I have a new unibody macbook pro and print from it using a wireless hp officejet pro 7410 all in one printer. I have a linksys wrt150n router. My pc laptop prints fast from it but the mac prints very slow. The printing actually stops for a while then starts again. It doesn't seem to do this all the time. I can't figure out what would slow it down.
View 2 RepliesI have a Linksys Wireless Router and a Linksys Modem, the router is 6 years old or so 802.11b, how much faster would the Internet be if I had a combined Linksys wireless router/modem versus the 802.11b that I have now?
Would I see a huge difference? I am running my Macbook off it and an olde Toshiba laptop.
I want to fully convert to the apple eco-system but can't afford the new airport extreme right now. Model number of the used airport is EbM8799LL/A
View 8 Replies View RelatedI had a DLink DIR-655 Wireless N router and my wireless was running very fast, 9.7MB using [URL] with no lag looking up sites. I had to upgrade the router since I was hosting a site and the router wasn't working properly for that.
So, I bought a Linksys WRT610N Dual Band router. I have the iMac running on the 5GHz band and it runs around the same speed.
HOWEVER, when I open Safari or Firefox, in the status bar, it says "looking up google.ca..." or whatever site I'm browsing for and can take up to 5-10 seconds before it starts to display the site. When it is on the site, browsing around is fast as long as it doesn't change domains.
ANOTHER HITCH, I have VMWare's Fusion installed on the iMac and Vista installed there and there is no lag to browsing a site. When I type in the site, it immediately goes to the site and I am able to browse fine.
Any thoughts on this?
i really want a new iMac but can't afford it right now. so i was thinking of getting an older iMac to replace the pc we have now. if i do do this can i use the wireless router that i have now with an iMac G3 or G4?
View 6 Replies View RelatedI have several questions before I make my purchase. I've got 2 computers in my upstairs bedroom that are wireless. I currently have a Wireless router which is a Linksys WRT54G.
It's already getting on in age so I was thinking of replacing it with a better wireless router. I'm deciding weather I should go with a Linksys N or go the apple route.Will I get faster internet if I go with a Linksys Wireless N? What is the difference between G and N?I was thinking of getting a Time Capsule because I wanted an automatic backup of my data.Is a time capsule going to perform the same as a Linksys? Which router is better?
what is the difference between Time Capsule and Airport extreme. Are they basically the same with the only difference being the hardrive?If I get a Time Capsule then do I still need a Linksys router? Is it easy to setup a wireless network using a Time Capsule or Airport Extreme? Is it easy to configure as a Linksys?
I have a Linksys wireless router set up (WRT54G) and my PC desktop and laptop connect fine to the internet with wire and wireless. I installed an airport card in our Power Mac G4 but this cannot detect my wireless network. I have it connected now with an ethernet cable running through the kitchen but want to get rid of the cable.
Is there a compatibility issue with airport and a Linksys wireless network? The Mac recognizes the airport card so I hope that means that it is good. (I got it from eBay used) This Mac is the farthest away from the router so I guess my next try is to see if I can move the router a little bit closer.
I am a newbie to wireless so possibly I have a setting wrong. I did tell the router the mac addresses of all of the computers that I want to connect.
Any advice?
Imac and iphone lost internet connectivity via Linksys wireless router. Ehternet works fine. Keep getting note about "self-assigned" ip. Ideas? I have tried everything I have found and read.
Info:
iMac, Mac OS X (10.6.8)
i'm currently using the linksys w610n router thru wifi, i'm experiencing very slow internet speed on pages loading on safari but when i tried to download files on igetter, it goes on full speed
View 2 Replies View RelatedSo I recently bought a Linksys WRT160N to replace an old router in my house. The network worked fine with the old router before it died... Browsing speed was great, download speed was great. Now that I have the WRT160N however, my network speeds have plummeted. And it's JUST my MBP... the rest of the computers in my house are Windows PCs and they are surfing away at supersonic speeds compared to what I'm getting on my MBP.
At first I thought it may be the wireless security (WPA) so changed it to WEP... no change. So then I just disabled it altogether... no change.
The Windows PCs are getting speed of about 2000 Kbps whereas I'm getting between 150 and 500 Kbps. I've already replaced the router once...
Is there anything I can do, or is this router just not going to play nice with Mac?
BTW- I have a 2.2 SR MBP
So I have a wireless router from cox cable (motorola surfboard SBV5220). I also have my airport extreme base station connected to the wired ethernet in the other half of my house. So I have the cox motorola router hard wired to the ethernet in-wall outlets. And When I plug my computer directly into the ethernet plug in the walls it works great and fast. So I have the airport extreme plugged into the ethernet port in the wall to use wireless on the other half of the house that the motorola router doesn't reach very well.
Everything worked great until the motorola router went out one day and we had to reset it. Once we reset it, the wireless internet from the airport extreme started acting up. Half the time it works fine and just as fast as it did before. The other half it doesn't load a full page. It's not even working at all really. I tried to see if the problem happens when using the internet from the motorola router, but it wasn't consistent. Sometimes the airport internet worked fine while the motorola was in use on another computer and sometimes it didn't. I haven't been able to figure out a consistent cause.
I also had the airport express plugged in as a wireless extended for the airport extreme, but I took that out as it was pretty unnecessary. Also, I got a new mac mini and need to run it off the airport extreme wireless also. When I turn off the mac mini and use my macbook with airport extreme the problem still persists.
I tried google-ing and then searching on this forum and got many unrelated topics. I would really appreciate anybody pointing me in the right direction. I am a semi-newb when it comes to networking, etc...
How long do these routers usually last for? I've had mine for less than a year and I believe it died today.
For the pasta few days I've had to unplug and plug back in to get a connection and today - nothing.
I was getting tired of my belkin54g router that kept dropping connections, so I went and got a new linksys wireless G router. I popped in the CD, followed all the instructions and when I get to the end of the install it says that the configuration was successful, but it could not verify an internet connection.
I figure it's just a hiccup and try to connect with my laptop via airport- success! I get my homepage. But then, I can't get to any other page at all.
It says it can't find the page, but my network connection in system preferences says I'm connected. I go to my desktop which has the hardwire connection and I can't get on the internet at all, but again, my network connection in system preferences says I'm connected- green light, IP address and all.
So I figured I did something wrong and restored the factory settings on the router. Same thing happens again. WTF? This should have been easy. What the hell is wrong with this thing?
It should be noted that if I type in my IP address, the router info comes up immediately. I am also just connecting my modem to my desktop to post now. My internet connection works fine.
I'm new to Macs. I live ~200 yards from my Mom's house. I set her up with a b/g/n router. My Imac picks up the "n" signal just fine. My ps3, which only does b/g, gets no signal. I have an old linksys wrt54g wifi router. I tried plugging it into my imac and setting the imac to internet sharing through ethernet, but it didn't work. Stringing an ethernet cable isn't an option. Am I missing a step in the system preferences for internet sharing? Is there another way to get internet to the ps3? I would rather not buy any new equipment, but I'd spend up to $50.
View 2 Replies View RelatedMy router is a WRT54GS with DD-WRT firmware. It works fine with my old eMac (w/ original airport) and every PC in my house, but not with my new iMac (w/ airport extreme).
At first I thought I might need to power cycle it, but it didn't work. Then I thought it might be conflicting with something, but that wasn't the problem. On a side note, I also have a WRTU54G-TM for VOiP phone. It works with both Macs equally, unlike the GS. The only problem with that one is it will randomly kick my Macs off the network and I end up turning off airport and turning it back on when that happens.
I've a Macbook, PS3 and Linksys ADSL Gateway that can be put in Bridge Mode.Macbook is connected to the internet via 3G USB modem.I was able to tell Macbook to broadcast it's 3G internet connection via AirPort and use it from any other Machine, such as iPhone.
But the problem here, is that I want can't use it in my PS3, because it's the old 20GB model which doesn't have a wireless connectivity.So, I figured out that I might be able to tell Macbook, to share it's 3G internet connection with the Linksys ADSL gateway while it's out in Bridge Mode, and this gateway can send the internet connection to PS3, all using Ethernet cables, as follows:
Macbook --> Linksys ADSL gateway in Bridge Mode --> PS3
But I couldn't make it work.
This is what I've done so far:
1- I plugged the Ethernet cable from Mac to Linksys ADSL gateway
2- I put Linksys ADSL gateway in Bridge Mode
3- I plugged another Ethernet cable from Linksys ADSL gateway to PS3
4- I went to network preferences in Mac and choose the Manual settings
5- I gave the Mac the IP address: 192.168.1.101, Subnetmask: 255.255.255.0, Router: 192.168.1.1 and DNS: 192.168.1.1
6- I went to to PS3 wired settings and gave it IP: 192.168.1.102, same setting with other fields as Mac Ethernet
7- While testing the connection in PS3, the IP check went successfully, and the internet didn't
Note: I do not want to connect Mac to PS3 directly via a croseeover cable because I want to share the internet connection in mac with Xbox 360 as well, which also doesn't have a Wireless connectivity.
I just bought a Powerbook G4 from my school and the internet is sparatic but it is just at my house. I went to my friends house on Friday and it worked fine and at my school it does to. When I get home it either doesn't connect or goes from four bars to two bars. I have a Macbook and that works fine with the internet. I have tried re setting the router and nothing works. I have a Linksys router.
View 2 Replies View Relatedis there a way that I can lock the linksys Wireless connection from my MBP?
It's been an open connection so users or neighbors around me can use my connection and it seems to be slowing my connection down.
I was looking at how I could secure my connection through my computer?
The Linksys router has a static ip set up to work with the DSL connection and desktop. My macbook pro connects to the router but there is no internet connection! This is pissing me off becuase my mom's cheap Dell notebook connects flawlessly but My $2500 macbook pro doesn't. What do I need to do?
View 5 Replies View RelatedI've always used airport express but lately I've been noticing big drop in speeds when I'm in the upstairs rooms. I do not feel like spending $175 on another apple router, how much trouble is it to go with linksys? How much settings configurations will I be getting myself into?
View 8 Replies View Relatedi want to know how instal Linksys router WRT54G in Mac Os x Snow leopard 1.6
View 4 Replies View Relatedi had my friends white book and when i opened the air port it found the linksys wireless G router i had had connected but it didnt ask me for the password.
I know i set a password for the linksys router because when i log on using my HP it ask me for the password.
Question is what did i do wrong? or are the linksys wireless routers not the best things to use with the mac?
I just bought an AE and replaced my older Linksys with SpeedStep router and for some reason the internet seems slower.I did a speed test to compare with my older system and it's night and day how much slower it is now.
With the Linksys I was getting from 10-15Mbits download.With the AE I'm just tested and got 700KB down Anyone have a clue as what I can do to speed it up?By the way, the AE is connected directly to my desktop by ethernet cable.
Our company is currently running an Apple Time Capsule that has ~40 users wirelessly connecting to it. Now we recently opened up a new office space that will potentially have more than 50 users that need to connect to our network.
Seeing this we then purchased a Linksys WRT610N wireless router so that we can facilitate more than 50 wireless users. My question therefore is: how do we set this up so that the Linksys router connects to the TC so that we will subsequently be connected to the Internet as well as our network - no matter what SSID (TC or Linksys) we're on. I've been bearing about bridge modes and WAN ports but this is new to us so a brief explanation/procedure would be appreciated.
Keep in mind that we would like to keep the TC as our main router with the Linksys connected to that as well as increase the TC limit of the 50-user connectivity limit.
I got an old Power Mac G4 Quicksiver 2002 a little while back and I decided to upgrade it a little bit as a pet project. One of the things I did was add an Airport Card so I could get wifi. I read all about 802.11b and WPA2 and all that, and I can't say I understood it all, but what I think I DID get was this: The old airport card cannot connect to a WPA2 network. (right?) I looked at the settings for my router, and it said it was on "WPA2/WPA Mixed Mode." I thought it would work. When I went to connect, it said "WPA Network Needs a Password. I put in my password, and after trying to connect for a little while, it said "Connection timed out." Right now I am connected to the "guest" network, which needed no password. Just to test, I changed the encryption to just WPA, not mixed mode. It stopped my PC from getting wifi, and still didn't work on the Mac. I got it to work by putting NO password, but I really don't want that. Should I try to change it to WEP? I'm not really a tech type of person, especially not with wifi stuff, I'm kind of just stumbling around with Google...
The router is a Linksys E2500 router. AirPort Card Information:Wireless Card Type:AirPort Wireless Card Locale:USA Wireless Card Firmware Version:9.52 Current Wireless Network: {other network name} Wireless Channel:11 Is there any way to connect to the password protected network?
Info:
PowerMac, Mac OS X (10.5.8), Airport Card
Having issues in setting up my Apple Extreme + Apple Express to my Linksys E2100L ROUTER/NETWORK. I have Green lights on my extreme and express with the Linksys router having the extreme attached to the router (ethernet) with express in another room for my Blu-ray. The Linksys does not see the Extreme or Express. I am using WPA2 Security on the Linksys router. How can I get the Linksys to see the Apple Extreme/ Express? Is there something I need to do on the Linksys end or on the Extreme/Express so that they can talk to each other?
View 4 Replies View RelatedI just got and airport card for my old mac, and want to use it with my network. but it won't work with my network.
Info:
ibook (14.1 LCD 900 mhz 32 vram), Mac OS
X (10.2.x)
I've recently come back to apple mac's, however before my new G4 ibook, i had a few pc's set up on a network, i've still got them and i want to add my ibook to the network, i've got most of it working, however my laserjet 4M plus which has a print server installed in it, which works perfectly with the pc's doesn't want to work with my new ibook. My ibook is connected via airport to a linksys access point, and that to the router, which in the connected to the laserjet. I can Ping the router and it all seems fine, but getting it to print just isn't happening.
View 2 Replies View RelatedWhen I connect my iMac directly to my cable modem (no router) I get fast speed. But when I connect my laptop through my Linksys WRT54G v5 router the speed drops to about 20-40 kbps.
What is causing this dramatic drop in speed?
WAP Personal security
MAC filtering enabled: Yes
Channel 6
DHCP Enabled: Yes
Autoconfiguration Enabled: Yes
What kind of configuration could help me to get fast speed? I am newbie so don't know to make deep configuratons!
I have a WD Mybook Essential Edition external hard drive that is dedicated to the Mac that I am trying to connect through USB to my Linksys router (WRT 610N).
I have spent no less than 14 hours on the phone with Linksys, can't get through to Western Digital, and Applecare tells me they don't work with PC hardware.
