So I installed osx 10.4 server on a Power Mac G4 (white/blue)
Went throught the setup screens and did a complete reformat / install.
Just boots to the loader screen. (Where the mac face shows, followed by a question mark) and just cycles over and over.
I can put the DVD in at this point and restart the install.. I did go in and check the disk permissions and disk status and both passed.
I'm running a late-2008 Macbook Pro with OSX Mavericks. I installed a new battery, and the computer will not recognize it. I've heard that I should reset my PRAM and NVRAM. I have already reset my PRAM, but my problem continues. I have removed the battery/pressed the power button for 5 seconds, held the power button down during boot,I cannot access the open firmware.
Info:
MacBook Pro, OS X Mavericks (10.9.4)
Yesterday my screen (30" Apple Cinema) started showing symptoms of graphics card failure, jagged lines across the screen. I rebooted my Mac Pro and it was gone. Then it happened again an hour later, this time the machine didn't boot, I get the Apple logo, and then it hangs up and the screen is shifted to left (I get apple logo on left side of the monitor instead of the middle) and jagged lines all over.
So the first thing I tested was using Target Disk Mode, it works. I can access my Mac Pro's internal HD's by TDM from my MacBook Pro. Then I tested single user mode, it does boot, I can't read what's written since the screen is shifted to left, but if I type (without seeing) reboot and hit enter, it reboots. So I assume the single user mode is working.
What else can I try to 100% make sure it's my graphics card that failed and everything else is ok with Mac Pro? I already ordered a graphics card replacement but I wouldn't like to be surprised if the Mac Pro still doesn't boot when the card arrives. It won't boot from Apple Startup DVD either. Same thing happens, gray logo then kernel panic with jagged lines all across the shifted screen.
Mac Pro
Early 2008
Model Identifier: MacPro3,1
Processor 2 x 2.8 GHz Quad-Core Intel Xeon
Memory 16 GB 667 MHz DDR2 FB-DIMM
Graphics ATI Radeon HD 2600 XT 256 MB
Software OS X 10.9.4 (13E28)
Boot ROM Version: MP31.006C.B05
SMC Version (system): 1.25f4
This is the first time I've encountered this. Upon cold booting the machine it went directly to the legacy Mac OS X Server login screen from before the upgrade to Mavericks. It would not let me login with current credentials. I had no choice but to hard power off. It returned to normal operation on restart.
It could be a possible bug.
Info:
Mac Pro, OS X Mavericks (10.9.4)
I have an iBook G4 1.07 GHz 30 gb 256 RAM with Panther. It was working fine until my HD got close to being full. Now I can't get it to boot past the Apple screen. It will either freeze there, or move on to the blue screen and freeze before the progress bar enters. I want to re-install Panther but I can't get any CD to boot during startup by holding "C", including the Panther OS CD, the Hardware Test CD, or the Tech Tool CD. I am able to boot to single user mode, where I type fsck -fy, and I recieve no errors with the hardware. I had this issue beore and my HD had to be replaced by Apple.
View 6 Replies View RelatedIs there a way to make the Boot Camp menu the default boot screen, as opposed to holding Alt? This is the latest SL release, if that matters.
I know this is possible in some manner, our networked iMacs all do it; they start up and give the option to boot OS X or Windows, with a countdown to boot the default OS. I'd just like the same thing to happen on my MBP.
Today I came home from work and turned on my Mac Pro. At first everything appeared normal and I walked away on a call for a few minutes. Out of the corner of my eye I noticed the screen was flashing to black off and on. I turned off the tower to try and restart it and now it wont boot!
I have removed all other hard drives aside from the boot drive. Re-seated all RAM. Tried various combination's of RAM. Tried to load the snow leopard install only to get a kernal panic. Tried again with just RAM and received a kenal panic as well.
*Update* It seems that the RAM when I swapped it out was VERY hot for only being in a short period of time (under 10 min). Not sure if this helps.
trying to boot in Leopard my Mac Pro will get the the gray loading screen with the "loading circle" and just sit there forever. Than after a bit it will just stop and the whole computer can shut itself down. I just installed the 8800gt upgrade kit last week, and have had no problems at all for the past week. The only thing that changed that may be related is the 8800GT XP Driver. I installed the latest beta driver for it under XP in boot camp because it wasn't working properly with the default boot camp drivers. So I can correctly boot in the XP via boot camp, but trying to boot in Leopard it just hangs at the gray loading screen.
View 15 Replies View RelatedThe other day my 1st gen MBP functioned without any probs, until it suddenly powered down. After I removed the question marks from my eyes, I offcourse tried to reboot it.
But it never makes it beyond the grey screen, sometimes untill the apple logo, sometimes not even that far.
Offcours I googled around first to gather some info before I decided to put this problem down on this board. I found this could be a HDD failure, but in those cases, with other people, it could be powered holding apple + s, and doing some checks that way.
Mine doesn't even come that far
I have a second hand 1st gen MBP with upgraded HDD and RAM, snow leopard, and coincidently since last week no more battery... so i may have powered down a completely unprepared mac by tripping over the wire, once or twice...
I've got a 2010 i7 15.4 MBP, after installing boot camp drivers from MAC OS DVD, I could not find any option about how long to dim screen brightness. However, my friend's 13.3 MBP does have. What about yours, guys?
View 4 Replies View RelatedMy macbook pro won't boot past the grey screen, I've tried reseting PRam, running fsck from single user etc to no avail. All signs would point towards a hard disk failure, but the curious thing is that it sometimes mounts in disk utility when booting from the install CD, so theres a little life left in it yet! I have fairly recent backups of most of my files, but there are a couple I've been working on in the past few days that won't be backed up. So my question is this - is it possible to copy files from my mac HD onto a external drive through the terminal/disk utility while booting from the CD.
View 6 Replies View RelatedI own an iBook G4. I could not get it to boot up, it would just go to a grey screen with the apple symbol and a timer/clock that looked like a gear.FYI: I may provide more information than necessary in the text below. I'm not sure what is and isn't relevant.
Following some advice I found in this forum I got out my old OS disks to boot from the disc instead of the hard drive. I intended to archive the old hard drive and install my latest OS (10.4.6 on the disc, 10.4.11 was the version I had been running on the machine, I believe). The machine told me it needed 4.5 Gb to install 10.4.6 Tiger, but I only had 4.0 Gb left on the hard drive. So instead, I archived and installed with the OS that came with the computer originally, 10.3.4.
I got things going, did the archive and install, and got to the log in screen. Unfortunately, I could not remember the password, so I booted up in single user mode, and entered the following to get into the machine:
1. mount -uw /
2. rm /var/db/.AppleSetupDone
3. shutdown -h now
This got me in with a new admin login, and I started up in 10.3.4. I soon noticed that I could still see all of the files that I put on the hard drive on my old operating system. I thought I shouldn't be able to see them, but since I could I decided to try to copy them to an external hard drive. When I did, I got an error message saying that there was a read/write error. I was not entirely surprised, but I decided it was time to turn back to the forums for help.
What I want to do is copy everything from my old hard drive onto an external hard drive, make room on the iBook hard drive to reinstall my latest operating system (10.4.6). Once I've done that I'd like to get the essential files back onto the iBook from the external hard drive and continue using my computer (even though it is a dinosaur).
I just bought a powerbook, and I'm trying to get it to turn on. It doesn't have a hard drive, so obviously it won't be able to get it to boot. I just want to be able to get to the flashing folder. When I press the power button, the computer does nothing, not even the fan spins. The only indication I have that it is on is the caps lock light turns on. I've tried resetting the pram, but the screen stays blank and does nothing. I don't have any ram modules in it, so it shouldn't be a ram problem.
View 11 Replies View Relatedmy macbook pro won't start up...it begins to boot up but stops short before the screen comes on. the light which indicates that the computer is on dims and the booting.stops.
Info:
MacBook Pro
I woke up to my MacBook fan going nuts. Had an error message on the screen that said something about a disk error. The machine wouldn't do anything (force quit, launch app) so I hard powered down. Now.....NOTHING. All I get is the white screen, followed by the flashing folder. Here is what I have tried so far.
I already booted from the restore cd that came with it and opened disk utility. The hard drive shows up as something like disk1 but not "Macintosh HD."Tried to repair permissions and got an error message. Thought then to do an archive and install......and the HDD isn't even a viable option to install the OS on.
I had the original (but smaller) HDD that came with my MacBook, so I put it back in and everything booted up just fine and is back up and running. (Thank God for MobleMe that had all my contacts, etc on it). But I still have some info on that other HDD that I need. I ordered a usb enclosure for the drive to maybe try some recovery, but it seems to me that the HDD failed or something. Is there anything else I can do?
So I've got a powerbook G4, thats 8 days past its warranty. Conveniently, it now won't turn on. It won't wont boot from CD. If I turn it on, I get a gray screen that usually just turns my computer back off, if thats not the case I get a screen that shows the finder icon and a question mark and then turns off.
All it will do is boot into open firmware mode. Currently the install disc is inside of it and I've tried booting the cd using "cd:, bxi" and "dir hd", and it can't open both. Does anyone know how to wipe the HD, and start the installer using firmware? Otherwise, I think I'll have to take out the harddrive and plug it into an external case and then wipe it.
In my attempt to install Windows XP via Boot Camp, I accidentally inserted an SP1 disc instead of the SP2 disc that I have. The installation proceeded to the point where it does for most who attempt this: the screen where you are prompted to press ENTER. I could not proceed and therefore restarted the iMac and held down the mouse button upon start-up to remove the CD.
HERE IS THE PROBLEM:I can not boot into OS X because the keyboard shortcuts (those that might allow me to select which partition to boot from and/or reset PRAM) seem to be disabled. Instead, a reboot always ends at a black screen with a blinking DOS-esque cursor, or the prompt: "No bootable device -- insert boot disk and press any key."
I have attempted inserting my SP2 disc at this point, to no avail. My keyboard seems to be disabled, as if the SP1 install proceeded just enough to establish itself as the boot drive without drivers for the keyboard. I've tried using all 3 USB ports, disconnecting other USB devices. Oddly, my bluetooth mouse works to eject the CD on reboot...
I've been reading this site for a while now, first time I'm posting. I recently purchased 8 GB of RAM for my 2010 13" MBP. There are two 4 GB DDR3 PC3-10500 1333mhz sticks. When I install them in the laptop my computer does not get past the apple logo boot screen (the spinning disc freezes). However, I can boot into Windows (boot camp) without issues.
Also, when I pair either of the 4 GB sticks with one of my old 2 GB stock sticks the laptop boots up fine in OS X. The system profiler registers it as 6 GB of 1067 mhz RAM (the stock sticks are 1067 mhz)
So I installed osx 10.4 server on a Power Mac G4 (white/blue)
Went throught the setup screens and did a complete reformat / install. The boot disk is set to the HDD. after the install is complete it just boots to the loader screen. (Where the mac face shows, followed by a question mark) and just cycles over and over.
I can put the DVD in at this point and restart the install.. I did go in and check the disk permissions and disk status and both passed..
I've also checked the open firmware. printenv and it shows the HD and path.
I had to reinstall Snow Leopard Server on my Mac Mini Server. I did it via a firewire connection to my MBP. Everything runs fine when I boot in target disk mode from my MBP. Problem is when I disconnect the MBP and boot just mini it gives me an error message that says I need to restart the computer. I have the two 500gb drives on the mini configured in a raid array.
Info:
Mac mini, Mac OS X (10.6)
I'm not sure if this is intended behavior or not. I just installed PS3 Media Server on my Mac Pro (Snow Leopard 10.6.3) and under Navigation/Share Settings under shared folders when I click add I can only select folders on my OS/boot drive and nothing else.
I've never used this on a Mac before but when I was running it on a Windows box I could just go there and hit add and pick whatever folder I wanted on whatever volume/drive I wanted.
Is there some config/change I need to do so it can view other drives/volumes?
I have a 2 week old iMac 27", i7, 2tb Hard Drive, 16gb RM
In the second week the boot up times became very slow.
I would turn the machine on and get the chime within 5 seconds or so.
Then just a black/blank screen.
Eventually after about 10mins I would get a white screen then it would boot up normally.
Now the machine just doesn't get to the white screen. So I get the chime and then just darkness. It does sound like the machine is on (usual quiet imac whirring).
I've tried various key commands when I turn the machine on including pressing C with the install disk in the dvd drive and the alt, control, P, R pram reset.
I've also tried unplugging all the cables, leaving the machine for a minute and switching back on. I did manage to perform the PRAM reset once. I reset the machine and it booted fine.
But now when I switch it on just darkness.
I've called after sales and will try to get the machine replaced but in the meantime is there anything I could try that might make the machine work? I need to do a remix this weekend (deadline Monday) so really need to get it working.
MacBook Pro 15" (15-inch Core 2 Duo) late 2006 this apple macbook boot lion from usb or firewire ext hdd or usb stick which of 3 better must boot Lion on ext device? or none at all?
View 14 Replies View RelatedI have a MacBook 4,1 with Intel Core 2 Duo processor 4GB Ram. It is taking over 10 minutes to boot up past the gray apple screen when I turn it on. First I cleared the PRam (?) then I checked the disk using Disk Utility Verify, and it said the disk needed repairs. So I ran the disk repair and it said it was unable to fix the errors on the HD.
I did a little research and tried booting into the Single User mode, then running /sbin/fsck -fy. It said that it found errors but could not fix them. I ran it two more times as suggested and got the same result each time. I then tried rebooting and now instead of taking 10 minutes to boot up, it takes about 5 minutes on the gray apple screen and then just turns off. I started in Verbose mode to try to troubleshoot the error and it appears the last thing to come across the screen before power down is a message "Apple Yukon 2: RxRingSize <= 1024....etc".
I decided next I would run the Apple Hardware Tester. The test came back with an error code "4SNS/1/40000001:IG0C-0.265". I am very good at searching the web but I could not find any errors that had the IG0C or IGOC or any combination at the end, but plenty of 4SNS/1/40000000(1) errors with different endings. From what I can tell people are saying anything with 4SNS/1/4000000 is a logic board failure, but this computer was literally just booting this morning until I did the /sbin/fsck -fy.
Info:
MacBook, Mac OS X (10.5.6)
My mid 2010 iMac i7 will not boot past the apple logo? I'm running 10.7.3. I have tried restoring from TM backup from recovery mode (worked the last time this happened) however upon completion it returns to the recovery screen? I made a disk of Lion when I downloaded the first time (followed same instructions sourced from numerous websites) which does not seem to work when i set to start up from this disk, just gets to the grey screen and flicks between the apple logo, a folder icon with a question mark and the circle with line through? Now I can't eject the disk either, a message appears that system can't eject and to make sure all applications are closed? Not sure how to go about closing these applications without being able to start the system? When I tried booting from the Macintosh HD I got a message that the boot cache partition was faulty? I have ran disk permissions etc all ok.
Info:
iMac, Mac OS X (10.7.3)
This is bad and old, and full of lessons about backing up. Anyway, internal boot drive crashed a week ago, and internal optical drive is busted. New external LaCie dvd burner works fine, but all attempts to start up from Tiger, Leopard and Diskwarrior installation disks just end up back in OS10.3 on my external LaCie FW drive. I've tried many things: unplugged everything; switched external LaCie to USB (wouldn't boot), unplugged power from internal optical drive so Mac wouldn't look there first (somebody suggested that). Attempts to start up installers from mounted DVDs result in installer screen with restart button, which, when clicked on, results in... you guessed it... boot back to dreaded 10.3 system. Night owls and westcoasters, I am up for hours yet, pulling hair.
Information:
G5 Dual 2GHz
Mac OS X (10.4.3)
Is it possible to boot from an external Firewire DVD Drive? It certainly isnt from an external USB DVD. Real answers only please, not "I think so" ones based on HDDs or rumours you may have heard!...
Background:
I've got an MCE Optibay in my Mid-2010 i7 MBP. When installing Bootcamp it refuses to install from the external USB DVD drive. In the end I pulled the 2nd HDD out and reconnected the internal DVD. It then worked fine without a hitch. Then I reinstalled the 2nd HDD and all was fine for a few days.
Now I want to resize my Win7 partition (bigger, as MS Visual Studio's bigger than I thought, and I might stick some games on). I can shrink the OSX partition fine with Disk Utility, but windows won't grow the Win7 one because the empty space is before the Win7 partition, not after it. Apparently this can be done with GParted. Guess what? I can't boot the Linux based GParted CDROM from the external USB DVD drive! So, will a Firewire one work where USB fails, and solve my alternative OS booting issues? If I buy one I can then either use GParted, or delete the Win7 partition and start again without having to pull the laptop to bits all over again, only to put it back once I'm done, and possibly have the same issues in the future. Obviously I don't want to blow extra money getting a Firewire DVD drive though if it's a waste of money...
This is the 1st time i got a Mac , i bought a black Macbook 2.4GHz some days ago .
I installed Windows Vista Ultimate using Boot Camp , and all went smoothly .
Only 1 prob is when restarting , i have to wait too long for the Windows to log on , i think about 1min with the black screen.
And if i want to boot in Mac OS , i have to push down the D button or the Alt, it takes quite a long time too .
So do you guys have any solution to this problem ? I want to get rid of the waiting time, way too much.
And do you know how to make my Macbook jump right in the choosing section when it starts ? ( so that i dont have to push down any button when it starts )
Yesterday my screen (30" Apple Cinema) started showing symptoms of graphics card failure, jagged lines across the screen. I rebooted my Mac Pro and it was gone. Then it happened again an hour later, this time the machine didn't boot, I get the Apple logo, and then it hangs up and the screen is shifted to left (I get apple logo on left side of the monitor instead of the middle) and jagged lines all over.
So the first thing I tested was using Target Disk Mode, it works. I can access my Mac Pro's internal HD's by TDM from my MacBook Pro. Then I tested single user mode, it does boot, I can't read what's written since the screen is shifted to left, but if I type (without seeing) reboot and hit enter, it reboots. So I assume the single user mode is working.
What else can I try to 100% make sure it's my graphics card that failed and everything else is ok with Mac Pro? I already ordered a graphics card replacement but I wouldn't like to be surprised if the Mac Pro still doesn't boot when the card arrives.
P.S. It won't boot from Apple Startup DVD either. Same thing happens, gray logo then kernel panic with jagged lines all across the shifted screen.
I have OSX installed on a very old Powerbook. Well it was working and then I left it for awhile and now it is giving me the good old folder to question mark screen (maybe someone dropped it?). Well I'm not much of a mac user so I looked up all of the different boot key commands and tried to boot from my OSX CD. Holding down C did nothing, and neither did ANY of the other commands except holding down option and that key command that restarts the computer (apple, option, shift, esc?). Anyway, I got into the screen that shows your hard drive and all other devices and it actually listed the CD drive so I clicked it and clicked the next arrow. I waited for awhile and then the screen reloaded (as if it was rescanning for removable devices) and then stopped and only displayed the local disk. What is going on?! It only sometimes displays the CD in this screen and the next arrow never does anything regardless!!
I really don't know any of the computers stats but if I were to guess they're pretty bad. All I know is it used to run OSX just fine and then other people used it and now it doesn't do anything.
