OS X Mavericks :: BOOTCAMP Partition Not Visible In Finder - Not Mountable In Disk Utility
Sep 3, 2014
Did a fresh Bootcamp install of Windows 7 on my MBA running 10.9.4, switched back and forth a few times and now the BOOTCAMP partition doesn't show up in the left pane in Finder. I hopped into Disk Utility to see what was going on and it was there, just not mounted, so I clicked mount, was told it couldn't be mounted, and it suggested I run first aid on it. I clicked Verify, nothing useful to me, then Repair, and got quite a lot of feedback that I do not understand, and then after that it was still unmountable.
I tried to copy everything it said into a pastebin because it was very long with lots of starting and stopping and counting percents inbetween, but it was over 500kb and that's the limit for free users on pastebin, so here's a trimmed version. [URL] .... I tried booting into Windows after that, and it jumped into System Repair. Apparently, according to Windows, my Boot Manager is missing or corrupt... and since I still can't access it from the Mac side of things, I thought I'd just wipe the partition in BootCamp Utility and start over.
Except instead, I get this error: "Your disk could not be restored to a single partition.An error occurred while restoring the disk to a single partition."
Disk Utility let me wipe it but I still can't mount it, either, again suggesting I run first aid on it (this does nothing). I can't boot into the Mac's Recovery mode either. It just jumps straight to Internet Recovery. When I hold option upon boot, all three partitions show up (Mac, Recovery, Windows), but when I click the recovery one it loads for a bit and then the laptop just instantly shuts off.... Have I corrupted my internal harddrive perchance?
For a while now I've been really frustrated by the fact that my BootCamp drive seems to have disappeared from the desktop, and is not mountable from within Disk Utility. I am running a fresh install of OSX Snow Leopard, as well as a new BootCamp install with Windows 7.
I recently upgraded my Macbook Pro (2008 with gray keypad) which had snow leopard and was running winxp with bootcamp to mavericks and now when I try to start my winxp it begins to start but then I get the "do you want to start in safe mode" screen and when I ask to start in any of the modes winxp will begin to start with the WinXp logo showing and the blue bar moving across the the screen and then there is brief (microseconds) flash of the "Blue screen" after which the computer restarts. What can I do to get my WinXp working again?
I created a new Boot Camp partition with Windows 7 Ultimate on my MacBook Pro (i7, 2.8 Ghz, 750 GB HD) running Mavericks 10.9.5. The 2 disks were about 70 GB (Mac side) and 680 GB (Windows side). I wanted to create an extra, data partition and created it after having installed Windows. I used IPartition to do this and resized the Windows partition to about 90 GB and created an empty partition and formatted it with IPartition as Microsoft NTFS.
Now, when I boot into Windows I cannot see the empty data partition: but it's visible and mounted when I boot into Mac side.
I tried to to create new volume on empty space with Windows Disk management but got this warning and canceled that operation fearing that that would mess up the booting into Mac or Windows or both: How can I get that empty partition visible in Windows?
I just restore my Mac OS to a single partition and then I tried re-partitioning but it's giving me an error. I've tried several times, tried using different sizes every time. My HD's capacity is 250GB, and I've got 108.95GB free. So I am sure that making a new partition of 35 - 40 GB is not a big deal. I also tried using Disk Utility, both from the Mac OS install disc and while using the Mac OS itself, but it keeps giving me this error. I do not want to format my Macintosh HD's partition because I don't have an external HDD on me at the moment so I will not be able to back up. I have a lot of important data that can not be deleted.
I would like to "Back-up", "Clone" or create an "Image" or whatever else people call it of my bootcamp installation. I know I can create an "Image" of bootcamp via disk utility but how would I restore it?
Would I first delete the bootcamp partition and then re-create a bootcamp partition and then restore? Or would I just restore? Will the end result be what I am expecting, i.e., my Win 7 install right back to the perfect state of when I created the image?
Right now, let's say my Windows 7 install got smoked one day for whatever reason (it is windows...) and I needed to re-install. Me personally, I would just go into Bootcamp Assistant, delete the Windows partition then create a new one and then get installing. Unfortunately installing and updating takes hours and that is what I am trying to avoid.
This is what get when I go into Disk Utility and I want to delete the partition Macintosh 2. I see these 3 things. The "Logical Volume Group" and the 2 partitions. Where is my main hard drive? How do I get rid of the Macintosh 2.
Info: MacBook Pro with Retina display, OS X Mavericks (10.9.4)
I have a 3 TB disk that I used for video files that I now want to use for backup. So I wanted to erase and partition the drive to wipe it clean. So after going into Disk Utility and "trying" to erase and partition the drive, it now only shows the drive and no volumes.I cannot create or partition volumes. I tried verifying and repairing the disc but that didn't do anything. The only buttons available are Verify, Info and Burn. What do I do to use the drive again?
I wish to change partition scheme, sizes, in an external drive. All the partitions are MacOS extended (Journaled) and they map, according to the layout in Disk Utility, as follows: Partion 1, 2, 3,4 where 1 is at the top and 4, the bottom. I want to make partition 2 larger, so I decreased partition 1 by half. Now the layout is 1 a, 1b, 2,3,4., where 1b is now free space. Disk Utility will not allow me to increase the size of partition 2 by dragging the corner. Which of the following options (if any) will allow me to increase the size of partition 2, without erasing the data, using Disk Utility:Select partition 2 and manually writing a new value in the size box, equal to the present partition’s size plus the free space?If I delete partition 1 completely, will I then be able to increase the size of partition 2?If I delete partitions 1, 3, and 4, will I then be allowed to increase the size of partion 2?Is there another option?
(Actually, partition 3 is an eDrive, a data recovery utility created by TechTool Pro 7, so I don’t really know how it’s formatted.)
SeagateHD 1.5TB USB drive.
Info: Time Capsule 802.11n (2nd Gen), OS X Mountain Lion (10.8.2), MacBook Pro, iBook Dual USB
Having trouble with my backup drive. It's a 1TB WD My Passport Ultra.
The drive mounts in Finder, but is extremely slow. In Disk Utility, the drive shows the correct disk space usage and number of files; but in Finder it only shows the folders/files at the root level of the drive, and each has a size of zero bytes with no items:
What is happening? How can I access the data (it's obviously still there if DU shows the files) and (possibly) fix this?
Info: MacBook Air (13-inch Mid 2013), OS X Mavericks (10.9.4)
I am trying to repair my mac. But in disk utility, the hard disk is not visible to proceed. Its showing disk0 -> volume with only 1.79GB. and all the options are disabled. The capacity of my mac book pro was 500GB.
Disk Utility Crashed whilst creating a Partition, and I now have ~100GB missing, which was the amount I had allocated to the new partition.
The new partition didn't get created, and I now have 100GB missing from the Hard drive. I have a 1TB hard drive, and when I go to Disk Utility, it says: Capacity : 999.35 GB (999,345,127,424 Bytes)Available : 586.1 GB (586,103,844,864 Bytes)Used : 310.52 GB (310,524,317,696 Bytes)
Which adds up to about ~900GB.
I tried Repairing Disk in Disk Utility, booting into Recovery Mode and Repairing Disk there, but neither made a difference.
Info: MacBook Pro (15-inch Mid 2012), OS X Mavericks (10.9.3)
I installed Win 7 in bootcamp and everything was working fine. Then I started to play around with rEFIt to install Linux as a 3rd OS. I managed to install everything but since the driver support in Linux was poor, I decided to wipe out Linux + rEFIt and return to the initial setup (OSX + Win7 in bootcamp). I deleted the Linux partition and rEFIt but now, my MBP starts and I hold the option key, I can't see the Windows drive anymore. The (NTFS) partition is still there and I can access all the files from OSX but I can't boot it.
My PowerBook G4 crashed and I need data from it. I already had bought an external drive and had begun loading some fotos and music. Now I'm at a friend's Mac, firewired and all, and the external drive (visible in the disk utility) isn't to be found.
I don't want to erase and reformat, obviously, ... can I drag it onto the desktop from the disk utility?
Disks I put in the Superdrive, external hard drives, or anything in the USB or Firewire (thumbdrive, etc) -- nothing shows up on the desktop. All are visible in Disk Utility. USB thumbdrives and external hard drives are visible in the sidebar in Finder, but disks are not (only disk utility).
Because of this I can't burn a disk because the disk is not being recognized. In Disk Utility, the external hard drives appear mounted and can be opened in Finder, but why aren't they appearing on my desktop (they used to)?
First some background info. I recently purchased a 1TB hard drive for my 13" MBP, and I am about to do a clean install of OSX 10.6 and Win7 64bit on separate partitions.
And I want to setup the partitions before I install using Disk Utility. The reason for this is because I'm under the assumption that when creating a NTFS partition its better for the disk to be blank so it can put the MFT(Master file table) and MFT Mirror wherever it wants instead of some random spot on the disk (that way disk writes will be faster). The MFT thing was true when converting a FAT32 disk to NTFS. Nativity formatted NTFS disks were always faster then ones converted from FAT32, because the MFT was spread out instead of at the start of the disk.
I'm worried that installing OSX and then using the bootcamp utility will cause the MFT on my NTFS partition to end up in a un-optimal place and disk Reads/Writes will be slower.
Ok, so here's my questions.
1.) Should I be using a GUID Partition Table or Master Boot Record(Remember OSX 10.6 and Win7)?
2.) Should I use Disk Utility to Create a the OSX partition and then leave the second partition as Free Space? / Or should I use a third party utility and make the OSX partition and the NTFS partition at the same time?
3.) If I do create the partitions Manualy, will bootcamp still work correctly?
4.) Should I Use Journaled or Case-Sensitive Journaled on my OSX partition?
I know all of the questions were stupid, but there isn't any info on the web about it.
I have a 2TB Western Digital My Book Studio FW800 external that has 5 partitions, connected to my 2011 iMac. I had help doing the partitions and don't really remember the reasoning, but one is just for my SuperDuper! backup, one is Miscellaneous, one for movie clips off my camcorder, one for misc scanned photo's and one for my genealogy research. I back up using Time Machine to a Time Capsule and also to this WD hard drive with SuperDuper!
Recently I'm getting a pop up message that "Mac OS X can't repair the disk "Genealogy"'. And it needs to be reformatted. It's become a read only disk. When I look in Disk Utility it shows all the partitions as "Mac OS Extended (Journaled)" EXCEPT for the one in question. I also noticed that there are a lot of files with "date created" being the same date in 1969! These files may be letters I've written or photo's I added to that partition within the last few years.
I think I have to completely reformat the entire external hard drive to repair this, but I want to make sure. Because it's going to be a major hassle backing it all up to another external (having to get one first) and then figuring out how to make the files that have turned "read only" in that one partition, back to their original state! Does this sound right, that I have to reformat the entire external hard drive? And how do I get the read-only files back to their original state.
I had windows vista installed but suddenly the audio decided to become faulty, after spending a day trying to fix it i realized I have a windows 7 install disc so i might as well just replace vista with windows 7. I didnt take care of vista or ever register it so it became quite a task to upgrade so i just deleted the partition and went to create a new one and just do a full install of windows 7.
I made the partition but the wrong format, so i removed it through boot camp assistant and created another, except now it keeps giving me the "back up the disk and use disk utility to format it as a single Mac OS Extended (Journaled) volume. Restore your information to the disk and try using boot camp assistant again" Now, I'd love to do this, except I have no idea what I'm doing and WHY this error has occured. After becoming frustrated I switched from my imac to my macbook pro and received the same error when trying to create a partition. So any help on exactly what I need to do would be a HUGE help. I only use windows for music production (I know, seems backwards, but I use Sony Acid and FL Studio so I'm stuck with Windows)
Anyone knows why my external HD (USB disk connected to Airport extreme) does not show up in disk utility? (It sits on my desktop just fine and is fully functional) I' want to erase a partition but now i don't know how.
I have run the Disk Utility verify function against my system partition. It tells me there are minor issues that need fixing up and I should run the repair disk function, by booting using Command-R and using the Disk Utility to repair the drive.Problem is, when I boot using Command-R and select Disk Utility the partition is shown greyed out and the Verify and Repair options do not work.I think this could be because the partition is encrypted. The utility does not offer me the chance to unlock the partition with my passphrase.How can I repair the filesystem errors on this partition?
My new 2010 hexacore Mac will have 24G memory, an OWC Extreme Pro 120G SSD (positioned in the lower optical bay) and four 2TB WD RE4 drives. I'll use my old Synology 209 NAS (two 1TB WD Green Raid 1 drives) for TM backups over 1000Mbps Ethernet. Yes, I'll need to upgrade to a larger NAS very soon. This will be my first Mac Pro (have MBPs and iMac) and will be used for web design and development (mostly Adobe CS5 products).
The SSD will be used for boot and application files. I plan to use Disk Utility to create a 1+0 Raid array for data files. For a Scratch disk, should I: 1) create a partition on the 1+0 Raid Array for Scratch 2) partition a chunk of the SSD for Scratch 3) attach a spare external 2.5" WD drive via Firewire 800 for Scratch
Based on my reading, it seems that option 1 makes the most sense but I'm not entirely sure if you can partition a 1+0 array with Disk Utility. I'm pretty sure option 3 is quite silly but wanted to toss out the idea. Lastly, are there any generic recommendations on scratch volume sizing?
I have a 640GB external USB hard drive that I use for time machine currently. I would like to go in and add a partition to load movies to and plug it into my PS3. Can I use disk utility to create a new partition without erasing the stuff already on the disk?
And then is it possible to format a partition larger than 32GB as FAT?
I have used bootcamp to partition my disk and install windows vista onto my uMB. Now I want to partition the disk again to create a tri boot setup where I can either install ubuntu or the dev preview of snow leopard (I haven't decided yet). Can I just do this with disk utility and shrink my OS X partition in order to create a new partition or will this cause problems with the disk? I would really like to not do a fresh install of OS X because I have had to do this twice to fix disk problems relating to bootcamp.
I own an iMac with a 250 GB HDD along with a Macbook that originally had a 120 GB HDD. So when I purchased my 1 TB external HDD this summer, I partitioned the external so I could back up both my iMac and Macbook via Time Machine. Seeing how small the Macbook HDD was, I allocated roughly 300 GB of my external to it, with the iMac getting the rest.
Originally I had 2 partitions on the internal 500gb hd in my MBP, one was 455gb the other was 10gb that I used to mess around on. I do not remember what format the small partition was in last, it may have been FAT32. I wanted to delete the small partition and consolidate into one partition. My OSX partition is formatted macos extended. I went to Disk Utility and deleted the small partition by selecting it and clicking "-." There was grey space where the partition used to be. No problems here. Most of the options in Disk Utility are greyed-out.
I cannot select a different partition scheme. When I try to resize the partition either by dragging it to cover the grey space or by manually typing in a larger size, there is no way to apply the changes. The "Apply" button is continually greyed-out (See Image). If I try to resize the partition and then close the window, Disk Utility alerts me that I have an operation in progress and that unsaved changes will be lost. Disk Utility is not letting me resize my main OSX Partition, it appears that I do not have appropriate permissions to make this change - I am the only user/admin of this machine.
I having trouble resizing an external harddrive of mine. It is a 500gb Lacie drive, and inside it has two partitions: time machine (250gb) and my stuff (250gb). I want to make time machine 150gb and make My Stuff occupy the remaining space. However, when I enter Disk utility, there is no dot between the partitions that I can drag. When I pull the corner, the disk gets smaller, but after resizing there is still a blue rectangle outlining where the old disk was. The partition "time machine" is used for time machine backups, but I have deactivated backups in Preferences, and Time Machine is currently "off". I have included an image for clarification. How can I resize the partitions the way I want them?
i am trying to format a brand new 120 GB hard drive via an external USB 2.0 enclosure. About 25 minutes ago, I selected the "erase" option and slected the Mac OS Extended (Journal) Volume format. For the last 25 minutes, disk utility has been saying that it's creating a partition map. It's doing nothing.
I have reason to believe my enclosure may be faulty. (I had a similar problem on an old hard disk and thought that the problem was with the disk; now I know.) I need to know: How do I disconnect/eject the hard disk without damaging it? The eject option in Disk Utility is grayed out. If I attempt to quit Disk Utility I get a warning telling me I could leave my disk inoperable.
