MacBook Pro :: 2010 13'' Only Charges When Screen Closed?
May 6, 2012
If I have a half-full battery and adapter plugged in, the indicator light is green and a "not charging" is shown on the top bar in screen. And the power in the battery will decrease in a speed between 0 and battery-only.
If I use a empty battery and adapter plugged in wall, the computer can start and run a few seconds/minutes and it will shut down randomly. If I closed the screen, the indicator light will finally go amber and begin to charge. I change battery and megasafe and it is the same.
I feel the reason is my mother board is not able to aquire enough Watts from the megasafe to support its normal running. So it consumes power both from megasafe and battery.
I have 3 problems with my aluminum macbook and I think that they are all related and are caused by each other.1) The hinge creeks sometimes when I slowly close the screen and I'm afraid it will only get worse as this just started happening.) When the macbook is closed, the screen is uneven. The right side does not completely close and there is a gap between the base of the computer and the screen. However, the left side is just fine unless I push down on the right side then the left side just goes up and becomes uneven.
Is there a way to show login screen only when I close the lid of MBP but not when it goes to screen saver mode? So far I only found the setting including both in "Security" section in settings.
When the screen on my MBA is closed down the rubber edge on the bezel around the screen does fit tightly on the left side, but on the entire right side, there is as small gap between the rubber edge and the base of the MBA. At the rear right the distance between the bezel and the base of the MBA is one milimeter and since the rubber edge takes up less than half of that distance, I'd say the gap is at least half a milimeter. Does your screen fit tightly all the way around or is a small gap normal? I'd think the rubber edge not only avoid metal against metal, but it will also prevent dust or dirt from entering the screen / keyboard / touchpad area when transporting the MBA.
I'm very new to Macs (4 days) and hope to get involved in video editing on a professional basis. I have matched my 13" macbook pro to a 23 inch widescreen monitor and wanted to inquire as the best way to keep the macbook pro ON, but also save on space. I have heard of 'Insomnia' which disables the sleep function on the mac and wanted to check if, by dimming my screen down to off (the minimum brightness the screen will go) and turning on 'insomnia' will that be enough to prevent the screen/unit from overheating?
I've got a late 2008 15" unibody macbook pro. For some reason, the screen won't turn off when I close the macbook. The Apple on the back of the computer remains on and I can see that the screen hasn't powered on at all.
Is there any way to set my macbook pro to shut off rather than going to sleep? My problem stems around my family not shutting off the computer after they are done using it. They will simply shut the lid, putting it to sleep. Normally, this isn't a problem, but the computer then may go unused for days which then leaves the battery depleted. I cannot get them to shut off the computer, I could set the computer to shut off when the lid is closed rather than go to sleep.
I've had the new macbook air just two days now. Turned it on this morning, used it for like 5 minutes and the screen just started flickering, and the whole machine just froze on me! Had to do a system reset, but I'm a little concerned after spending over a grand on this macbook! Has anyone else experienced this? I'm actually thinking about returning the machine..
I recently set up my new macbook pro with an Apple Cinema Display. The setup is great except that my wifi connection only works when my MBP is open. The second I close the screen the connection stops working. It's not a proximity issue since it works just fine when it's open.
I am on a 17" macbook pro using lion and my laptop wont go to sleep. I shut the lid and the screen turns off but I hear it still going and the light in the front doesn't begin to blink like it is suppose to. I have reset the pram and the smc and its still not working
If you connect say a 13inch macbook to a 19inch monitor using the closed clamshell mode, will the picture quality on the monitor be like a stretched out version of the 13inch screen? I.e. poor, or does the macbook just act like a desktop computer and allow high quality viewing.
I've had my 11" ultimate for about 3 weeks. Its mostly used by the wife around the house so I never really noticed before that the battery never charges to 100%. I'll leave it plugged in overnight. Open it up and it tells me it charged, however as soon as I unplug the cord it reads 99%. Does anyone ever see 100%? I know it really has no bearing on battery life, which is great on this machine, but all my previous laptops have said 100% when fully charged?
So I just go a new umb 13 and since opening last week the battery only charges to 99% after the first charge (went to 100% only the first time). I ran it down once to see how long the battery would last and when i recharged it, it says its fully charged but only at 99%. I then tried calibrating it but it once again stop at 99%. It has 3 load cycles so far. Is this normal? if this has been asked before im a newbie to a mac and i tried searching for it but couldnt find anything.
Bought a new MacBook Air 13" a couple of days back, i let it run completely run out of battery to then fully recharge it to get full battery life... i plugged in my MagSafe Charger and left it for a few hours, i then returned and it had finished charging (MagSafe light was Green) i then turned the machine on and it was only at 98%... is this normal for first full recharge?
I have an 13" MBP that I ordered new in April, 2012. It is running Lion. I have an external monitor that is capable of 1440x900 resolution. I have an external keyboard and trackpad hooked up, and I like to close my MBP up and stick it in a BookArc. I want to be able to have the internal display disabled and to have the MBP only allow me to put windows on the external display, so long as the lid is closed. I also want to be sure that I am taking advantage of the resolutions available on my external monitor, which are higher than those supported by the internal display (specifically 1440x900).
This doesn't seem to work because I either have to allow the MBP to continue to draw my desktop across both screens (internal and external), OR use the "mirror displays" mode, which restricts my resolution of my external monitor. This means I either forgoe the additional resolution benefits of my external monitor, or I end up with windows that fall off-the-cliff, so to speak, because they are drawn in the portion of the desktop that would be shown on my internal display (which is closed).
I've read the community support pages on using the MBP with an external monitor, most relevantly, this page. It simply recommends using the "mirror displays" option. However, this option, as I mentioned above, doesn't allow me to make use of the additional resolution, and my external display looks bad. how to keep the 13" MBP in closed clamshell position, with the internal display disabled, and use my external monitor at resolutions higher than those allowed by the 13" MBP but which are available to my external monitor when not in "mirror displays" mode?
Info: MacBook Pro (13-inch Late 2011), Mac OS X (10.7.3), External display (1440x900)
After try to get it out of sleep mode the screen stayed black
Tryed to turn it on several times (magsafe or batery)
Reset the PRAM
Reset the SMC
Tryed Safe Mode
Tryed everything I've found about it but the screen is still black. The mac is on, can hear the fan and the lion start cause when I press a key I can hear a "bump"
Is that a know issue? Does apple offer an extra warranty period on this issue because it seems to be a comon issue on this machine.
Is there a difference? Anything at all? I would expect Apple to make the 2010 standard res. screens worse in quality and earn more money since they have the higher res. available. I really like the 2009 glossy screen, but i have to be sure it is exactly the same this year. If they did something like that it's typical Apple.
I upgraded from my old 13" Uni macbook to the 13" pro and I have not been impressed with the battery power. I get about 4 hours with half brightness, wifi on and light web browsing. Yes, i have checked activity monitor, CPU hangs at like 5% the whole time...Does this sound right? Furthermore, the battery will charge from 5%-10% to fully charged in little more than hour, like 1:15..that seems like an awfully short time to fully charge such a big battery...
Coco Battery reports only 1-2% wear with just a few cycles. I have conditioned the battery to no effect.
I am wondering that is it essential to connect power adaptor all the time while operating in closed calmshell mode? When I unpluged the cable it didn't work. Is there some way?
My MacBook Pro 2010 15 inch screen shuts off randomly. The whole laptop doesn't shut off just the screen. It calls it a panic but I have to hold down the power button to shut it off when this happens or it will stay on the black screen.
This is my first post on Macrumors and unfortunately it is in regards to a problem that I am currently experiencing with my brand new Macbook Pro 15" w/anti-glare upgrade. I purchased the unit on the 28th May and have used it without problems for until yesterday when I noticed some intermittent flickering in the screen generally a horizontal banding that happens quite sporadically and also changes in brightness levels etc. I checked in with an Apple store earlier today and a staff member at the Genius bar couldn't figure it out either. She tried installing new firmware, but the problem remained and told me that she suspects it is an issue related to the firmware as opposed to hardware. The only advice was to wait it out until Apple addresses the issue with a new firmware upgrade?
I can honestly say I'm not very impressed since this MBP was my supposed long-awaited transition from a lifetime user of PCs to the supposedly more stable/reliable Macs! Just my luck I guess. Nonetheless not a great start to my Mac experience. Anyways, just wanted to see what is the best way to go about it and whether I have the right to demand for an outright replacement (I will be heading off overseas on the 24th June and will definitely need it while away), which may be an issue in itself as I don't think any retailers (I'm located in Sydney) have the 15" w/anti-glare model on hand/stock - mine took over 2 weeks to arrive via a special order. Peoples thoughts? Anyone else experiencing similar issues? Only thing that I could find of relevance were the problems experienced earlier this year with the 27" iMacs.
I've had my MBP for about 2 weeks and yesterday a white vertical line about an inch long appeared on the right edge of the screen.
It went away after a restart, so I thought nothing of it, but now another one has appeared. Picture:
They mostly appear only on the desktop, but occasionally crop up when I'm running apps.
Is this something I can fix or is it a video adapter issue? I have searched and come up with some similar motherboard issues but they are mostly older macs.
My MacBook Pro 15 inch mid 2010 model i7 processor is having problems when I close the lid and the computer goes to sleep. Heres how my problem is occouring. I close my macbook pro lid. After waiting about 10 min (my macbook sleep time) I lift the lid. Once I do this i see the screen.... for about 2 seconds and it suddenly goes black. I fix it by turning my brightness down 1 bar then turning it back up 1 bar. I dont remeber this happening on snow leopard it seems to be a lion issue and a lot of other users are having it.
Info: MacBook Pro, Mac OS X (10.7.4), 15 Inch i7 processor Mid 2010 model
I have had my 13 in macbook pro for about three months and suddenly it does not charge when it is plugged in. In the last week this has started to happen but upon fussing with the connection like unplugging and replugging in the magnet charger it would start for a while and stop randomly. Now I can not get the computer to charge at all no matter how much I fuss. Do I need a new adapter or is there some other problem?
