just installed 10.5.6 on their last gen. iBook.She left the iBook plugged in to the mains and came back to find that the iBook was alternating between the grey Apple screen and a light blue desktop screen where she could see the cursor. Sometimes it would also switch to a blue screen without a cursor.
I've tried holding shift during startup - no effect.
I've tried rebooting NVRAM - no effect.
I have an iBook G4 (Late 2004) that I just recently upgraded to Leopard using the 10.5.6 DVD included in the Mac Box Set. Whenever it boots, after the chime the screen stays black until the login screen. This happened occasionally with Tiger, but I found a post somewhere where someone suggested to hold the power button while powering on until you hear a beep. That solved it in Tiger, but I have not once seen a grey Apple screen in Leopard.
I forgot to mention that I have reset the PRAM and PMU.
grey screen no apple followed by blue screen with vertical lines. Graphics and logic board replaced <6 months ago. What to do? I held down shift, it gets HOT HOT and makes noises. (for safety mode) followed by a blank grey screen and blue screen. Then tried the other way (I think it's command alt delete? I don't remember) and it turned from grey (no apple symbol) to blue blank. Then third time, grey followed by blue with vertical lines, not blocky clear lines that you can see if you are close to it.
Info:
MacBook Pro, OS Lion
before I went to bed, I was playing the Sims 2, when my iBook G4 crashed. Our power cord can be a bit dodgy, so sometimes that happens. I didn't really think about it much, just closed the laptop and went to sleep.Last Monday morning, I opened it and pressed the power button. It began turning on, and got as far as the grey screen with the apple and the spinning circle. And then it just froze. The circle stopped turning.
I freaked out a bit, and restarted it a bunch of times, each time with the same result. (One time it stopped spinning, and then told me a restart was required. Huh. The rest of the times the exact same thing happened though.) I even tried unplugging and removing the battery, but it made no difference. So eventually I just shut it and decided to try again later.Last Tuesday I opened it and pressed the power button without much hope, and again the apple and circle came up just fine, then stopped, but then a bunch of words and numbers popped up.I'm a complete computer noob, but they don't look good to me... or are they good?
Kernel version:
Darwin Kernel Version 7.9.0:
Wed Mar 30 20:11:17 PST 2005; root:xnu/xnu-517.12.7.obj~1/REEASE_PPC
I am looking at purchasing an Ibook G4 but the description of the item includes this:"When you switch it on it begins to load up i.e. the blue screen with the Apple logo, but then the screen goes black or flickers. Said friend has kindly wiped the hard drive for me so now when you switch it on it makes the �opening� noise then you get a blue screen with alternating �?� and the Finder logo."
I have a feeling this may have been a temporary fault with the screen connector being loose and possibly damaged.But i assume the alternating "?" and the "finder logo" is simply a lack of OS?
I have seen this talked about a fair bit, but i thought i'd start my own thread because it seems slightly different.
To start, when the computer was last running, the (what sounded like fan) started making a terrible noise, then stopped, and the computer turned off.
After that, when booting, it just goes to a grey/blue screen and sits there.
I have an iBook G4, 1064mhz, 256/30.
I dont know what model that makes it, but from the Mac website, I have tried to reset the PRAM to no avail. All of the methods listed do not seem to do anything on my ibook.
I tried using this link to reset the [URL]
I dont know which one is for my model, but i see no reset button under the keyboard, or on the case. There is a little tiny hole on the case beside the LCD???
I have tried the shift-ctrl-opt-power but it doesnt do anything.
As well, i did hold down the "option" button when booting, and it brings me to a screen which shows an image of a hard drive with a green "x"
I dont know if the green means good or the X means bad..
I have read that resetting PRAM and/or changing the resolution seem to help the problem, but I do not know how to do either.
So i bought a 1gig RAM stick for my iBook for Kahlon. Kahlon said that this RAM was supported for my iBook. The specs for my iBook are 12in, 1.2 Ghz, 120gb hard drive and 1.25 gigs of RAM. Ok so I put in my RAM in about March and it worked fine for about 3 months. Then in late July my Mac started showing the "Grey Screen of Death." So i thought that it might of been the hard drive so i did some repairs and nothing changed. So then after that I reformatted my hard drive and reinstall Tiger and nothing changed either. So i finally took out my RAM and tested to see if that was the problem and low and behold my computer ran fine (a little slow because it was was running on 256mb of RAM but it ran fine for about a week). Then I put the RAM back on in it but the Computer only read that the 1gig stick was actually a 512mb RAM stick but it still worked fine for a week until I installed a update and so I had to restart my computer (restart being the Key Word). So when I restarted my computer my computer recognized that it had a total of 1.25gigs of RAM. But when i went to start up itunes or any other application it would immediately show the "Grey Screen of Death." Does anyone know what could have happened I think that it is the Logic Board but I don't know.
View 3 Replies View Relatedmy problem: IBook G4 that recently on reboot is just sitting on the grey screen with the spinning icon as seen here:
what i have done: basically followed apple's tips here
1- booted into safe mode; no change
2- booted into safe mode with shift-command-v to watch the boot; and it just loops around and around; no change
3- reset the nvram/pram; no change
4- booted into single-user mode; ran "fsck -fy" and returned with no errors and "...OK" and rebooted; no change
5- would move on to using my boot disc, however, here is the difficulty- my cd player gave out a bit ago and never replaced it.
so any suggestions? put in a new cd drive? would it recognize it? bring it into the store? i have searched around and haven't seen what to do in my kind of case.
The LCD display on my ibook will get a intermittent blue tint. I have no idea what could be causing it. The LCD seems to be in good shape.
View 1 Replies View RelatedAfter installing an app ('Detour') I was asked to (or it was suggested that I should) restart my computer. I did so, and now my 1.33GHz iBook G4 turns on - but it will not go any further than a blank blue screen (after the initial grey screen that appears.) Thankfully, all my data is on an external drive. I keep my music and footage which I have shot on there amongst other things. I also have a backup on my external via Time Machine of all my data which I keep on the iBook drive, so nothing should be lost.
View 1 Replies View RelatedI just started my iBook g4 up and after the initial grey screen with the spinning thing and apple logo, it just stays at the blue screen straight after that. I have left it for ages and it is still there and I have tried several times now. Does anyone know what the problem is and how I could fix it?
View 4 Replies View RelatedI was given an ibook g4 a1133 but when i boot it all i get is the blue screen with acursor on it which i can move and nothing else.It gets past the loading osx then thats when i see the blue screen, have tried ti install linux but do not seem to be able to boot from the cd using the c key nothing happens .As I am new to macs I need some help if that is possible, so any advice would be appreciated I have no discs with it so am unable see what os version is installed or any information at all, that so far I have been able to get.
View 1 Replies View RelatedEverytime I turn it on I get a black box asking to shut down or restart the mac. I have managed to get it to turn on to powersave and managed to update the software. Thought it might help but just made it worse - it won't boot up at all now past an apple symbol with a little swirly thingy underneath (I apologise now for my lack of intelligence when it comes to computers/knowledge/names of things!) The first time I managed to boot the computer up it came up with the grey screen and a little folder flashing between a face and a question mark which I assume meant it couldn't find anything but that appears to have gone away now. I bought this computer new from Apple about 2 - 3 years ago and no disks were provided with it.
View 3 Replies View RelatedI was on the internet with my iBook G4 the system froze for over 10 minutes so i did a hard shutdown of the system (held the power button) When I attempted to turn the computer back on, the start up chime played then showed the grey apple screen, attempted to start up then went to a blue screen and now stays that way. I have attempted to change the PRAM and PMU to no avail, I also restarted in safe mode but all i got there was a different blue screen with no desktop icons.
View 2 Replies View RelatedWhen I turn on my computer, the wheel keeps spinning and stops on the grey apple screen. If I leave it there for a few minutes, the fan gets really loud.
I tried pressing Apple, Option, P, R, but it only chimes once.
I also tried holding down shift and restarting.
And I tried holding down option and restarting.
I even tried to take out the memory and put it back in.
Nothing is working.
I have the startup disks, but I don't know how to put them in the cd drive.
Since the computer won't boot up, I can't open the tray.
I'm a film composer in the middle of a deadline, and my G5 crashes won't boot again, only get grey screen with Apple and spinning logo.Boot from Applecare disk, run tech tool, hardware fine, disk is corrupted. Catalog B-tree stuff. Cannot re-build without destroying data.Of course I have a clone of my system drive and try to boot from that, but IT is corrupted too of course!Go to Apple Store (I have ProCare), then run diagnostics and find the same. Advice? Wipe the drive and start from scratch.I do just that. I own about 35 plug-in instruments for Logic 8, so it took two days. The same thing happens. Disk won't boot.
View 3 Replies View RelatedMy MBP was updated from 10.5.2 to 10.5.4 (combined update) this morning and, after the installation finished, it rebooted into a blue screen. I restarted it several times and always went into blue screen.
Now, the interesting part is that this is not the "blue screen after install" problem others are experiencing. If I disconnect the external monitor during restart and wait for OS X to start everything works fine. After OS X starts properly I can even reconnect the external monitor and it works fine. In fact I am writing this post from my MBP using the external monitor right now.
Since some document on the Apple Support website was suggesting to remove the file ApplicationEnhancer.bundle in System/Library/SystemConfiguration when experiencing blue screens after the install of 10.5.4, I did look in that folder for that file but it's not there...
I have just updated my iMac G5 to 10.5.6. When I restart, it hangs on the blue screen before log in. I have restarted in Safe Mode (no problem there) and removed the APE files in the library folder, as suggested on support.apple.com. I have also repaired permissions and verified the drive. Still no luck.
Is it really possible that the computer needs hours to restart after the update? And would it be better for me to restore using Time Machine or do an Archive & Install with the Leopard discs? The computer was acting a little funky before I updated to 10.5.6 (iTunes was sluggish), but I never had a problem rebooting.
I was trying to install Windows XP Pro, but for some reason the it wasn't showing another HDD to install Windows on. So I quit the install, and restarted my computer. Now all that happens is the normal grey screen appears (with no Apple logo), then it goes to a black screen and has the blinking cursor (Kinda like DOS).
View 14 Replies View RelatedThing is I got hold of a 1ghz 17" iMac almost for free, it had a dead logicboard (I checked it with a voltage-meter), but I figured I could fix it and have a small hobby project-thingie going on. Well I just got a new logic board today, for a 1ghz 17" iMac g4.
Things is I only get a bright grey screen from my Mac when I boot. I've tried connecting it to a external display and that works fine. Everything is there.
I then reinstalled Tiger on it, with the computer connected to my external screen. And I still have the same problem. (I have now disconnected the ext. screen and is controlling the iMac from my MBP). So at least it isn't the installation.
So what is the problem? I can via an Apple Keyboard control the brightness on the blank screen, which would indicate that it does react to input of some degree.
I've read that if the inverter is dead or anything else is dead, you would get a rolling grey screen, flicker or something like that and not a steady bright grey. One thing I'm thinking is. What if somehow this logic board was for a 15" 1ghz imac g4? Can I check this?
I read that long thread about guys buying hi-res displays for their MBPs, and they had to replace some display profile? Could I maybe fix it with a different display profile-file?
I'm really confused by all this, and would appreciate any help I can get.
Model: PowerMac6,1
CPU-Type: PowerPC G4 (3.3)
and
the gfx chip is a GeforceMX4 with 32mb.
The display is a mode 9c27, manufacturer 610, serialnumber 00000, manufacture date: B84D7200.
I just moved back up to Jacksonville with my friend and now his iBook G4 is not booting. It goes to the white Apple screen and spins for about twice as long as normal, and then goes to a black screen with just a type-cursor in the top left hand corner which erases any text submitted. Now, from there I went ahead and booted from the Tiger Install disk and ran permission repair and also disk repair, without any glitches. Also, we then booted again and ran a hardware diagnostic and it turned up absolutely no problems with the computer. Any ideas? Luckily, he's still under his first year of AppleCare (and he's about to purchase an extension since you can now get it in Florida legally) and he should be covered.
View 5 Replies View RelatedI recently updated to snow leopard and now I get blue screen on start-up.
I manage to get to enter my password and then to my desktop for a few seconds before it flicks back to my login.
I tried using disk utility from the install disc and it said HD appears to be ok. But it hasn't solved the problem.
Info:
MacBook Pro, Mac OS X (10.6.7)
A friend of mine brought over his 14" iBook G4, 1.33GHz, 60GB HDD and 1.25 GB RAM. The problem with it is that upon start-up, the grey screen with the apple/turning gear comes up, then after a few moments a blue screen will appear, though no box showing the start-up process. I've run a few basic diagnostics on this, including the lovely disk utility (which did nothing), I've run fsck, zapped the PRAM, etc, no success as of yet. At one point, I received a screen with alternating folders, one showing the smiley mac face, the other folder with a flashing "?". I cannot replicate this for the life of me. I have attempted to acquire files via TDM, though am not able to see the hard drive despite using 2 different laptops. Possibly the firewire cable itself is spent, though it's brand new! Here is where I become increasingly frustrated: I ask my friend for the boot disks as the ones for my own 12" iBook don't work (for whatever reason). He tells me that he loaded Leopard this summer (currently running 10.5.2, no updates loaded since), then proceeds to bring over boot discs for a MacBook...:headdesk: To begin with, it seemed like the HDD was fried, however, after running disk utility (and not hearing any negative sounds), it does appear that the HDD is fine. I'm thinking a kernel panic, though not sure how to resolve these.
View 11 Replies View Relatedi have a mac ibook..and the screen is like halfway on there..and halfway not..the left two inches of the screen is blue...and everything is blurry except the background
View 11 Replies View RelatedMy iBook will not display anything on its screen. Rather, it just remains black. One time, the screen did come on, but then shortly after booting, it flickered a lot and then went black again. A year ago, something similiar happened and when I took it to be serviced (when I had AppleCare), they had to send it away and have a new logic board installed. Now this machine is out of warrenty and and I am not sure what to do, or even if it is the same problem. Any suggestions?? Thanks!
View 1 Replies View RelatedEver since I sold it here on MR and got it back, there has been a problem with my 12" Dual USB iBook G3 500MHz's screen (lord, that's a long name). Whenever the screen is tilted back farther than 45 degrees or so, the backlight shuts off. I can open the casing and fix it if it's possible. Does anyone know what the problem with it is? I'm trying to get it fixed up and ready to sell back to my friend as his first Mac, and I'm trying to get every problem resolved
View 4 Replies View RelatedMy ibook g4 when starting up stays on the grey logo screen with the loading circle , but won't do anything further I left it on for two days straight to see if it needed time to load but still nothing ... What do I do !?
Info:
iBook
I've been reading the other post and searching for ways to fix this. My ibook froze a couple of days ago, so I pressed the power button to do a hard turn off and then restarted it. It hasn't made through the blue screen since. It seems to load all way and then stops at the end, but stays on the blue screen. The mouse is not frozen though, I noticed that was a problem for some people. So I've already tried a lot of the suggestions I could find. I've tried resetting the PMU,Start your computer holding the ⌘ and S key on your keyboard. When the black screen turns up and the "writing" stops, you will see something like
View 1 Replies View RelatedI have an ibook g4. It freezes at the blue screen with the apply on it. The little circle goes around and around but nothing happens. I took it to an apple technician yesterday who told me the hard drive is toast so I should just throw it away. (Actually, he offered to take the keyboard.) When you do the fsck -fy it says that the hard drive was repaired sucessfully. Is it possible to have a hard drive that is bad and a message which says it has been repaired successfully? I don't mind having the hard drive replaced if that is what is wrong. I do not have any of the install discs any longer.
View 2 Replies View RelatedMy IBook G3 will not start up. I can get the gray apple screen with pinwheel and then after a really long time it will go to a blank blue screen. A couple times it went to the login screen instead but in the user id it says "other" and when I try to enter my username and password it won't recognize me. I am a college student and one of the Apple geniuses here did a check of my hard drive and it checked out okay. We were not able to get it to start up in safe mode; it seemed like it was starting in safe mode but then it came to the login screen and would not allow me to login with my usual information. I was able to start up in single user mode and run fsck which found a couple things and after another fsck it said everthing was fine. But, it still gets hung up at startup. When I try to boot from the OS X installation CD it doesn't seem to be booting up with it, it only goes to the screen to install OS X. According to the directions on the Apple support site when I insert the CD and start up holding down the "c" key it should start up and then I should be able to repair permissions but I can't get that far.
View 5 Replies View Related