the MAC OS x.
My hard drive from my G4 733mhz wont mount at all. The ? in a blue folder just appears. I have tried to start up from an external mountable drive and the ? again appears. When I disconnect the internal hard drive completely and boot from my external drive it boots up.
Prior to this problem I took the hard drive from my G4 733Mhz and put it in my G4 867Mhz computer to load a new disk image. I did this as I didn't have access to an external mountable drive then. After doing this the hard drive doesn't mount in either computer and when connected all other mountable drives wont mount. I have the internal drive set to master.
Recently I didn't do my research, and I purchased a Quicksilver power supply to put on a Gigabit machine. I noticed it had four extra pins which look like some of the ones they use to power processors in some PCs (tho I've come to find this is for the ADC port). I dug a little deeper (Googled "powermac_g4.pdf") and found out that some of the pins have differences between the Gigabit PS and the Quicksilver PS.
Has anyone else had an experience like this? Will the PS work without any wirecutting or do I need to get a new one?
Just want to know the proper type to replace it with. Is there a size (gigabyte, not physical!) limit I need to be concerned with?
View 5 Replies View RelatedI have two drives in my Quicksilver 2002 G4, one is a 250GB which can be fully used, the other an 80GB. Can U rid both of these drives and install two SATA 1.5TB drives? I do not want to use the PCI slots for a SCSI card and wire additional drives that way, because the transfer speed will be limited to 40mbps I believe. I have a Sonnet card a dual PPC 1,8Ghz card, a PCI USB 2.0 card and have other open PCI slots, but finally ran out of storage, and have a use for this machine to hold a LOT more. Other than the transfer speeds possible on SATA, are there any other differences between the original IDE (ATA) drives? Do they connect the same way?
View 9 Replies View Related I am wondering how I go about removing my Hard Drive from my Power Mac G4 QUicksilver? I don't know the first thing about removal or location of the HD?
It is a 40GB Ultra ATA/66 (5400 rpm)
I would like to remove it and fit it with a Hard Drive case enclosure so I can use it as an extra external for backing up data.
I was told by Tiger Direct that this enclosure should work:
[URL]
I would ultimately be connecting to a macmini for backing up data periodically.
I would like to upgrade my 17" Powerbook G4 to wireless n, but I'd like to upgrade the internal airport extreme card instead of using a PC Card adapter.
Are there any options for this?Will this airport extreme card from early model MBPs work?
my specs:
17" pwrbk Hi-res
1.67 G4
late 2005 model: Powerbook 5,9
I am buying a G4 Power Mac. I was wondering if anyone knows what the capabilities are of this computer. Can the RAM be upgraded to 2 or 4GB? Graphics card? As far as I know, Leopard can be installed so I am good with the OS. Oh, and a friend told me the Power Mac is like a Mac Pro but older. Is this true? Like can the Power Mac house multiple processors and hard drives?
View 14 Replies View RelatedI have a 450mhz powermac g4 that I am using for a simple file server in my house. I was wondering if there are any pci cards that have mac drivers, that would work. In order to steam movies and stuff, the card probably has to support 802.11g.
View 2 Replies View RelatedI posted this on the buyers guide forum but got no response. Maybe you guys can help.
I have a G5 dual 2.0 with 5.5 GB ram and an ATI Radeon 9600 pro graphics card.
I have been running Final Cut Studio with no problems. Once I upgraded to FCS 2, it seems to drag with some of the new fetures. Motion 3 seems really slow! So I added 2 more gigs of ram to bring it up to the 5.5.
I am waiting for the new MP like so many of you, but I will keep this computer for off line editing and compressor and for a part time assistant editor to use.
Would it be worth it for me to upgrade the graphics card?
If so what would be a good choice of card for this type of work.
FYI the last computer game I played was Zork, so I don't care about gaming.
I had recently purchased a 2nd hand G5 PowerMac with dual 1.8GHz processors and PCI-X slots. I think it was released in November 2003. It's a great machine, but suffers from its lacklustre 64MB graphics card. My Mac man told me not to bother, but I would like to investigate the option further. What do you think is available and where would I obtain one of these things? Oh, I should also ask the most important question...is it worth it?
View 10 Replies View RelatedI have a power mac G4. My tech man says I have a generic wireless card installed. I have tried to use internet connect but it does not see it. Also when a do a summary of the network the card is not detected. Finally, no Airport option ever comes up to connect to. It is not available. Anything I can do or do I need to find a mac pro in my area?
View 2 Replies View RelatedI have a dual 2.0 PowerMac G5 without a video card. I also have an old GeForce4mx 64 MB video card lying around from a MDD. I was wondering if I could use that card in the G5, just to test for functionality of the computer. I'm wanting to avoid putting any unnecessary money into it just incase it doesn't work.
View 3 Replies View RelatedI just got a G5 power mac (dual 2.3GHz) and bought one of these: [URL] as an airport substitute. When trying to install the card it doesn't appear to fit in the PCI slot. Am I right in thinking it should fit? Since it's a PCI card and the G5 has PCI/PCI-X inputs?
View 3 Replies View RelatedI asked this earlier but, never a decent answer and a few people asking if I have PCI-X and PCI-Express mixed up which made no sense for what was being asked.
I have a PCI USB2.0 card rev2.2 that I removed from my old G4 MDD.
I upgraded to a used G5 2ghz DP (M9032LL/A) system which has "three open full-length PCI-X slots: one 133MHz, 64-bit slot and two 100MHz, 64-bit slots" from what the specs on [URL] says.
I was told that a PCI rev2.x card will work in a PCI-X slot but when I tried the system didn't even power on.
So... should it work? does it matter which PCI-X slot? or was that guy confused between PCI-X and PCI-e?
Hoping it will work because 3 USB ports isn't enough when you have a WACOM, Scanner, Printer, Mouse, Keyboard, USB Drive, etc...
Does anyone know if its possible to install a video card with more than 256mb of RAM in a 2.7 dual G5? (8xAGP and PCI-e) Iv'e read lots about flashing ROM on cards but they all seem to be 256 - is there some limitation on flashing bigger/newer cards?
View 4 Replies View Related