OS X :: 10.5.3 Update Half Installed Now G4 Not Booting

Jan 9, 2009

I've been successfully running Leopard on 2 different drives on the following computer
G-4 (digital audio) 733 {model before Quicksilver}
upgraded to 1.47 GHZ....processor. 1 gig of memory

Computer has been handling Leopard fine up to now. I was updating one of the drives to 10.5.3 when the screen activity locked up. After quite a long time and ceasing of drive crunching data....I did a hard restart. Since this time, the drive wont start up,. just the spooling rotor underneath the apple on the gray screen, which doesn't stop. There is no time-machine backup on this drive. I've used the Leopard install disc to run the disc utility and repair permissions but this is a case of an update, half installed. Of course, with Leopard, booting with the install disc does not show the drive, disc image on the desktop...so access for re-running the update isn't there.

View 2 Replies


ADVERTISEMENT

Intel Mac :: Turns On, Gets Half Way Through Booting Up, Then Just Stops?

Jun 30, 2012

my imac turns on, gets half way through booting up, then just stops.

View 1 Replies View Related

Mac Pro :: AHCI Drivers Installed And Still Not Booting Into Win7

Nov 5, 2009

I am not using any raid at all on my 2008 mac pro. All I want to do is achieve using SATA drives via the ODD ports on my logic board to boot windows. I know it can be done. In case you don't believe me, here is the PROOF that shows I have installed the AHCI drivers successfully in windows: Under IDE ATA/ATAPI controllers, the following exists:
Intel(R) 631xESB6321ESB/3100 Chipset Serial ATA Storage Controller, and underneath that says the following:
Intel(R) ESB2 SATA AHCI Controller.

That said, the matrix control console identifies all my 6 ports correctly. But when I go and hook up my SATA bootcamp hard drive to the ODD_SATA Port on my board, it doesn't boot! Why?? I went through all that trouble to install AHCI drivers in bootcamp annd it doesn't boot up at all? Yes, I would like to boot windows via ODD_Ports, but each time I do this it doesn't seem to boot. I am afraid to use a SATA optical drive, as the same thing will happen again. However, it appears that when I am in bootcamp, all my drives are recognized and working.

What do I need to do to get the ODD_SATA ports to recognize the AHCI during boot up(not while in Bootcamp)? I don't understand why it won't boot, after installing the matrix storage drivers for AHCI? I am leaving you with my skype id so you can chat with me on what to do here. Psychomacuser343 is my skype, while nadav333 is my AIM. As I said, I have tried everything, and while the ODD_SATA ports boot on the mac side, Even with the AHCI drivers in bootcamp, can't get bootcamp booted unless I remove it from the ODD_SATA port. Also, I managed to install one sata cable and not needing to mod my case fan.

View 24 Replies View Related

MacBook Pro :: Bootcamp Chopped Hard Disk In Half And I Can't Find Other Half

Jun 26, 2009

Macbook pro 15"

I was trying to install windows on my pro, and i had bootcamp chop the hard disk in half, but then my disk drive didnt read the cd so i had to download and install some file. and after i restarted i could no longer access the windows side, it just disappeared.....plus i cannot reset my hard disk, cant erase it, and i cant reinstall OS X because there is no memory left..

View 5 Replies View Related

Intel Mac :: Left Half Of The Screen Would Flick And Become Darker Than The Lower Half?

Jun 21, 2012

At the beginning of last year I bought a 3.2GHz 27" iMac. About a month ago I noticed that, within about 5 minutes of starting my computer back up from sleep the left half of the screen would flick and become darker than the lower half (about 4 clicks of the light button lower). Sometimes the screen will flick to become even darker than this (but usually it returns to the 4 clicks darker after a short while), and sometimes it returns to normal only to go darker again.

Info:
iMac (27-inch Mid 2010), Mac OS X (10.7.3)

View 2 Replies View Related

MacBook Pro :: Bottom Half Of My Screen Go Black And Most Of The Top Half Flicker?

Jun 23, 2010

I have a MacBook Pro with the 9600gt in it. Since updating to 10.6.4 this morning 2 times while playing java games i've had the bottom half of my screen go black and most of the top half flicker. I've had to hold in the power button and reset both times. The second time I closed the screen and reopened it, the screen was black but no mouse and nothing moved.

Any advice? Would this be something to do with my graphics card or possibly some error in 10.6.4?Edit:: This is software related to 10.6.4 update and only happens when I open up a java game in a browser.

View 1 Replies View Related

IMac :: Screen Is Half Light/half Dark - How To Fix It

Oct 31, 2008

I started up iTunes, checked my email, and looked up to see the top half of my display drop about 15 shades darker than the bottom half! I called Apple Care who told me they had never heard of something like this before and advised me to call the nearest Apple Store. I did, and like Apple Care, they had never heard of this happening.

View 16 Replies View Related

OS X :: MacBook Not Booting After Software Update

Jun 30, 2007

I have an Intel MacBook and just did a software update, one of which was a 49MB download for Intel Macs. After installing, it asked for a reboot. Thereafter it booted as far as a blue screen and then stalled. I held down the off button until it went off, restarted and it got no further. I left it for over half an hour to see if it would get past the blue screen, but it didn't. After a few minutes of blue screen, the fans ramp up. I'm completely lost with Macs and don't even know where to begin.

View 2 Replies View Related

MacBook Pro :: EFI Firmware Update 2.5 & Booting OS 10.6.x?

Apr 23, 2012

Are there any known compatibiity issues with booting from an OS 10.6.x drive after installing EFI Firmware Update 2.5?I am running Lion (10.7.3) on my MacBook Pro (13-inch, Mid-2010) but have held off installing the firmware update because being able to boot from a 10.6.x backup drive is more important right now than internet-based Lion recovery. If there's no issue booting 10.6.x (and running apps), then I will go ahead and install the firmware update, otherwise I'll wait awhile longer.

Info:
MacBook Pro (13-inch Mid 2010), Mac OS X (10.7.3)

View 2 Replies View Related

OS X :: MacBook Not Booting After Security Update Failed

Apr 19, 2009

While trying to download the latest security update I received a message telling me the update failed and it had been sent to the trash. The trash was empty and I now didn't have enough free disk space to retry the download so I decided to reboot my computer to free up some disk space. I haven't been able to reboot it since. While booting it gets stuck on the 'starting mac os' screen. I've reset the pram and I've done disk and permission repairs and have tried to start it in safe mode, but it won't. While holding the shift key to get to safe mode It still gets stuck on the same screen (though it takes a few more minutes to get there). I don't have the right version of the start up disk as apple replaced my computer but didn't give me a new start up disk.

View 1 Replies View Related

MacBook Pro :: Not Booting After Software Update Failure

Apr 25, 2010

I wanted to reformat my mbp. In doing this, I used the 'erase and install' method in my leopard restore disk then installed bundled applications dvd that was included with it. I then installed/upgraded to snow leopard then used software update to download the updates. Before this, there seemed nothing wrong with my mbp. After downloading all the available updates (~990mb), it asked for a restart to which i agreed . i watched it while it was installing the updates but for some reason before it was able to end, stated that an error occurred thus it restarted. Now i get stuck with the startup screen (the one with the apple logo in the middle with a rotating circle of lines just below it). It wouldn't stop so i hard reseted it but to no avail, still stuck with the startup screen.

View 6 Replies View Related

V10.6 Snow Leopard :: Update "Mac OS X Update Combined" Can't Be Installed

Mar 14, 2012

Update could not be expanded, and may have been corrupted during downloading. Does anybody know how this can be fixed, since the error message appears every time I try the update. Other updates run smoothly.

Info:iMac, Mac OS X (10.6.7)

View 7 Replies View Related

MacBook Pro :: Stuck In Sleep Mode After Update Now Not Booting

Jun 21, 2010

I have an older but babied 2008ish Macbook Pro. Today upgraded my 3GS to os 4 with no problem. I downloaded a couple things but didn't go crazy today. I left work and shut lid. When I got home it was stuck on the screen saver password for a long time. I turned off the unit and now it just boots to a white screen. I can boot via OSX disc but it also doesn't see HD. This is a 500gb Seagate drive and I'm screwed if it's dead. Any suggestions to at least get to my bootcamp partition?

View 1 Replies View Related

MacBook Pro :: Most Recent Firmware Update Prevents Computer From Booting?

Feb 24, 2010

I recently attempted to install the most recent firmware and security updates for mac os x 10.5.8 on my macbook pro 17 inch (purchased about 14 months ago). Computer asked me to reboot, i did, it then gave me instructions for firmware updates.

The screen went dark, and it did its thing, and I returned 10 minutes later. The computer had not rebooted.I pressed the startup key and it gave a long beep. Screen remained dark. Some minutes later it ran the boot cycle, but booted into windows (i have dual boot set up). I can only get into windows now.

View 2 Replies View Related

OS X :: Looking For Installed Update List?

Jun 18, 2009

I was shutting down my MBP and i noticed it started performing a software update. After that I powered it back up and tried looking for what update it had performed. I looked in the System Preferences/ Software Update/ Installed updates. Nothing listed in the updates. I fired up software updates and it found a bluetooth update. I figured i would install that and it should come up. I was wrong. Is there anywhere else in OSX 10.5.7 that i can see what updates have been installed.

View 1 Replies View Related

OS X :: Installed Update 10.6.3 On IMac And Use Same On MBP?

May 23, 2010

Are you able to update one computer (iMac) and send to either another imac or laptop? E.g. Installed update 10.6.3 on my iMac, and I able to use that same update on my MBP without having to download it again? Like using the update file I downloaded and installed on my mac and sending (via say bluetooth) to laptop and installing?

View 4 Replies View Related

OS X V10.7 Lion :: Mac Update Can't Be Installed?

Feb 1, 2012

The update could not be expanded, and may have been corrupted during downloading. The update will be downloaded and checked again the next time that Software Update runs.   I seem to get this every time Apple update Mac OS X. Eventually after many many tries it will work , but come on!

Info:
MacBook Air, have numerous iPods/iPhones

View 5 Replies View Related

App Store :: Mac Update Indicated As Installed?

Apr 22, 2012

The Mac App Store tells me there's an update available for one of my applications, however, the install button is disabled and indicates that the new version of the app is already installed. The version number of the app (About...) shows v120...., the update in the App Store shows v121, so there's something available, it seems. How can i either download the update, or get rid of the update indication in the App Store? 

Info:
MacBook Air, Mac OS X (10.7), 13", 4GB, 128, Late 2010

View 8 Replies View Related

OS X :: Wrong 10.5.8 Combo Update Installed?

Nov 3, 2009

I updated a Mac G5 desktop from 10.5.2 to 10.5.8. When I finished I realized I had used the server version of the combo updater instead of the regular one. The machine seems to be running OK. Will this cause problems and how should I fix it.

View 3 Replies View Related

OS X :: Installed Latest Security Update

Dec 18, 2008

I have just installed the latest securtiy update, clicked restart and normal shut down, start up ok, apple in middle of the screen and then the sun burst icon just spins and spins nothing further than that. have tried restarting several times but it always stops in the same place. It's had a half hour to think about this now and nothing, so off to mac doctor tomorrow. [URL:...]

View 2 Replies View Related

OS X V10.5 Leopard :: Update Combined - Cannot Be Installed

May 2, 2012

Any way for installing the automatic update from 10.5.2 to 10.5.8 when getting error: "The update "Mac OS X Update Combined" can't be installed. The Installer could not validate the contents of the "MacOSXUpdCombo10.5.8" package."

Info:
MacBook, Mac OS X (10.5.2)

View 1 Replies View Related

MacBook :: Installed Update And Now Cannot Restart?

Jun 20, 2012

I installed the software update on my MacBook and it never restarted. I have tried most easy fixes but nothing seemed to help. I pulled the drive and then tried to update the software back to Snowlepord but I thnk the install failed. I've seen others with the same problem but can't seem to figure this out.

Info:
MacBook, Mac OS X (10.6)

View 1 Replies View Related

OS X Yosemite :: 10.10.1 Installed But Still Showing As Available Update

Dec 9, 2014

I successfully installed OS 10.10.1 on my IMac (and it shows as being installed) however there is another line item that shows an available update for 10.10.1...how to get rid of the available update ... that is already installed? 

Info:
iMac, OS X Yosemite (10.10.1)

View 7 Replies View Related

Windows On Mac :: BootCamp Update 3.1 Not Installed Properly

Sep 5, 2010

I've installed the Boot Camp drivers that came with the Snow Leopard dvd. Then after everything is installed, I look in the Apple Software Update program for the 3.1 Boot Camp-Update. I try to install this, but during installation several errors pop-up from the bluetooth, trackpad and keyboard driver.

After restarting the laptop, I can't use the functions (like brightness, volume,...) on the F1-F10 buttons anymore. The only solution to make it work again is to reinstall Windows. System Restore or trying to install the original Boot Camp drivers doesn't work. I thought this was just some corrupt download so I reinstalled Windows, but the problem still occurred. I then did it again, but still.

View 4 Replies View Related

PowerPC :: Leopard Graphics Update Not Installed

Jul 31, 2008

I have Leopard 10.5.4 installed and would like to update my graphics with the new patch. I'm getting this message when I try to install: You cannot install Leopard Graphics Update on this volume. This volume does not meet the requirements for this update.

My system is as follows:
1.8ghz PowerPC G5 (Single Core)
NVIDIA GeForce FX 5200
Mac OS X 10.5.4

View 1 Replies View Related

OS X Technologies :: Update 'Java For OS X 2012-003' Can't Be Installed

Apr 14, 2012

When I attempt the update, I get the following error:"The Update "Java for OS X 2012-003" can't be installed.The update could not be expanded, and may have been corrupted during downloading. The update will be downloaded and checked again the next time that Software Update runs." This is on a new Mac Mini (purchased in April 2012) that has been kept updated with all other software updates. I have tried to do this update several times over the last several days with the same error. The computer has been powered off/restarted several times, no effect.I have checked for the Flashback malware, not on my system. 

Info:
Mac mini, Mac OS X (10.7.3)

View 3 Replies View Related

Applications :: Office 2008 12.2.8 Update Can't Be Installed On This Disk?

Dec 16, 2010

The full message is below. I already have updated to 12.2.7 and running the latest Mac OS but suffering continual Entourage crashes, which I'm hoping this will fix.

Office 2008 12.2.8 Update can't be installed on this Disk. A version of the software required to install this update was not found on this volume.

View 4 Replies View Related

OS X V10.7 Lion :: Using Time Machine To Determine When I Installed Update?

Feb 22, 2012

Does anyone know if there is a file I can look at on the system to determine what version of the OS is install?  I'm no longer able to boot once I updated to 10.7.3 and I want to restore from Time Machine back to 10.7.2 but I don't remember the exact date that I did the update.  I want to be able to look at the Time Machine backup files by attaching it to another machine in order to determine when I did the update and restore from that point.

Info:
iMac, Mac OS X (10.7.3)

View 5 Replies View Related

MacBook Pro :: Installed EFI 2.7 Update - No Network Connectivity After Reboot

Feb 29, 2012

I have a late 2011 MacBook Pro 13" running Lion. I installed the recommended 2.7 EFI update (which was advised by the system update utility) and after the reboot, I could not access any network resources (couldn't ping the router). The information provided showed that I was connected to the WIFI AP and had a good IP Address (provided via DHCP). I connected an ethernet cable and got a new IP address in both cases, I was unable to ping the gateway IP address.

I tried clearing the PRAM and NVRAM but no success. I booted into the restore console and the wifi access there showed my Time Machine backup (connected to my Airport Extreme). I was confused by this as when fully booted, it wouldn't show anything on the network, but in the restore mode it could. I have begun the process of restoring from the previous backup which will take a few hours.

Info:
MacBook Pro, Mac OS X (10.7.3)

View 3 Replies View Related

OS X V10.7 Lion :: App Store Update Older Than Installed Version?

Apr 10, 2012

The App Store is showing that an update to Facetime is available, but the update is v 1.0.2 and the installed version is newer; 1.1.1.  When I click the update button I get a dialog that "FaceTime can't be installed on "Macintosh HD" becuase the version of Mac OS S is too new."  The App Store continues to show this update is available, how do I get rid of it?

Info:
iMac, Mac OS X (10.7.3)

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved