I am sharing my internet connect, that I get with an ethernet port, through my airport card on my PowerMac MDD. It only goes for a few hours though, before it randomly shuts off. Do you know what could be causing this? I can't figure it out. I have OSX Leopard installed.
Info:PowerMac, Mac OS X (10.4.11)
I'm sharing my Mac's internet connection over wifi to my iPad when I'm at work. Is there a way to reduce the output power of my wifi? I don't really need a signal beyond my cubicle. How would I reduce the wifi power settings to as low as possible on my Mac when it's in ad hoc mode?
Info:
MacBook Pro, Mac OS X (10.7.3)
I recently installed a VPN.
The performance through the VPN is badly affected by the Airport scanning regularly; often the VPN hangs.
I have deleted the unnecessary wireless networks listed in the Advanced button under Network Preferences. However, the problem persists.
Can you advise how to either stop the scanning or stop it interfering with Internet connection?
For specific reasons, I needed to connect my Synology DS211 NAS to my iMac directly via its ethernet port. I discovered that if I share my wireless internet connection (coming from my cable modem/wireless router) from wireless to ethernet, then the NAS would get the IP stuff it needed to show up. did that, voila, NAS is acting like a glorified external hard drive. BUT, when I did that, I lost all internet connectivity on my iMac. Still have full wireless signal. preferences pane says I'm fully connected to my network with an IP address, but safari always fails to pull up any webpages, saying I'm not connected to the internet.As soon as turn off the ethernet PORT, it all starts working again. And to make it even crazier, I discovered that if I leave sharing my wireless internet via my ethernet port ON, but turn off the ethernet port (in pref pane), I can STILL access the NAS just like before. That makes no sense - I'm sharing my internet via a port I have turned off, but it works? Anyway, why would Iose my airport wireless internet connection when the ethernet port is on - configured manually?
Info:
eMac 1.25GHz & iMac Intel 2.0GHz Intel, Mac OS X (10.5.8), 80GB external FW, 1GB RAM, Superdrive(DL)
I have a macbook pro with Mac OS X 10.5.8 with a 2.26 Ghz Intel Core 2 Duo processor. Recently I've been having a problem with my computer when applications would randomly stop to respond for a few seconds, until after a while they wouldn't start again and I'd have to restart it. I don't know what to do. I'm a fairly new Apple user.
View 3 Replies View RelatedI have successfully created a script to resize images. Now, everytime I clik on a file or on a folder Automator runs that script and I get promped to select the file to resize. How do I stop or control this?
Info:
MacBook Pro (15-inch Mid 2010), Mac OS X (10.6.8)
it shows in the sharing section of my sys preferences that a "Remote Management service" is controlling it. I am the only user on my comp. and there are no other computers in this home.
Info:
MacBook Pro (13-inch Mid 2012), OS X Mavericks (10.9.5)
I have 2 new Apple TVs, I have 1 Second Gen Apple TV, I also have a new 3rd gen iPad, and a new iMac. Since I got the new iPad and new Apple TVs, iTunes Home Sharing stopped working reliably. I say this because this is when I noticed it. I had not really used home sharing much in the 2 months prior because I sold my old ipad in anticipation of the new one. When trying to access my video collection on iTunes, the iPad and AppleTVs will see my iMac's Video collection, but when selected, it thinks awhile and then the % indicator goes to 50% and stops waits awhile and then indicates that there are no videos.
The only way to get it to work again is to Stop Home Sharing on my iMac and then start it again. Then it works instantly. Less than a day goes by and bang, the problem comes again. Because I can get it to work via iTunes, I have to assume that it is a software issue and not a wireless router issue (im using an airport by the way). I don't know if iTunes is having a hard time keeping up with that many clients (the ipad and 3 apple TVs), or what, but the issue is very annoying and really ruins the Apple experience.
Info:
iPad, iOS 5.1
I've got a new Mac Mini Server that I'm using to set up file sharing for the first time. I've enabled OpenDirectory and verified that the users I'm creating are being created in (they show up in the Server app and Workgroup Manager app, but not in System Preferences | Users).
File sharing seems to be working fine, but I don't like the fact that each user has access to their home folder share when they connect to the server using a mac elsewhere on the network. I prefer only the shares I explicitly set up to be available.
Thus, a couple questionsWhy is there a home folder created on the server at all? Do I really need a /users/johndoe folder for each and every account in OD?How can I configure sharing such that I won't see the home folder when I connect from another mac on the network? I don't want to leave little "cubby holes" for my users to stuff files into
I have a mid 2010 macbook pro. I recently had to get a new hard drive and the guys at the Apple store went ahead and updates my software to mavericks. I hadmt had any problems for over a month. However, I've started having a problem with connecting wirelessly. Whenever I first open my laptop, it starts to connect to wifi, but comes up with the ! symbol. I know it's not the wifi because all my other devices haven't had a problem and it's been happening on my home and college wifi. At school, I'm able to just turn off airport and turn it back on to get a connection. However, if I do this at home, it initially connects (it shows signal and I'm able to load pages) but drops within a couple minutes. If I turn my router off and on, it connects.
Info:
MacBook Pro, Mac OS X (10.6.8)
Except for the drive with the system on it the drives (whether CDs, DVDs, Sata Drives, internal drives, Firewire, network,...) drives only mount randomly. And often after ejecting them they often don't disappear and stay on the desktop. I've got a couple of Raids (one internal and one external Sata II) and one of them is hardly ever recognized on startup and I have to get it in the disk utility. Most recently even toast has started to fail if asked to copy cds or dvds (I presume because they are not mounted proplery).
Information:
G5 Quad
My problem is I keep loosing 'Internet' signal on my network, the network still runs fine and all computers (macbook, imac and macbook pro) are still connected to the network and can still transfer files but there is no internet connection. Im not 100% sure but this seems to happen once more than one computer is on the network at once. It happens randomly and their seems to be no real sequence or pattern as to when it happens.
I was adviced to change the ports on my router from 11 to say 6 or others, this didnt seem to help, and i have since thought as my imac is hard wired with an ethernet cable this wouldn't effect this computer as it is not connected over wireless but this computer IS still affected.
I have tried numerous hard resets and fimrware updates etc but no joy, the router i'm using is a Belkin URL
For a while now, my Airport will randomly stop working when browsing the internet. What I mean by that is that when browsing the internet and then trying to open a new tab, it will not load the page I am trying to open. The Airport icon still shows that it is connected, but no pages are loading. I have tried multiple browsers to no avail. As well as restarting.
I am running Mac OS X 10.6.2 with all updates applied.
My brand new imac randomly disconnects from the internet. We have a BT hub - wifi. I have googled this issue and see that it is relatively common and it is incredibly frustrating. It is fairly simple to reconnect each time but it is driving me mad having to. It generally happens when the computer is asleep but sometimes in the middle of doing something.
Info:
iMac
I have a 13-inch Macbook, Late 2008 model, using iOS Mavericks. While on battery power, the laptop will randomly just turn completely off, despite still having plenty of battery power left. I know it's not a calibration issue where the battery is dead but appears to have charge left, since I'm able to turn the computer back on again and continue using it.
Battery info:Charge Information: Charge Remaining (mAh): 606 Fully Charged: No Charging: No Full Charge Capacity (mAh): 2609 Health Information: Cycle Count: 157 Condition: Service Battery Battery Installed: Yes Amperage (mA): -1265 Voltage (mV): 10855
I'm am currently sharing my Internet via Airport to my MacBook and PC. The only problem is that the PC won't connect unless there is no password protecting the network. Why is this? What am I doing wrong?
View 4 Replies View Relatedim having issues with my internet is randomly crashes saying safari quit unexpectedly while using the iLeadDVDCopy.so plug-in how do i resolve this issue i've updated the software but still it keeps happening
Info:
MacBook Pro, Mac OS X (10.6.8)
So far I haven't been able to get an airport connected computer to share its connection via ethernet with another. Am I doing something wrong or is this not possible?
View 2 Replies View RelatedMy macpro for some reason doesnt have the signal catching strength of my macbook. I want to temporarily use my macbooks internet on my mac pro. I went to sharing and clicked share internet and plugged them into eachother via ethernet, but it didnt work...or i just did it wrong. Is there an easy way to do this?
One weird thing, I clicked on the wireless icon nd clicked create network. i created a network and enabled data sharing...i was able to access all the file on each computer respectively without plugging them into each other....how does this work? If they can share data without being plugged in why cant they share internet!?
Ok... So I set up my MacBook a day or two ago to share my Ethernet internet connection via WiFi for my iPhone. All and dandy. Cue about an hour ago. It just stopped working.
I can access the internet via my Ethernet connection when Internet Sharing is un-ticked. I then proceed to tick it and the Internet connection drops. So I un-tick again and internet is working again. My Airport creates and connects to my iPhone all ok. But, I cannot access the internet.
Also, when Internet Sharing is ticked, Little Snitch tells me that "natd" is trying to talk to 0.0.0.0 via Labrat (DIVERT port 2560).
I tried searching but wasn't able to find anything extremely helpful. But I want to share files to a PC over the web. I have a TC and mobile me as well and not sure if the PC can get to the shared disk. I know my mac can connect to server in finder. I've read things about hamachi and that seems like a viable option. Sharing iTunes would be nice as well. But I imagine my computer would have to be awake for it to work. Would it be best to setup an FTP client or SSH?
View 3 Replies View RelatedI can't seem to get internet sharing working on my mac after installing a new router. I want to share my airport connection with my ethernet port so I can get on the internet with my Windows 7 test desktop that doesn't have wireless capabilities.
I used to have a DLink DI-614+ router and it just broke on me last week. Now I have the Belkin N+ Router model F5D8235-4.
Before, when I turned on internet sharing with the DLink router, everything went smooth and I could automatically connect via ethernet to the internet, but now when I attempt to connect it says that there is no internet access on the Win7 box. I assume this has something to do with the new router that I installed.
One thing to note is that My Ethernet in Network preferences says that it "has a self assigned IP and may not be able to connect." Is a self assigned IP the problem and is there a way to fix it by modifying the network preferences or is there something I have to do to my router to get this to work.
Since I have installed Snow Leopard I can't use the function in internet sharing that allows you to share your connection from ethernet to computers using Airport. Has anyone else had this problem? Anybody have ideas for a fix?
View 16 Replies View RelatedI've got an LED unibody MBP and for a month or 2. I've been internet sharing my connection from my HSDAP broadband dongle to my Xbox 360 through an ethernet cable. It took me AGES to get going! A while ago I upgraded to Snow Leopard and it broke it. I have no idea why, and i spent hours yesterday trying to get it to work again to no avail! [URL]. That is the guide I am using and for the most part its fine. Long story short, the DNS keeps failing. "Move onto DNS. Enter the IP address of your wireless router (in my case, "192.168.0.1") in both the primary and secondary IP address fields". Thats the part I am having problems with, as I don't use a wireless router, i dont know what to put in.
View 1 Replies View RelatedMy xbox and mac are both connected by router by an Ethernet cable. When I go to internet settings it say I might violate the terms of service of my isp(att yahoo dsl) Does doing the steps in the above link, will it affect anything that will violate the TOS, is their another. Safer way to connect the 360 to my mac?
View 1 Replies View RelatedI have my cool new mac here and it's got a great printer connected to it via usb. My mac is accessing internet via an ethernet cable, awesome! I have internet AND can print on my mac. now we got the old family PC in another room and it really wants to print and have internet access. So I try to get my mac to help it out by using the built in airport to give it some wireless, and access to the printer via wireless. well I do that and the PC can connect to the shared network, but uh oh! we might have a few pesky snoopers around so I want to put the WEP on just to be on the safer side. Ouch, turns out PC and mac WEP aren't so compatible so what is my PC gonna do now. Well what it's gonna do is connect to local wi fi for internet, but now it can't print! I wonder if theres a way to SECURELY connect to my macs airpot from my PC or maybe theres a way to print wirelessly from my PC thats on a different network.
View 4 Replies View Relatedmy imac is connected to a wireless network that my psp cannot access, and im trying to enable internet sharing through the Ethernet port and connecting the ethernet to the WAN port on my wireless router. but for some reason this wont work because my psp says there's no internet connection through the network.
View 1 Replies View RelatedI used to be able to use Internet sharing without any issues. I share from ethernet 1 to wifi so my iPad etc can have strong wifi everywhere etc.
Everything is the same, I can set it up but when I check the box and then hit start, the airport icon flashes between a hollow shape and the bars a few times and then nothing happens. When it works the icon has an arrow in it.
Info:
2010 2.8 Quad MP 15" Late 2008 MBP 2.53Ghz 4GB 16GB iPad 32GB iPhone 4 , Mac OS X (10.6.5), External WD 500GB My Book Studio 1TB Seagate 160GBx3
had internet sharing on my imac before upgrade to lion, now nothing.
Info:
iMac, Mac OS X (10.7.4), had it before update to os x lion
My internet provider says it has a good signal. whether i use wifi or connected straight to the modem its the same, some pages load some dont, always different on what loads and doesnt. If i connect to a neighbour who has the exact same internet speed and provider it works perfectly fine. Ever since i did a software update 3 or 4 days ago it has been happening.
Info:
iMac, iOS 7.1.1
