I just got my MBP logic board replaced by Apple, and now it works fine, but when I press the power button, my computer freezes and this happens:
I'm probably bringing it to an Apple certified repair center, but I don't trust them as much as I do the Genius Bar, plus I'm pretty good at DIY stuff, so is it possible to fix this by myself?
I have a macbook pro, bought it May last year(2008). I don't know much about computers, but I loved the transition between pc and mac, had no trouble with it, loved to work with it, until now. I had noticed it became slower like 3 weeks ago, and a week ago, it started to freeze up on me followed by a message that said please restart your computer by pressing the power button and the screen becomes dark. When I try to restart it again, it takes a while because it shuts down again and again, until the 10th time it works. The store told me to clean intall, which I did yesterday, it seemed to have worked, it was faster for sure, but today it happened again, 3 times! Has this happened to anyone? Does somebody know what to do?
View 4 Replies View RelatedWhenever I open my mac mini it comes up with the same message "You need to restart your computer hold down the power button or press restart" in four different languages.
View 2 Replies View Relatedmy brother is having a problem with his unibody MacBook that he bought just a few months ago. It won't start when the power button is pressed, the sleep indicator light turns on and that's all. There's no start up tune, and nothing appears on screen. I had a similar problem with my MacBook Pro. I was told that the logic board needed to be replaced due to too much dust or moisture. Could this be the same problem? and has anyone else here ever had the same problem?
View 2 Replies View RelatedWhen I press the power button a grey screen comes on and it won't go away
Info:
MacBook Pro with Retina display, iOS 7.1.1
I have macbook Pro running OS X 10.9.4 purchased in 2012 times. For past few days, I've noticed this problem- I have to long press the power button to switch on the device. Normally, the devices switches on with a simple press on the power button. But for the recent days, when I do a simple press of the power button, I think it switches on and goes off instantly. I had to long press (for around 5-8 seconds) to switch it on. After the device is on, there is no problem at all...
Info:
MacBook Pro, OS X Mavericks (10.9.4)
macbook air 2013 needs power button pressed for 10 seconds before it turns on? also I've tried resting PRAM but when i press the 4 buttons before the start up screen it never restarts again?
View 2 Replies View RelatedI have a iBook G4 laptop and there seems to be something very wrong with it. It started a few days ago just randomly. I was reading something on the internet and the screen went black on me, but the power was still on (I clicked CAPS LOCK to see if there was power). I then proceeded to push the power button and the power went off. When I pressed the power button again to turn it on, it made that internal noise it always makes and then the fan came on, and wouldn't turn off. There was no picture on the screen at all. Completely dead. But there was power, because when I clicked on the CAPS LOCK, the light came on). I tried pressing on the power button for at least 15 seconds and even went as long as a minute, and the power didn't go off.
View 3 Replies View RelatedWhen I press the power button on my macbook it goes to the loading screen and stays there. It don't freeze it just keeps loading. I dropped it on the floor today but it worked after that.
View 10 Replies View Relatedis there a way to setup my MBP's Power Button to make the laptop directly and without opening additional windows enter sleep mode?Closing the lid to enter sleep mode is no solution
View 4 Replies View RelatedWhen I was working on my MBP last night I noticed the computer slowing down, then a sheer black wash went over the screen and a prompt saying I need to manually power off and then power on the computer with several different languages below. When I did that the computer made the on sound, opened up to the apple logo in the center and the spinning gear below. But its stuck there! I can definitely hear the laptop running but it hasnt budged for the last 12 hours.
Info:
MacBook Pro (15-inch Mid 2010), Mac OS X (10.0.x)
I have just shipped my Mac Mini to its new home and I've had reports that the panic error is appearing on boot up: "You need to restart your computer. Hold down the power button for several seconds or press the Restart Button." This screen appears on the blue window just after the grey apple screen has disappeared and does not get as far as the desktop at the same point each time. We have tried to reinstall mac OS from the original install disk but holding the "C" Key or the "Option" Key down on restart doesn't boot from disc. Is there a way you can view the Kernel Panic log before you boot into Mac OS so we can try and pin point the source of this problem. I'm wondering if this could have been the result of the shipping that has caused some hardware to come loose.
View 3 Replies View RelatedMacBookPro15.4 less than a year old keep freezing/locking with black dialog box to press power button until off and restart THEN repeat successive times after restarting it?
Info:
MacBook Pro, Mac OS X (10.6.8)
When I leave my macbook sitting with no activity for a while it freezes up. There is a logo on the screen that looks like the power button and it says i must resart my computer it is in english and 3 other languages. Why is it doing this? I tried to verify and repair the permissions with the disk utility
Info:
Mac Book Pro, Mac OS X (10.5.7)
I have to hold the power button down for several seconds to force it to shut down.
Info:
MacBook Pro
When I go to insert music to my movie in iMovie, I cant press the music button.
Info:MacBookPro
I have brought the 21,5" iMac 1 week ago. I just chosed the preconfigured model.
But i have had some problems with it.When the computer has been to sleep for some hours, it wont wake up with click on keyboard or on the mouse. I will have to use the powerbutton, where the computer then comes with a error, but it starts up.
So I'm having issues with the computer not waking up in the morning. I guess it goes into a deep sleep of some sort and I have to hold the power button twice to turn it on, and get greeted with a computer experienced a problem message on login.
The most recent log in the system diagnostics is titled:
aosnotifyd,diskarbitrationd_2014-08-21-184310_MacBook-Pro.shutdownStall
And the brief details are:
ate/Time: 2014-08-20 22:02:42 -0700
OS Version: 10.9.4 (Build 13E28)
Architecture: x86_64
Report Version: 18
Command: No Target
[code]....
Info:
MacBook Pro (Retina, 15-inch, Mid 2014), OS X Mavericks (10.9.4)
Got a tricky one here: powerbook G4, 1.25ghz, 1GB RAM (2x512), 80gb HD, APX, 15" LCD, serviceable battery, SuperDrive, OS: 10.4.11. It was brought to me with a boot problem: Computer turns on, gives the start up sound, backlight comes on, apple logo shows, spinner spins... then you get the dimmed screen, large option icon and "You must hold the power button and restart your computer": a kernel panic. I've seen this a few times before and the last time, I fixed it with a new hard drive and the removal of RAM from a bad ram slot.
What I did was:
1) Replaced existing 80GB HD with a backup 30GB drive. Then booted with a Tiger CD (the computer won't start with my disk warrior cd, nor with a tiger DVD). I was able to install Tiger and restart the computer. But the airport card doesn't show up. I tried a known good airport extreme card and this too has not shown up.
2) I hooked up the 80GB drive to my PC via MacDisk and checked it. Sure 'nuf it had loads of problems. MacDisk went through and fixed it (I'm not sure what the problems were as I'm new to MacDisk and don't know what it's looking for and fixing when it does).
3) With the computer running the 30GB known good HD, I started having the same kernel panics so I removed the first RAM chip (512MB) and tried to reset the PRAM.... here's where it went wonky. (I know, only change one thing at a time...)
4) As I said I tried to reset the PRAM (Option, Command, P, R, at start up). While I can get the computer to not boot, it won't restart. I don't know if this is just unique to this machine. Next I tried to reset the NVRAM and again got nothing. The screen wouldn't come on at all. After about three or four resets, the computer did start in Open Firmware mode. I reset the NVRAM from there and restarted (reset-nvram, reset-all). Still nothing on restart.
5) After trying to start it 15 times like this, I swapped the bottom RAM card to the top slot and removed the airport card (again, I'm stupidly trying to change two things at a time). BAM, computer boots... I put back in the 80GB drive that's been "fixed" by MacDrive and BAM, that boots fine too.
So then I put back in the airport card and it will boot, but won't recognize the airport card. I've re-seated it about a dozen times and have used terminal cleaner on the card and on the socket for the ribbon cable from the card slot to the logic board. As it sits, I can't get the airport card (either of the two) to show up at all. I did realize that the open firmware did reference a problem, but I forget the code now and when I looked it up, the references were to a failure of the airport card, but there were also more general references, so I can't be sure.
I'm thinking now that it's the airport card controller on the logic board, the bottom RAM slot and a corruption of the hard drive. Yes, there was a history of moisture into the device and I think a drop in it's past too. I'm the Mac repair technician for the people at the local bike shop, so I get to trade my repair work for their bike repair work. The problem is that they ride their laptops like their bikes, hard and greasy. I'm really wondering about ways to get the airport card back up and running. Or, baring that, a good card-based wireless adapter that I can slide in.
The computer doesn't respond to the power button when pressed. (imac - no intel)
View 1 Replies View RelatedMy Macbook pro is not booting properly. When I start it up, it goes through the normal process and gets to a point where a screen comes up telling me: "You need to restart your computer. Hold down the Power button for several seconds or press restart now" This happens every time. I tried to start in safe mode and holding down the option key and selecting the mac partition. Neither would work.
View 3 Replies View RelatedWhen I go to insert music to my movie in iMovie, I cant press the music button... ? Why??
Info:
MacBookPro
In OSX 10.9.2 [mavericks] when I shrink a document [yellow button] where it goes nor how to retrieve it. Sometimes they stay for a while in 'application windows' but then soon disappear. Does they are visible somewhere as thumbnails and can be retrieved as I used to be able to do in snow Leopard?
Info:
iMac, iPad
recently, my mouse has been having a lot of trouble holding its "click". By this I mean when I, for example, attempt to drag a file folder to folder or even drag a window around, it loses the "hold" and usually ends up dropping the file and clicking something else. Oftentimes if i right click hold it will lose the hold and select something else in the menu.Does anyone have any ideas as to what the problem might be? I'm not certain that it is a hardware problem either, if maybe it is something to do with my iMac itself?
View 1 Replies View RelatedI have macmini like mediaserver. But when internet is mising, or error when iTunes can't get album artwork it display dialog window. And i need conect to serve via VNC, and press "OK" Botton. What app can close this widnows avtomaticly? AppleScript?
View 2 Replies View RelatedMy HP Photosmart 3210 all-in-one wouldn't initialize and sent error messages after I installed Snow Leopard yesterday. I went on the HP support network, which gave me a solution that sometimes works and sometimes doesn't, plus in the past I never had to take all the extra steps to scan a photo. The HP support site claims that upgrades for HP Printer devices was included with Snow Leopard. So why can't I just press the scan button like I used to?
View 20 Replies View RelatedMail on my Mac used to check every few minutes automatically. Now it only come sin if i (a) relaunch the mail programme or (b) press get new mail button. Why has this changed and how can I get back to it being done automatically?
Info:
iMac, Mac OS X (10.7.5)
I have a late 2008 uMBP 15 inch and in safari, regardless of using the integrated graphics card or the higher end card, when I press apple t for a new tab the computer hangs for at least 10 seconds then once it finally loads the top sites page it appears all scrambles for a second, then it works normally.
My second problem is that my hinge is very loose. I can't hold the laptop at 45 degree angle without the screen falling down and closing. Will apple fix this?
Power MAC G5.
Press power, lights up, fans BEGIN to spin then shuts down. Within 1 second.
Tried:
New RAM, new set of Processors, Video, Hard Drive.
Motherboard or Power Supply?
I think I have found a flaw in OSX 10.6.4 file copying..I normall back up my files, by dragging from a folder on my HD to an identical folder on my external HD.The folder I am copying has 86 files in it, but there are only about two dozen new files added since my last back up.I have been telling it by the dialogue box, not to replace identical files in the back up folder, and clicking the check box to apply to all."but when I press the dont copy button, in the copy progress box it says it is copying 86 files. WTF is going on...!@#$%^&*().
View 6 Replies View Related