Power Mac :: No Update With PM G4 MDD 1.25DP
Jun 21, 2012
I bought recently (this week!) an PM G4 MDD 1.25DP with radeon 9000PRO, 1.25G of RAM, combo drive and two hard drives with 200 gigas both of them. This is my first Mac! I'm realy in love with it.
The first one is:in the morning when I try to start my G4, only after 30 or 40 attempt I get it. I push the power button so many times.... I pull away the power cord in same "so many times" until the Mac "wake up". After that it's work especially fine. I can shut down and restart the Mac unexceptionally.
The second one is: when I try to update the Leopard and when they ask me to reboot, the progressing bar showed never headway. But others updating, e.g. the Itunes, proceed like a workaday.
Info:PowerMac, Mac OS X (10.5.1)
View 6 Replies
ADVERTISEMENT
Nov 23, 2007
I have a problem described by Apple in document Power Mac G5 (Late 2004) 1.8GHz models stop responding randomly.
How can I update the firmware because my G5 1.8 screen is blank? Thought that I could make my G5 1.8 as a hard disk for my MacBook, or I may try to update over the network. Is there a risk of corrupting my MacBook if I try?
Information:
G5 1.8
Mac OS X (10.4.10)
McaBook
View 1 Replies
View Related
Mar 8, 2009
My macbookpro (leopard) is freezing during Macosx Update, It asks for a reboot, then the timeline stays forever in the mode "configuring setup..."... I can still access to volume control and brightness shortcuts but thats all.
the timeline is blocked. only solution is to power off manually!
I can't update leopard... Did you experiment this also?
View 2 Replies
View Related
Mar 21, 2012
How do I get IDVD to run on OS X 10.5.8? Get msg. " you can't use this version of IDVD with this version of MAC OS X"
Info:
iMac, Mac OS X (10.5.8)
View 1 Replies
View Related
Nov 15, 2007
During installation, my graphics got all screwed up. You can see a screenshot of what's going on at this link: [URL]. I'm actually writing on the defective computer, so it's hard for me to see what's in the screenshot. Here's what I did so far. I tried removing half of the RAM first, then the second half, the problem persist. I rebooted on a different system, it's still there (so not software). I tried Hardware Test utility, it says everything is fine. I unplugged the Video Card, cleaned it a little along with the connectors, nothing. It happened DURING the update to 10.4.11 (not after I rebooted). I'm pretty sure I can take screenshots of it, so it's not simply in the connectors to the monitors. It happens on both my monitors (also when I unplug one of them).
Information:
PowerMac G5 Radeon 9800 Pro
Mac OS X (10.4.10)
View 7 Replies
View Related
Dec 19, 2007
We just updated our G5s here at the lab (QuickTime and Garageband ), and now the sound output is extremely distorted and crackly regardless if its a video on cnn or a song off iTunes. Tried Zapping the PRAM and repairing permissions, even reinstalled QT from the standalone installer on apple to no avail.
Information:
MacBook Pro
Mac OS X (10.5.1)
View 3 Replies
View Related
Apr 2, 2009
I got up and tripped over the power cable and It popped out (thanks magsafe! ) but the computer immediately shut down. I plugged it back in and started it up to see my clock was messed up. I changed the clock and redid the update. Everything seems to be working now but I was just wondering if anything else could have happened?
View 2 Replies
View Related
Apr 23, 2012
how can i update the firmware/bootrom to 4.2.8 for my power mac g4 ( gigabit ethernet) ? i am using mac os x 10.4.11, and dont have a disk with mac os 9.
View 11 Replies
View Related
Jun 27, 2012
For some bizzare reason my Mac wont restart or update, not to sure when the problem started as I normally just put it into sleep! But basically when I click update it says the updates need the Mac to be restarted, I click ok. It basically logs out and goes to the Username screen to login. Same story when trying to restart/shutdown; just goes to the login screen.Â
I'm tempted to do a OS Wipe and start Fresh! However it's going to take 3 hours to download the latest OS! Patients isn't my strongest point !Â
Info:
MacBook
Pro, Mac OS X (10.7.3)
View 1 Replies
View Related
Nov 4, 2007
CDs will boot fine, blank DVDs will mount fine, but when I insert a DVD movie; the drive won't mount and the DVD player will not play my discs. DVD Movies Not Played after 10.4.10 / DVD Player 4.6.1 Updates. I currently have a Pioneer DVR-109 installed in my PowerPC G5.
Information:
PowerPC G5 Dual 2 Ghz
Mac OS X (10.4.10)
View 7 Replies
View Related
Feb 5, 2012
Had a power failure while the iMac was doing updates. Now I have a white apple screen and the grey spinning wheel on start and that's all I get. What do I do now?
Info:
iMac, Mac OS X (10.7.3)
View 5 Replies
View Related
May 15, 2012
I have updated quciktime as instructed and I can no longer access or even open my itunes?Â
Info:
PowerMac, Mac OS X (10.5.8)
View 3 Replies
View Related
Jul 2, 2012
After using Open Firmware Update my G4 went into a crazy circle. At first, it was impossible to start up, and when it was possible, just for a couple of seconds, and then the translucent screen asking you to restart the computer pressing for a few seconds the start up button.
Info:
Quadra 605, G4 Desktop, IMac 500, eMac, iMac G5 PPC, iMac G5 Intel, Mac OS X (10.5.7)
View 6 Replies
View Related
Jun 30, 2012
I purchased a G5 in 2005. Never once used the drive for DVD. So I decided to use it today, and it doesn't work. I tried to burn a DVD that didn't work. The drive doesn't even recognize it. I did some research, I came to the conclusion that I have to update the pioneer d112 firmware. Seems simple but the pioneer update is for windows format!
Info:
Mac Pro, Mac OS X (10.5.8)
View 6 Replies
View Related
Apr 30, 2012
Can I update this machine with Leopard or Snow Leopard?
View 2 Replies
View Related
Mar 19, 2008
My girlfriend has a 12 inch Powerbook G4. She noticed that the battery life was starting to dwindle. Tonight, she tried using it. It wouldn't power up. The battery indicator showed one flickering power circle. The adaptor has the green circle on it, indicating the battery has a full charge. However, the computer won't charge up.I've read the 12 inchers don't have separate PMUs. Could that prevent the machine from starting? She was using it earlier this evening, as she e-mailed me pictures from our vacation.
View 10 Replies
View Related
Feb 10, 2008
I have a iBook G4 laptop and there seems to be something very wrong with it. It started a few days ago just randomly. I was reading something on the internet and the screen went black on me, but the power was still on (I clicked CAPS LOCK to see if there was power). I then proceeded to push the power button and the power went off. When I pressed the power button again to turn it on, it made that internal noise it always makes and then the fan came on, and wouldn't turn off. There was no picture on the screen at all. Completely dead. But there was power, because when I clicked on the CAPS LOCK, the light came on). I tried pressing on the power button for at least 15 seconds and even went as long as a minute, and the power didn't go off.
View 3 Replies
View Related
Apr 18, 2008
I had a bad power surge (USB hub that was plugged into the back of the display had the wrong power cord plugged in... very stupid mistake I know!!) take out my 23" Cinema Display. The display shows no sign of life (no power light, etc) and the brick has been tested and is OK. My local service place says that they will have to send the display back to Apple which means a minimum of $400 for repair so I'm wondering if anyone has had a similar issue that they resolved successfully? The service place suggested that Apple would replace the logic board but is there any way to test to see if this is the main issue? I have seen logic boards sold separately online but would be hesitant to buy it without know that this would fix this issue.
View 10 Replies
View Related
Nov 8, 2007
I made this a new topic because I think it is important enough to do so. Probably most of those that originally complained about this have moved on to the new MacPro but I am sure there are still enough G5 owners out there that still have concerns about this topic.
A clean install of Leopard eliminates the infamous power supply beeping
Its amazing, my G5 is like a new machine; no more of the annoying power supply beep; although, I learned to live with it after a while and didn't even notice it. However, the silence is now very noticeable.
View 2 Replies
View Related
Nov 19, 2007
Where can I obtain a new 23 Inch Cinema Display power adapter? I've searched the Apple Store but I cannot find it.
Information:
G5 Dual Core PowerPC
Mac OS X (10.5.1)
23 Inch Cinema Display
View 1 Replies
View Related
Jun 19, 2010
I have found that by plugging in my Apogee Duet firewire audio interface and ONLY WHEN AppleFWAudio was loaded there was a 10c CPU raise that was making my MBP (late 2008) hot!I wanted to monitor the power that was required for Duet to run and to see if the temperature rise was due to that, so:With Apogee drivers uninstalled (just to be sure its not their drivers related, which is notMBP on battery power with System Profiler opened (to monitor the mA required by the computer from System Profiler -> Power)
View 5 Replies
View Related
May 29, 2012
a friend recently gave me a g5 power mac that had some issues, and the failure was described as intermittant. The machine supposedly would work properly when booted and start freezing up after time, but if turned on the next day it would work properly for some time. I assumed it was an overheating issue, but apperently there is more to the picture. I have tried booting the machine quite a few times and the display always reads no signal. The machine sounds as if it were booting normally, but there is not output. At first I assumed it was my display cable, which was a DVI-D single link, however the DVI-D dual link cable leads to the same result. Is it nessicary to have a DVI-I cable? None of the error LEDs light up on the motherboard. After doing some hunting I haven't found anyone with the same issue, but I am wondering if I should assume the graphics card is dead. What steps do I need to take to isolate a graphics card failure in a power mac g5?
View 3 Replies
View Related
Oct 8, 2007
I hav" a "late 2004" G5 2.0 dual processor. To upgrade graphics card, I find many require a power supply splitter. Do I have a molex 4-pin connector? I can't see the location inside the box.
Information:
G5 dual 2.0, 2.5Gb
Mac OS X (10.4.3)
View 1 Replies
View Related
Nov 18, 2007
I have the problem that I need to frequently power cycle (shut off and on) my dsl modem to maintain a reasonable speed with my internet connection. It is making the internet experience pretty user unfriendly. Does any one know whether there is a way to optimize my internet connection such that this is not required so frequently (couple times a day)? I am on my second dsl modem, and the same problem has occurred with each of them. ATT simply advises me that my solution is to power cycle the modem to sync the system, whatever that means.
Information:
Power Mac Dual 2.0 GHz
Mac OS X (10.5.1)
ATT DSL Internet Connection
View 4 Replies
View Related
Dec 6, 2007
I added 2 sticks of 512 to my power mac g5 1.6. I had ahard time getting the computer to see the new ram, but finally was able to kinda get it working after zapping the pram. However my computer only saw these 2 sticks as 256, odd. So i attempted to troubleshoot the problem. I tried just installing the new ram, but the computer wouldnt boot. I tried a few different combos with the other 4 sticks i had, but nothing. I put the old memory back in, and still nothing. The power led looks to blink once every five seconds or so. I tried pressing the pmu reset button, but still the same out come. I also tried taking out the battery, nothing.
Information:
1.6 g5 single proc
Mac OS X (10.5.1)
View 15 Replies
View Related
Dec 13, 2007
I had a weird issue this morning. I started computer and it did not make the chime sound, it didn't do anything at all. I disconnected it from the extension cord as well as all the peripherals attached to it and nothing. I tried a different start up disk and again there wasn't a sound. Then i unplugged it and reset the SMU on the mother board and air sprayed the computer to remove all dust. Then plugged it back and it came back on.
Information:
Power Mac G5 Dual 1.8
Mac OS X (10.4.11)
View 5 Replies
View Related
Oct 7, 2006
I'm using a B&W Power Mac G3 with 512MB RAM and OS X Tiger for a SMB file server (with 5 users) and a USB printer server. Everything is working good, but I have a problem.
It doesn't have a monitor or keyboard/mouse attached normally (I can configure it via VNC). The problem is that I would like to be able to turn the machine off when it's not needed (like at night sometimes, days when I won't be home, etc.). I would like to just hit the power button and have it turn off, however it puts it to sleep instead.
Normally, sleep would be fine, except on the B&W, the fans still run, just the HDs shut off, so it's still noisy as heck.
Is there a way to make the power button shut it off? If not, any other easy methods of shutting it off you can think of? Via VNC won't cut it, as my dad needs to be able to turn it on (not a problem) or off as well.
View 9 Replies
View Related
Mar 21, 2009
i just got my new imac 2 days ago. I was wondering is there another to turn on the power without pressing the power from button? (cuz i remember u can power on from the keyboard b4)
View 7 Replies
View Related
Jun 26, 2009
Anyone know where I can buy an extra AC cable for the MagSafe 85W power supply that came with my late 08 MBP? I'd like an extra cable and I'm not interested in ponying up the dough for the entire power supply. I checked the Apple Store and Macmall, but haven't found anything as of yet.
View 3 Replies
View Related
Apr 9, 2012
Last Thursday I down loaded software updates from apple and have been losing power very quickly ever since. It just seems like as soon as I remove the power cord I lose power with in three minutes.
Info:
MacBook, iOS 5.0.1, purchased feb 2009
View 4 Replies
View Related
