I can no longer burn DVD's on my PowerPC G5 with 10.5.8, but can no longer do it as well on my Macbook Pro with OS 10.6--are all internal Superdrives now non functioning!!?? I've wasted many DVD's and no successes, just error messages and failures to burn.
Info:
PowerMac, Mac OS X (10.5.8), PowerPC Processor
I Have a MacbookPro OSX 10.6.2 2gz intel core duo, recently i extracted a dvd burner from a crapped out dell laptop, it was the exact dimensions and looked identical to the old mac cd burner, so I installed it in my mac, and now my mac cant see the burner, When I go to "About this Mac" in the apple icon and click on disc burning it says "no disc burning device found". I wonder if theres a driver of some sort or do I have to re-install osx to get this working?
View 6 Replies View RelatedI already have an External enclosure that turned an old HDD into an external HDD (IDE to USB and a Power cable). Now, if i had an Internal DVD burner, can i plug it into my HDD enclosure and use it to burn DVDs?
I know it wont fit INSIDE the enclosure but luckily the enclosure has a back panel with all the hookups that come off completely so i could just plug it in and sit it on a desk while its in use.
Been trying to find an internal blu-ray burner drive to install on my 24 inch iMac 2.4. Does anyone know of an internal drive I can use.
Info:
iMac, Mac OS X (10.7.3)
When using toast, I get this error message -
The drive reported an error:
Sense Key = HARDWARE ERROR
Sense Code = 0x44, 0xD9
Iinternal Target Failure
I also get a similar message when trying to burn through the OS.
Is there a cheap way/compatible way to record audio to an external CD burner rather than the internal drive?
View 3 Replies View RelatediMacrunning OS10.7.3 have been burning DVD sucsessfully Using Toast 11, but now receive error message Sense Key = Medium error sense Code 0x02 No seek complete. Tried different blank DVD's same error. What does the Code mean?
Info:
iMac, Mac OS X (10.7.3)
My internal hdd isn't detected anymore while booting.  What happened: after plugging in an USB-printer my macbook freezed immediately and I had to shut down by pressing 5 seconds on power button. I pressed power on button and my internal hdd isn't detected anymore while booting (question mark is blinking).
After replacement by a new ssd and booting via USB the new ssd isn't detected, too.Is the internal SATA3 cable broken or is it a defect of some kind of SATA3 controller assemled on mainboard?Â
Info:
MacBook Pro, OS X Mavericks (10.9.3), Mid 2012
I want to keep my applications etc on one internal HD and use my second internal HD as a back up.I am a graphic designer, and i have been backing up to an external LACIE Porche 160 Gig firewire HD. This has worked fine, but...My second internal HD (112 gig?) is still loaded with 10.3 and has adobe CS2 on it along with some other crap that I no longer need.I have loaded Adobe CS3 on my primary drive and have all the files I need on that one...What is the best way to set up my second HD as a "slave" drive to improve the performance of my G5 dual 2 Ghz??Will there be any issues now that I loaded Leopard on the primary HD?
Information:
Power PC G5 Tower 2 Ghz dual processor (2004?) with two internal hard drives
Mac OS X (10.5)
how to install a Samsung SH-S183 sata burner?
Information:
Dual 2.0
Mac OS X (10.4.10)
I've been having problems burning audio CD's lately. I have burned hundreds in the past successfully. No problems burning data discs onto DVD's however. Last time I tried to burn an audio CD error "laser not hot enough and bad media" have both come up. Some audio CD's that do burn successfully have skips throughout them or a static noise in some cases. This problem first happened when I bought a 100 pack of Sony's and chalked it up to a bad batch and then I bought another 50 pack of Sony's ( a brand I have had a lot of success with in the past) and am getting the same issues. The CD burner has seen a lot of use but should that matter?
Is the HD fragmented? My CD burner laser cover need cleaning?
Information:
G5 dual 1.8
Mac OS X (10.4.11)
iPod 80GB
After a DVD burner for the second bay of my Dual 1.25 that will work out of the box...
I was hoping you could recommend me a Blu-Ray burner for my new Mac Pro.
From what I've found, these are the top 2 choices:
http://www.mcetech.com/blu-ray/
and
(URL)
The second one is external - I prefer internal that I can drop into the Mac Pro. But it does have LightScribe - nice! Maybe there's something out there that is internal AND has LightScribe? Who here has installed a blu-ray burner into their Mac Pro?
Anyone have a BD Burner that they use on their Mac Books or Mac Book Pro? I am interested in getting one to backup my images, I am a photographer and shoot in the RAW format. I also just purchased a new camera, where the uncompressed images are anywhere from 20-30MB a photo. So projects tend to be quite large.
View 9 Replies View Relatedif i wanted to get a blu-ray reader/ burner for my mac pro i will need drivers for it. Makes sense. Here is the issue all the blu-ray drives i see that are supposedly for mac do not seem to come with drivers.
I have also seen people say all you need is a software such as toast titanium for Blu-Ray.
I want to put blu-ray movies on my mac and convert them to HD so i can stream them. so i need a blu-rayu drive.
I recently purchased this BR burner: (URL)
I mounted it in this external enclosure: (URL)
This is all running on a 27" iMac Core i7 via firewire, and daisy chained off my GuardianMax RAID drive.
This combo works great for ripping and playing, however, i do have one problem. When the player is on and i need to either reboot or shut down the system just hangs. It won't proceed until i power down the bluray burner.
i recently updated to mac 10.3.9 and my cd burner won't work anymore. under system software is says disc burning is not supported with my iomega CDRW86522EXT3-B: how can this be? earlier in the year it worked fine, and I did burn discs. What happens now is that sometimes it says that my disc isn't supported, and if I do get throught the burning nothing plays on my regular compact disc players. (I'm burning audio files)
View 3 Replies View Relatedtried 2 boot up my G4, nothing, replaced internal battery, no status change, advice? would still like to be able to use it if possible and affordable
Info:
G4 dual os boot, Mac OS X (10.4.11), will also boot up in OS 9.2.2 when
I'm hoping this can be answered with a simple "yup" so here it goes.
I have an 8-core 2008 Mac Pro tower. I need to throw a blu-ray burner in it.
The tower only has IDE interface cables for the two optical drive bays.
Will these play nicely together?
I have Mac OS X 10.4.11. with an internal Pioneer DVR-106D CD/DVD burner. I "capture" opera performances on-line, edit them with CD Spin Doctor 2, send it to Toast where it is then burned to disc. I have been doing this for years with no problems. This past week I started receiving the following message "sense key=medium error. Sense code= OX73, OX03". I tried several different CDs and had three different brands which always did work but stopped working...Philips CD-R, TDK, Memorex Black CD-R. I had two Maxell CD-Rs and they worked. I purchased a cleaning disc hoping that cleaning the lens would correct the problem. Still none of the previously mentioned CD-Rs would work and I was unable to purchase additional Maxell discs locally. At Sam's Club I purchased Verbatim CD-R, placed one in the computer.....and it worked. For almost a week I've been able to burn CDs once more, until tonight. Again, I used the cleaner disc plus retried some of the other brands of CD with the same results...no burn. When I tried burning a disc with iTunes, I received the following message "The attempt to burn a disc failed. The device failed to calibate the laser power level for this media."
View 7 Replies View RelatedI received a semi working powerMac G4 Cube from a freecycle community, and while initially it worked fine, I had to dissemble the unit to replace the dvd drive which had a dvd stuck in it. I used one from a second unit that I was also given and I think the dvd is also bad , as placing the 'software installer', which I presume is OS9, causes dvd unit to make what sounds like spinning noise ( Does not sound to me like its reading anything ), and then after a few seconds it spits it right back out, and this happens everytime.Before I dissembled the unit, the cube at least booted into OS9 just fine, yet I am sure I put everything back properly. I might have chosen a bad setting in system perferences I suppose, and if so is there a fix short of getting a new dvd unit so I can reinstall OS 9 ? Also, I did try 'control' while startup, and it takes me to a very odd screen, with a icon for 'reload' ( browser icon similarity ) , or what looks like a right arrow. Choosing either does nothing, short of showing what looks like a watch moving in circular fashion.
Info:
PowerMac, Mac OS 9.0.x
My computer is Mac Pro, 2 x 2.8 GHz Quad-Core Intel Xeon, 4GB 800 MHz DDR2 FB-DIMM, running Mac OSX Version 10.5.6. I am a big time user of search (or spotlight) on my Macintosh and I have been using for years and through all the updates. I loved the recent updates to spotlight and I was able to search not only my HD but also the network drives where all of our files are located on an Mac Server.
I am the IT person of this small graphic design firm and everyone in our office work on files that are located on a Mac Server. We only keep the applications on our own client computers. Spotlight or (search) was function perfectly up to a few weeks ago but recently when I need to search something on our Signage A, Signage B, Signage C or Print A, Print B or Print C, drives where we keep our files. The search does not bring no result. This is a problem not only with my computer but there are a few computers in the office with the same problem.
What can I do to resolve this problem and be able to search again on my network drives where I keep all the files we are working on. If this function is no longer available with spotlight or search box of the finder window. Is there another software we can use to search for files and folders on our server. Since there are a few people working on the same files sometimes when the files are moved it makes it difficult for the next person to find them, in that kind of situation search was working wonderfully and I need for that to work again.
It used to work with Snow leopard.. but now it crashes on login any ideas??? i first thought it is afloat (plug suite) but i disabled it...(and unistalled) I Think the "the tube" Update messed skype up but... maybe you know it better
Code:
Process: Skype [2732]
Path: /Applications/Skype.app/Contents/MacOS/Skype
Identifier: com.skype.skype
Version: 2.8.0.659 (2.8.0.659)
Code Type: X86 (Native)
Parent Process: launchd [685]
Date/Time: 2009-09-14 09:09:35.319 +0200
OS Version: Mac OS X 10.6 (10A432)
Report Version: 6...........................
a few days ago i had a system problem so i did a clean install. Everything seemed to come back ok but now i can't get Quicktime to work anymore. All my movie files get -1856 error messages. I even tried to re-install Quicktime but every version i try wont work. I am running osx 10.4.
View 1 Replies View RelatedI have OS X 10.9.4.Â
For a couple of weeks now, when I click on any of my tags, nothing shows up; but my files seem to still have their tag when I go to "my documents". It is the same thing when I click on "all my files": the window is empty.
Info:
MacBook Air (13-inch Mid 2013)
It used to work for me when i press a combination of Ctrl+F2 to activate the menu bar, now it doesn't work anymore, even if i try a further key: Fn+Ctrl+F2.
View 2 Replies View RelatedSince 2 days ICQ doesn't work together with iChat anymore. All I get is the prompt for entering the password. Password is correct and ICQ still works with Adium or ICQ2GO. iChat probably stopped working after I installed the latest security patch for MacOS Leopard.
Deleting the ICQ account in iChat and adding it again doesn't work. Neither does deleting the AIM.plist or changing the server to [URL] like it was suggested at the Apple discussion board.
Yesterday I swapped the stock cooler of my radeon HD3870 for a zalman vf1000. Since then, the GC doesn't work anymore (even with the stock fan back). So after a night of check, test and prettty much everything, I'm pretty sure my GC is dead. What I want to know it could be a short circuit? I'm a good mac user and I already did that on others cards (X1900 with an accelero for example.) I talked with xlryourmac and he can't see. I really want to find out a plausible explanation, because I'll probably buy another GC et wouldn't want to do the same mistake twice. I have a Macpro clovertown 2x3 Ghz - 12Gb Ram- Raptor Boot- Raid 3To- Multibridge Pro 2.
View 11 Replies View RelatedI'd like to empty my trash, but it doesn't work anymore. The trash icon in my dock indicates that there are files in it, but when I click on it the Trash window appears, but the files don't show. The indicator at the bottom right just keeps on animating - it never stops, not even after several hours. furthermore, the "Empty Trash" option in the Finder menu is grayed out. The "Empty Trash" option in the trash icon's right-click menu is not grayed out. However, when I click it, a dialog appears for confirmation; I click on "Empty Trash" and nothing happens. When I list the files in my trash using the terminal (with the "ls" command), the files do show (and there is a considerable number of files). When I try to remove them, using the "rm" command, nothing happens; when I list the files again, they are still there. What must I do to get this mess fixed?
View 2 Replies View RelatedIt worked fine for a couple of hours, now it won't even load anymore. Can't delete the application from my hard drive because it says I don't have permission. Fixed the permissions but it still won't delete. Tried downloading it and re-installing and it still doesn't work.
View 5 Replies View Related