I am considering replacing my G4 Mac mini, which is used primarily as a desktop. It turns out that my computer desk is very close to my Sharp Aquos LC32GA5U TV. With the right adapters, it should be possible to have my monitor and TV connected to the new Mac mini at the same time. The DVI/HDMI cable to my TV should be about 12 ft. I have some questions about a setup like this. Will a video cable of this length cause any issues? My TV will not be turned on all the time. Does Leopard recognize the fact that a display is turned off and prevent apps from putting their windows on it?
I have a new Mac Mini connected to an older VGA monitor using the Apple brand VGA adapter. The mini is fully up to date and runs perfectly when booted. However, if I reboot the mini with the VGA monitor connected, it fails to boot. I just hear the faint chime sound every other second. There is no output to the monitor and the only way I can get it to boot is to disconnect the monitor and then power cycle the mini. I can reconnect the monitor just seconds after powering back on and it finishes booting properly.
I've also tested with an HDMI connected monitor (without the VGA adapter) and it boots just fine and the display works properly.
when I connect my macbook unibody with dvi to my dell monitor the quality of the screen is not as "good" as when I connect my windows pc to it. Is this only a problem on macbook, or is the mac mini the same?
I have a 13" MBP and just bought a new 23" external monitor connected via mini DVI to HDMI adapter.The monitor is recognized fine, but there is extreme jitter on the screen - basically very annonying and unusable.
I bought a MBA 13" last month and now I'm trying to connect an external monitor through a Mini Display Port-to-HDMI adapter and most of the times the display shows a message "No signal detected"...
I've tried all the possible combinations between the MAC and the Monitor but it would seem a random matter.
Info: MacBook Air (13-inch Mid 2012), Mavericks 10.9.4
I hooked up my macbook pro to a mini display port to a dvi -> hdmi to my tv no problem. However, when I hooked up the mini display -> dell monitor, I get nothing. The screen is black. The weird thing is that my macbook pro recognizes that a second monitor is plugged in... it just won't display anything
I was surprised one day to find an inch of white line running from top to bottom on my screen. Then after a week it expanded to two inches white line, then suddenly it turned all black and I can't see two inches of my screen from the right edge. I was reading some forums and found out that I can use a dell monitor as a secondary monitor, but is it possible to use the dell monitor as the primary monitor in case the black line will spread throughout the entire iMac screen? so the iMac would serve as a stand alone processor like a regular desktop?
Just a warning, I bought a Mac Mini (2009) and wanted it to hook it up to my TV. My TV does not have HDMI or DVI inputs so I bought a Mini DVI to Video adapter from Apple.But I could not get it to work, then I googled for it and it seems this adapter does not work with 2009 Mac's since it does not output an analog signal anymore!
URL
So anyone that wants to hook up his new Mac to an older TV set with the Video adapter, you are warned.I guess i'll have to buy a Mini-DVI to VGA adapter and then a VGA to SVIDEO converter..
I have a fresh install of Windows XP, service pack 2 on a boot camp partition on my macbook (13" first gen aluminum case) and a Apple LED Cinema Display attached to the mini display port.
I can't seem to make the Cinema Display the primary display (the "Use this device as the primary monitor" checkbox is always greyed out in the Display Property Settings tab). I also can't shut the macbook lid and continue to use it closed (with kb, mouse and monitor attached) like I would when booting OSX.
Is there some other way to make the Cinema Display the primary monitor, so I can leave the macbook closed when booting into Windows?
Is there an easy way to cause a connected external monitor to be "disabled?" E.G. I have an iMac connected to an LCD TV (via VGA, spanned, external at 1360x768). If the TV is plugged in, even if it's off, the computer switches to spanning mode. The consequence of this is that, if my preferred setup is to have the external be main, for instance, I essentially have to unplug it from the iMac whenever I don't want to be using it. Even if the external is the 2ary dsplay, it means that the mouse can go off the edge of the screen on one side, and that two of the hot corners are messed up. Is there any utility that could do something like add a "disable external display" item to preferences or the menu bar?
I own a g4 quick silver which has a "formac" flat monitor. This monitor connects straight in to the g4. I have just bought a g5 but it will not connect, I have looked at adaptors but cannot find the right one. Does.
my mac pro desktop was bought roughly in 2009.its running the latest os that this model can run with tiger.the problem used to be intermittent,now it is very hard to get this thing to communicate with the external monitor.the led on the mac shows that its on but it won't chime as it starts up.whenever it did cut on,it would stay on for a moment then a dark tint would scroll over the screen desktop from top to bottom and everything freezes.i then have to turn off the computer from the button.A side note:This computer never functioned properly from day one when i was using it to run my protools music recording DAW.i could barely complete songs as it would run out of cpu and processing power.the computer has 14 gigs of ram,and quad core processing.i took it to apple store for tech support but they found nothing.now i am solely trying to run my serato dj software with it.based on these symptoms,what is wrong with my computer? is it software problem or is it a bad graphics card,bad cpu,is there any parts i can buy to inexpensively overhaul this computer?
The old Mini worked fine with my Westinghouse 24" LCD monitor (HDMI input -connected to Mini via DVI->HDMI cable).The new Mini Server 2010 has HDMI out, so I used a straight-through HDMI cable. The display looks terrible! All of the fonts appear to have a 'shadow' next to them - almost like an old analog VGA with 'interference'.Thinking it could be the cable, I went back to my old Mini's DVI->HDMI cable (and used the new Mini's HDMI->DVI adapter to connect to it). Same results.The Westinghouse monitor's native resolution is 1920x1200. The Mac says that it's configured for 1920x1200.
I want to run my g4 17 inch powerbook connected to an external screen with the lid closed, when i shut it the external screen goes off aswell, I have been told to use an external keyboard etc, I want to use a bluetooth keyboard and mouse. Is there anyway of doing this?
I feel like when i try to hook up my macbook to a monitor with the vga adaptor, it just never works smoothly. i always have to play around with the wires for a while until i have an image on the screen. plug out the usb mouse and keyboard, plug them back in, unplug the adaptor, plug it back in. then finally it works, and this is every time i try to do it. i prefer to to it with my laptop closed, not in dual screen mode. can anyone point me to a simpler process to do this? its getting really annoying
Looking for a keyboard (preferably wireless) and mouse to hook up to my mac that will be connected to a monitor. I also want to use the display for my pc laptop. Will I have to keep registering and unregistering the keyboard and mouse every time I want to switch between my mac and pc? Also does anyone know if I will have any problems with the apple wireless keyboard and logitech mx revolution mouse with both my computers?
I am trying yo plug my NEC EA231WMi into my MBP via DVI and a DVI to mini display port Adaptor and the computer is not recognizing the monitor. It does nothing when I plug the monitor in.
I bought a 22 inch monitor. its a pretty generic brand, but its very high resolution and works great on other computers. i got the vga adapter for my aluminum macbook (i posted in this section because its closer to the 13" mbp). i have an apple keyboard connected to it. i try to use it in clamshell mode and when i press a button on the keyboard to wake it up the screen just flickers as if its trying to adjust the resolution. strangely enough, it works perfect in mirror mode. anyone have an idea?
Did any of you experienced this ? My WiFi slows down or even stops working when external monitor is connected (via the big connector, don't remember it's name, DMI or something like that). Air Rev A, 1.6.
I have a strange problem with a WiFi slowdown when connected to a TV. Here are the specs of the equipment: 2.2 Ghz white macbook, santa rosa, 4 gb ram, purchased January 2008 Panasonic TV connected via HDMI to DVI cable + Apple Mini DVI to DVI connector USB Western Digital harddrive connected to a 500 GB Time Capsule (1st edition, no dual channels) Snow leopard 10.6.1
Before upgrading to snow leopard, I would frequently use the macbook to provide video to the above mentioned TV streamed from a hard drive connected to an imac (connected to the same time capsule). I moved, and upgraded to snow leopard, and haven't tried this until finished setting up my equipment yesterday. I can stream videos to the macbook from this hard drive fine when nothing is connected. However, the moment I plug in the mini-DVI connector, the WiFi drops to a crawl. This applies not only the to air disk but any data from the network (internet, etc.)
A couple of additional notes: Display is set to mirror. Has nothing to do with clamshell mode because the macbook isn't closed. Nothing to do with location/interference- the effect is instantaneous with plugging and unplugging the cable. The base station is actually closer than in my previous setup and is pretty much 20 feet away in direct line of sight. I connect to another external monitor daily at work (vga, again with apple mini dvi to vga adapter)- no issue whatsoever restart did not help. I canceled all time machine backups over the network to limit that as a factor- no effect.
I have a new issue with my Mac Pro (3,1 - 2008), it just popped up (and I don't think it was caused by 10.6.3, I remember this working correctly after it was installed I have two monitors connected via DVI to a flashed XFX 4870. The 4870 has never given me any trouble.In the Energy Saver settings, I usually set the machine to never sleep, and the displays to sleep after 5 minutes. This used to work great, never had any trouble with it, ever. Now, the displays don't go to sleep after 5 minutes, they just stay on with a screensaver.
Recently, my quicktime (with Perian installed) stopped playing AVI files - giving me the whole 'The movie is in a format Quicktime doesn't understand' business. This made no sense to me as AVIs were playing fine previously. Nothing I did could fix the problem. HOWEVER, just today I plugged in an external monitor to test something out; lo and behold, quicktime is playing AVI files just fine again. What's going on?! Has anyone seen this behaviour before?
Just bought a Samsung 2333SW Monitor and plugged it into my Mac Mini. The screen looks like the monitor was dropped (psychedelic) when the desktop is displayed. It worked fine on my 17" Samsung monitor, but not the 23".
I exchanged the monitor, and its not the monitor. I was told its the driver on the Mac. I cannot find any driver online for my Mini through Apple, or even at the Samsung sites.
I purchased a Dell 2209 WA ISP monitor, and connected it to my Macbook Pro via a DVI to DVI connection. My Macbook Pro has a GE FORCE 8600 T graphics card.
The text is quite blurry on the Dell. It is at 1680X1050 native resolution, which is supported by Macbook.
WITHOUT closing the lid, because i like using the touchpad. i know that you can turn the brightness all the way down, but sometimes windows from the main screen randomly open on the other display. and it also slows down performance. i want to turn off the 13" screen as if the lid was closed. that way, the mac doesn't even see it.
I have a MacBook Air (11.6") and a Philips 234EL monitor whose native resolution is 1920 x 1080.
However, when I connect the monitor to the laptop with an Apple HDMI cable and a Moshi Mini DisplayPort to HDMI adapter, the maximum resolution I can get is 1600 x 900.
I'm using a DVI->HDMI cable to connect my Powerbook to my Sony LCD TV. The Sony's native resolution is 1366x768. For some reason my Powerbook doesn't want to switch to this resolution. I can get 1280x720, but this leaves a black border around the images the whole time.
I've tried setting a custom resolution using the trial version of SwitchResX but to no avail. It won't do it. Anybody have any similar experiences and possibly found a fix?
I've been searching for a vertical laptop stand for awhile now, since I use my MacBook Pro and my Dell Inspiron both in clamshell mode and connected to the same monitor. There were some pricy options out there ranging from $40 to $300, and then I found the perfect solution at the thrift store today for $1.50: a napkin holder.I bought one very similar to the one pictured here, and will be sanding it down and painting it black. It works extremely well as a vertical stand, and I'm getting a second for the Dell. Forget overpriced stands and repurpose something
