I am getting a 2008 Mac Pro and i am trying to get a Solid state drive for it i have two questions.
What is the connector type on a mac pro from 2008 Sata or Sata II
Also would i really notice a big performance increase in getting a SSD for my OS and programs?
I've ever tried to upgrade a hard drive on a 13", 2007, white Intel MacBook.I was following the directions I had found on the internet.I've taken the old drive out, swapped the hard drive plate from the original drive to the new hard drive and tried to push it back into the same slot, but for some reason I can't get it to go all the way back into that slot the drive fits in.Strange enough, it also feels like it's pushing against something rubbery on the inside.It's less than a 1/4 inch from going all the way back in.I've made certain that all the screws are tightened all the way on the drive, but can't figure out why I'm getting resistence when I try to push it in that weeee little bit.I am certain that I have the drive flipped the proper way too, because I took note of how the original drive was oriented and made sure I duplicated that on this new drive.Like I had said before, it feels like there is something rubbery that's in the way, I just can't get to it.So I'm also curious if anyone knows if I were to take off the top cover on the laptop whether that would expose the hard drive so that I could see why it's not fitting into the connector properly.
Info:
MacBook, Mac OS X (10.5.8)
I have a spare DVD drive and decided to install it in my Mac Pro.
When I opened up my case I found there was a standard Molex power cable, but the existing DVD drive in there had the above adaptor, with one spare to attach another drive with.
My spare drive has space for SATA cables, that's about it.
Any ideas what adaptor this is?
I just purchased an ICY DOCK for use with an Intel SSD. I already a have one of these, however the new one seems to have some new revisions. Basically this new one allows me to completely take off the cover. The old one slides forward and up, but the cover does not disconnect. The old one also, when closing, makes sure the SSD is seated correctly into the connector port on the ICY DOCK. The new one does not seem to have this "automatic" feature where when I close it.
View 3 Replies View RelatedToday I went to plug in my Lacie 250 GB USB external hard drive into my 13 in. MacBook to get a shirt template for a design I am making. I discovered that the hard drive just would not mount and show on the desktop, and I remembered that this happened a few days before, but all I did was unplug it and plug it back in, and it worked... except that today, that didn't work at all. I tried the other USB port, and the hard drive showed up on the desktop for about a second, and then disappeared. I kept on replugging it back into both USB ports, but nothing happened.
Then I tried to see if it would work on the PC beside me, and it was recognized as an external device; however, a message came up telling me the drive was malfunctioning. I am guessing this is from ejecting it incorrectly (because I am in a hurry to head to my next classes...I use this laptop at school), but I have incorrectly disconnected it before in the past and this problem never happened to me before.
Every single project I have ever created for my design career is on that hard drive, and all I want now is to get my files back. All I need it to do is show up on the desktop for just the right amount of time for me to copy my files onto my computer.
I read online to put it into the freezer for a while and it should mount, but that didn't work. I tried using Disk Warrior, Data Rescue 3, and Tech Tool Deluxe, but the hard drive did not show up on any of those apps.I tried plugging the hard drive into an iMac as well, but it did not show up either.
Got a new MBP last month to replace my white MacBook - loving it as an upgrade but one gripe - if I'm sat using it on my knee I regularly hear the "click" type noise of what I imagine is the protection of the hard drive because it thinks it is being dropped.
I never heard this on my old Mac and while it's not a huge issue it is a bit disconcerting, as though I'm being told off for moving it in a fairly responsible way.
My PowerBook G4 (Alum) died. I've had it for 4 years, taken it with me to Alaska and all over the lower 48, and have had nothing but happy experiences. I knew she was gonna go, but I was hoping she'd hold on until I could afford a MacBook. Alas, no. The problem appears to be the ability of the logic board to communicate with the hard drive. I can hear the HD spin, but even with Disk Warrior, I cannot locate it. The Mac Geniuses at my local Apple store confirmed this and gave me a shoulder to cry on. I've run Disk Warrior, Disk Utility, and tried finding it using the target disk mode - no luck.
The problem is that I've got 4 years of teaching materials, 6000 songs, and irreplaceable pictures on the HD, so I can't bring myself to just trash it. It's true that you only fail to back up you stuff once. This is my once. I've heard that with PC hard drives, you can just drop the old HD into a USB HD box and use it as an external HD. I can't afford professional data retrevial, and I want to give this option a try if it'll work with a Mac HD. Any ideas or suggestions?
How do i play media files from my external hard drive without transferring the files to my mac hard drive? I have a lot of media files and want to be able to play them soley from my external hard drive.Â
Info:
iMac (27-inch Mid 2011), iOS 5.1.1
My PM G5's Hard Drive has been making wierd noises lately and I'm really beginning to worry that it's failing. How can I be sure?
View 1 Replies View RelatedI have an aluminum unibody macbook from October 2008. I'm looking to upgrade the 160 GB hard drive inside to a 500 GB one I'm considering from Newegg. Would it be possible to migrate/copy/clone the entire contents of my current hard drive to the 500 GB one? I also have a section of my current hard drive partitioned for Bootcamp. Would this affect my ability to transfer everything over?
If this is possible at all, how can I go about doing so? If there are steps laid out somewhere, I'd appreciate a referral. Sorry if my question is a little elementary, but I did a search on these forums and also google and nothing really came up
I know this is going to be an incredibly easy fix, but I can't find it. The Hard Drive on my new iMac is not appearing on my desktop, nor is it appearing in the "Device" menu in Finder.
if i delete files off my internal hard drive (Macintosh HD), will it still be on my external hard drive or will it just add to it?
View 1 Replies View RelatedI have just installed a new hard drive in my imac intel 20" (2006) and upgraded the memory and now the hard drive does not show up in the 'select destinations' folder of the install program. I can see the hard drive in the disk utilities window however it wont let me do anything.It is a seagate 1TB SATA II drive however it is displaying it as a 7.3 TB.I have tried to erase and partition and get the same error message each time, 'Input/Output error'.
I have tried starting the thing with the install disk which is Mac OS X (Tiger?) which came with the computer
Info:
iMac
with cloning/copying the content one an external hard drive onto a new external hard drive. Basically, I have a 500GB FW400 drive which I use to store my media files. It's full, so I purchased a 1TB FW800 drive to replace it. Obviously, I thought I could simply copy and paste the media files from the old drive to the new one.I cannot copy the media files to my internal drive first as my internal drive is only 250GB and nearly full itself.I have used Disk Utility to attempt to close the old drive to the new drive, but keep getting "insufficient space" errors.
View 9 Replies View RelatedRecently I bought 2 identical WD Scorpio Blue 1TB hard drives for my macbook pro 13 inch 2010. My aim is to replace the internal hard drive with one of the two I just purchased and use it as my system drive with Lion, Windows and Data partitions. And for the other hard drive I want to use it as a full disk back up for the internal drive (now 1TB hard drive). After I was done with setting up both windows and mac and data transfer, when I booedt into the recovery partition from the internal drive to clone the drive to the external drive, the disk utility gave me this error (Could not validate source - error 254). I also tried using Carbon Copy Cloner but it only could clone partitions, not the entire drive. Yesterday I downloaded a copy of Clonezilla. It worked fine until it had to clone an exFAT partition (my data partition). The exFAT partition appeared as 'RAW' partition in clonezilla. As a result, the whole partition appeared to be full and clonezilla had to copy every single blocks of data in that partition and the estimated time remaining was about 30 hours. So clonezilla is out too. Just want to ask if there is any program/application (bootable or not) which allows can do a full disk clone to an external hard drive.
View 1 Replies View RelatedMacbook Pro 17" Early 2011Â
Notes. Failed HDD ASD Test.  A new hard drive was installed in September of 2011 after the previous hard drive failed. Having worked well until now the system seems to give the same problems as it had previously. I am wondering if this is a compatibility issue as others have pointed out. Â
I have been told by the technician my only option is to replace the entire hard drive again for the second time with a new one. However to my understanding a ASD test is very specific and this my not be necessary? Further I am attempting a final backup just in case. I don't have to take it in where I could just back it up myself without the system shutting down.
Info:
Mac Pro
Had a hard drive failing/failure. I am having my bad hard drive replaced with a bigger hard drive. (New Obviously) I have an iMac. (1.83GHz Intel Core 2 Duo 17-inch) To have my data transferred from the old drive will cost over a hundred bucks more. I am trying to save money but transferring it myself. All im looking to transfer is my photos. I did not have an external drive but i WILL purchse one now. My question, (to save some money) is how would i transfer my old pictures from my old drive, too my new installed hard drive. Can i use USB? Firewire?
View 2 Replies View RelatedI've just got a new external HD, but it's not being recognised by Mac OS X (10.5.7). I assumed it was because it was in a Windows format, so booted Windows, but it then turned out it wasn't formatted at all. What is the easiest way to make this an HFS+ (the Mac OS extended format), and how do I do it as I can't see it anywhere on the Mac (including Disk Utility)?
View 6 Replies View RelatedI'm replacing my old 120gig hard drive with a new 320gig hard driveWhen Ive got the new hard drive installed can I just put the old hard drive in a enclosure kit/caddy and copy my music/movies/etc across to the new hard drive?Or do I have to copy the data off before I remove the old hard drive?
View 3 Replies View Relatedi just installed a new 2nd, (750 gb) hard drive into my g5 because my first 250gb is nearly full. I'm trying to launch logic but the file is way to big. It wont let me install this program from my new, second hard drive because the message i get is that it supposed to launch from the primary or running hard drive. Can anyone tell me how i can make my second hard drive my new primary hard drive? I got the .dmg for my leapord osx. but not the originals anymore. can anybody help me with this. i'm pretty sure it's simple, i just don't know how to do this.
View 5 Replies View RelatedWhats the difference between a PATA hard drive and an ATA hard drive?
I bought one of ebay for my 15" Powerbook, i got it today, and it doesn't work lol. But the post clearly says, will work with all ibook's, and Powerbooks, So im not sure if it's the right kind of drive. The HD i ordered is on route for a replacement, so hopefully it was just a defective drive.
I've had a lot of problems with my iMac G5 power supply and since I have newer computers I've decided to get rid of this computer.Â
I want to save the hard drive and put it in a case, then use it as an external drive on my other Macs.Â
What sort of case do I need to shop for? Should I look for SATA or what exactly is the proper nomenclature.Â
Is USB 2 the preferred choice, or Firewire, or what? Is there a USB 3? I use a mid-2010 27 inch iMac with the intel processor, and I needed to buy an adapter to use my older Firewire external drive. Is Firewire a dodo?Â
Transfer information from one hard drive to another hard drive
Info:
PowerMac, Mac OS X (10.5.8), G5 dual 2.0 processors
I need to back up hard drive to an external hard drive. How can I do this automactically?Â
Powermac g5
10.4.11
tiger
Info:
Mac OS X (10.4.11)
I bought a new 500GB WD hard drive for my Late 2008 MacBook to upgrade from my 250GB drive. I have a hard drive enclosure, but I was wondering if when I install my 500GB hard drive, would I be able to use the enclosure to transfer files from my 250GB drive? I hope this was specific enough to get a clear response. If not, I'll try re-wording my question.
View 7 Replies View RelatedHow do I transfer all data from my old internal hard drive to a new internal hard drive? I have an iMac with a 320gb internal HD that is full and I am replacing it with a 2tb internal drive. I have several external drives; 1 tb, 2tb and 3 tb. The 2 tb is being used for Time Machine. Do I have to buy an enclosure? If so, where would I get an inexpensive one? I also want to partition the new internal drive for Windows, and I'm not sure how much space to use for that. I plan to use Windows to check my work in PowerPoint created on my Mac for clients on PCs.
Info:
iPod shuffle, Mac OS X (10.7.3)
I have a Imac 20 with a small 3.5 hard drive and I have bought a bigger 360 gig 3.5 hard drive to replace the old one. I have the new one in an external case with USB 2.0 right now. Is there some way I can transfer the entire contents of the old hard drive on to the new one and then swap out the old drive with the new drive and not miss a beat?
View 6 Replies View RelatedI have to hard drives in my powermac. And I am running out of space with the one that has the OS on it.
I want to make the 2 internal hard drives i have appear as one so i can still install and use things that say "must have mac OS installed on this drive to use" or whatever.
i've heard of people using RAID to join them, but i want details on how i could do this.
I have an iMac G4 with a failed HD. I know this because it boots from my external drive. Does anyone know where I can find the Hard drive part # and a take-apart guide?
View 3 Replies View RelatedI know it doesn't have a lot to do with Apple specifically but it is hardware and there was nowhere else suitable.
I bought a record player over ebay and the only thing missing is the power cable. It is an AC input and the connector looks like this.
