I plan on replacing my Boot Camp Drive (not partition, separate drive) in my Mac Pro (320GB with Vista 64, NTFS) with a 750 GB drive.
How do I do this? Do I put in the new drive and clone the Boot Camp partition using Disk Utility, and then take the 320gb out of it's slot and put in the 750gb, and Vista will boot fine? Is there anything special I need to do?
Or am I going to have to re-setup everything and reinstall windows?
I'm trying to install Windows 7 and can't get the boot camp assistant to partition my drive. The drive in question is 500GB with over 200GB free space. I want a Windows partition of 35-40GB.On first attempt I kept getting the cannot move files error when trying to partition. I read up on the error online, and most people suggested issues with parallels or needing to use idefrag. I had parallels on my machine at one point, but am not sure if there are any problem folders still hiding somewhere. Any tips on that part?I ran idefrag overnight last night. When I booted the machine up this morning, I launched it again to verify that the disk was defraged. Boot camp still doesn't want to play.
View 8 Replies View RelatedI have a Macbook Pro 17" (MacBookPro2,1 I believe) and it has a busted Superdrive that won't read or burn CDs and DVDs. However, I want to dual boot Windows 7—is this even possible?
I've already tried a bit of a long-winded solution. I used Parallels to install a virtual copy of Windows 7, then booted into that copy, used it and a Windows 7 ISO to make a bootable flash drive, installed rEFIt, and tried to boot from my flash drive. However, that doesn't seem to work as rEFIt just errors out and then prompts you to restart, saying that the firmware refuses to boot, and that support for booting legacy OSes from external drives is rather shaky.
I have two 500GB data drives, one is split in half with Boot Camp getting 250GB.
The Boot Camp drive is starting to fail and needs to be replaced.
I ordered a 1TB drive and my plan is copy all data from the first drive on the 1TB, and then format the working 500GB and put Boot Camp onto it (this time filling the whole drive).
What is the best way to do this?
I'm thinking maybe - run Boot Camp Assistant, set up the partition, then clone the contents on the drive? Is this the best way?
What is the best software to use?
I have loaded XP with boot camp on about 20 IMAC's over the last 6 months at my work. Everything has gone fine until about 1 month ago. When finished instaaling the Mac drivers and when rebooted, in XP, boot camp creates not only the 'C' drive labelled "Boot Camp", but also creates and mounts permemently a 'F' drive on the Windows computer. The 'F' drive is no longer mapable on the XP. I can't have an 'F' drive because other softwatre on the XP need to map a 'F' drive.
Why is it creating an 'F' drive and how do I get it to stop, like the other 20 installs that went fine.
Some details, - yes the Windows partition is very large, usually 500gb
No, I keep it from connecting to the internet - some one said that might be the reason.
not luck finding an answer with search function or google. just covering my bases here. I'm running a Macbook Pro 13" with Windows 7 via Boot Camp. I made my partition 30GB when installing Windows, thinking it would be more than enough for what I needed, especially after reading this. Quote: I opted for 20GB, which left me with just a bit over 16GB to use after installing Windows 7. from: [URL:...] So I figured 30GB would mean I would have up to 26 GB of free space to play with after install. My problem is, I only have 12.5GB free space left over to play with and seemingly my Windows 7 installation is what, 17GB? I'm sort of thinking maybe for whatever reason there's a copy of my Windows 7 installation files somewhere on the partition that didn't get deleted, or all the expanded files used for installation are still sitting somewhere. Before I go ahead and delete the partition and reinstall Windows 7 again, I'd like to know if Windows7 is actually that bloody big and why on the guide I read it says it's only 4GB?
View 7 Replies View Relatedis it possible to have a boot camp drive with windows 7 on a seprate drive on a mac pro?
View 6 Replies View RelatedSorry I know there are ways like using mac drive to do tis but it wouldn't work on my windows. I want to be able to browse my Mac hard drive while using Boot Camp, I have Windows 7 installed on Boot Camp.
Is this possible?
I'm building a custom computer that I would like to run both OSX and Windows 7 on. At the moment I am trying to decide between installing 1 2TB hard drive or 2 1TB hard drives. I would preferably do the latter since I would like each OS to be on its own drive. OSX will be my primary OS. If I go for the 2 drive option they will be 2 seperate drives, not in a RAID config. Getting OSX onto the machine is simple enough for me if not a little roundabout. My main concern is Windows 7. Will bootcamp allow me to install Windows to it's own dedicated drive without having to partition the OSX drive? In my case would I even need to use bootcamp? Would holding down the "alt" key as done with bootcamp detect a second bootable disk even if Windows was not installed through bootcamp?
View 3 Replies View RelatedI am trying to get my Macbook Pro (15" 2.53 GHz, 4GB) to play nicely with Windows 7. To get a valid copy of Windows I got in on the Ultimate Steal program last year. For those who don't know what it is, basically if you're a student you could get Win7 Pro Upgrade on the cheap. Before this I didn't have any copy of Windows on my laptop. I had to go through a huge pain in the ass process of installing XP 32-bit > Vista 32-bit > Vista 64-bit > and then upgrade that to Win7. I finally had a 75GB partition of Win7 64-bit installed, when booting up holding down Option I got to select either the Macintosh HD or Windows so everything's rosey.
I wanted to do some virtualization so I didn't have to reboot all the time so I grabbed an eval copy of VMWare Fusion. I kept getting an error about not being able to load the BootCamp partition, getting an error of Resource Busy. When I look at the partition in Disk Utililty the name of it is disk0s2 instead of BootCamp like it used to on my old Macbook. Trying to mount the mount fails and for some reason the partition shows as exFt. Going back into Windows show that it is in fact partitioned as NTFS.
Well not wanting to go through the same install hell that I did before I used Windows built-in functionality to create a system image as well as created a system restore disk. I blew away the bootcamp partition and launched Boot Camp Assistant, recreated the partition and stuck in the System Restore disk. Boot Camp Assistant restarted to install the OS and everything seemed to go well. I can no boot into Win7 and Mac but the partition on the Mac side still shows as disk0s2 and exFat. It *is* now mountable but it shows that the drive is completely empty (107 gb free, 1.8mb used). Another weird issue, the partition isn't 107gb, it's 80gb. And there is definitely more than 1.8mb used. Obviously VMWare still doesn't like this and I'm just stuck.
In retrospect, I should have ignored it when Apple Software Update told me about the Boot Camp 3.2 upgrade for my 2006 Mac Pro running x64 Win 7 ultimate. When I ran it, it overwrote my blue tooth driver and my keyboard stopped working. Thanks for the folks at Mac Rumors forums, I was able to go through the procedure to get it working again, and I also had to update the video driver (again) from ATI for my 3800.
So then I decide to reboot into MacOS and discover that my icon for selecting the boot disk was gone, not to mention any directory or programs in the start menu. This happen to anyone else? Do I have to downgrade to 3.1 or does anyone have a recommendation to get 3.2 working?
My OSX partition shows up fine in my Bootcamped Windows 7 x64, and I can read/write to it fine. My external, a Western Digital 1tb drive formated HFS+, is connected thru firewire, and it doesn't seem to mount or show up at all.
View 3 Replies View RelatedIs it possible to install windows 7 on my macbook from a removable hard drive using boot camp? How would I do this?
Info:
MacBook, iOS 5.1
Running a 2010 MBP Core i5 2.4GHz. I had Windows 7 originally installed. Gave me wireless problems and I gave up. Erased the partition. Installed Windows XP and everything was fine.
I got a new copy of W7 Professional x64. I installed it "over" the existing XP, though it erased the partition anyways (I don't care about that).The new 7 install has been giving me the same wireless problems. I downloaded and installed the Broadcom driver. Gave me a BSOD and restarted the computer. Now I have a BSOD on start up, too. On the OSX side of things, it no longer shows any Boot Camp hard drive. It doesn't recognize it at all. Though when I hold the option key on boot, it still shows the Windows install.
1. How do I fix the BSOD problem? (All caused by installing the driver)
2. Where the heck is the Boot Camp hard drive/partition?
I recently got rid of a partition I had made for bootcamp since I never use it, and would rather have the space back. I deleted the partition through disc utility, and then through the partition tab, tried to get back that space by dragging down the tab to restore the space originally set for the partition. When I go to apply this change, it notifies that my hard drive will be re-sized. I accept and then a few minutes later it comes back with the error "Partition failed with the error: Filesystem verify or repair failed" Does anybody know how I can restore this space successfully back into my main hard drive? I've attached some screenshots
View 10 Replies View RelatedIn my attempt to install Windows XP via Boot Camp, I accidentally inserted an SP1 disc instead of the SP2 disc that I have. The installation proceeded to the point where it does for most who attempt this: the screen where you are prompted to press ENTER. I could not proceed and therefore restarted the iMac and held down the mouse button upon start-up to remove the CD.
HERE IS THE PROBLEM:I can not boot into OS X because the keyboard shortcuts (those that might allow me to select which partition to boot from and/or reset PRAM) seem to be disabled. Instead, a reboot always ends at a black screen with a blinking DOS-esque cursor, or the prompt: "No bootable device -- insert boot disk and press any key."
I have attempted inserting my SP2 disc at this point, to no avail. My keyboard seems to be disabled, as if the SP1 install proceeded just enough to establish itself as the boot drive without drivers for the keyboard. I've tried using all 3 USB ports, disconnecting other USB devices. Oddly, my bluetooth mouse works to eject the CD on reboot...
I've been hearing good things about the Spinpoint Drives and the 750GB ones are coming down in price.Here is my current setup1 - 500MB Drive - Leopard2 - 320MB Drive - Vista 643 - 500MB Drive - FAT32 (Shared, Irrelevant)I plan on replacing drives 1 and 2 with 750GB Spinpoint drives.My question is, can I boot off of the Leopard dvd and put in Drive 1 and NewDrive1 and just clone it, and do the same for Drive2 and NewDrive2 and clone it? And then go into Leopard and resize the HFS partition, and go into Vista and resize the NTFS partition?
View 2 Replies View RelatedI have an '08 Octo 2.8.
I created a Boot Camp Partition (an entire drive, actually) and installed XP. The install went off without a hitch ... Except, having rebooted to Mac OS X (10.6.1) there is no way to boot Windows again. Going to Preferences->Boot Disk shows no Book Camp bootable drive.
This is the 1st time i got a Mac , i bought a black Macbook 2.4GHz some days ago .
I installed Windows Vista Ultimate using Boot Camp , and all went smoothly .
Only 1 prob is when restarting , i have to wait too long for the Windows to log on , i think about 1min with the black screen.
And if i want to boot in Mac OS , i have to push down the D button or the Alt, it takes quite a long time too .
So do you guys have any solution to this problem ? I want to get rid of the waiting time, way too much.
And do you know how to make my Macbook jump right in the choosing section when it starts ? ( so that i dont have to push down any button when it starts )
I have been trying to install Windows 7 (yes, legit copy) to my Macbook Pro the whole day, but I keep on getting this error message saying "Press any key to boot from cd or dvd . . . ."
When I press any key on the keyboard, nothing happens. I know this copy works because I've tried this on VMWare 3. (I'm going to Boot Camp of BIOSHOCK!)
What I've Tried:
Deleted partition, recreate partition and choose the Windows 7 disk as startup disk.
Well I installed Vista Ultimate using boot camp on my 27 inch iMac using 10.6.2 and now I can't get it to boot in OSX. I tried holding the command key when rebooting but it just goes into the windows part. Looks like windows took over. Does anybody know how I can get it to boot in Leopard?
View 3 Replies View RelatedHave the new 15" MBP with i7 Processor. I had another MBP with a 7200RPM drive and installed drive in the new i7 Mac. Computer was working fine until I installed Windows via Boot Camp. I can't boot to the Mac Partition any more, the partition is there but when you try to boot to it you just see the Apple logo and NO circle. I cannot boot to the install CDs or a bootable external drive. I target disk mode the computer and used another computer to boot using the drive in the i7 unit and it's fine and I can see all the information. I tried booting the i7 into single user mode and saw the following message:
efiboot loaded from device: Acpi(PNP0A03,0)/Pci(1|1)/Ata(Primary,Master)/HD(Part 2,Sig********-****-****-****-************)
boot file path: SystemLibraryCoreServicesoot.efi
.Loading 'mach_kernel'...
................................................................................
Over the last half hour or so, I've heard a couple intermittent click type sounds coming from my Mac Pro, when this happens, the apps I'm accessing start beach balling for maybe 10 seconds or so and then finally go back to normal. It certainly sounds like a hard drive noise, and the fact that it causes my apps to freeze up leads me to believe it's my boot drive (I have the standard 250GB drive that came with the system as my boot drive with all my apps installed, and then I have two 1TB drives in a mirrored RAID for my home directory)
The SMART status on all 3 drives check out fine, so I don't know of a decent way to pinpoint for sure which drive it is, but I want to nip this in the bud. Does anyone have any suggestions on if I can do anything else to check? It's only happened twice so far and it's been a while since the last time it happened, but I don't want to wait until it's too late. Also, what's the best way to replace my boot drive without having to do a reinstall of the OS? I've never had to do this before on a Mac...
I just installed Windows XP to a Boot Camp Partition on my MBP. However, rebooting is a hassle and naturally I want to avoid doing such as often as possible. I think running Parallels Desktop would suit my needs quite well. But here's the catch: I want to be able to use one partition to serve both of those needs. In other words I want have the option of booting through both Boot Camp or Parallels.
How would I go about doing this? I already have a XP installed via Boot Camp. So if there is a method where I don't have to reinstall, great, but I am fine with deleting stuff.
I just purchased a new iMac (2.66 c2d & 4gb of ram), Parallels 4, and Windows XP. I would like to get great performance whenever I use Windows XP and would like to know which installation procedure would help accomplish that.
Would Parallels provide me with a better user experience by installing Windows directly via Parallels OR by having Parallels utilizing a Boot Camp Partition? Which is better and why? Also, how much memory should I allocate to Parallels/Windows XP?
Last night I installed VMWare Fusion and Windows 7 on my Unibody MBP running SL. When I use Fusion, my computer slows to a crawl. I spent a few hours getting Windows set up and installing software last night.
I would like to try using Boot Camp instead, but do not want to lose all of the software and files that I have installed. Is it possible to set up Boot Camp, and keep the same Windows setup?
hi! i'm planning to install windows 7 64-bit in my mbp, problem is i looked at the requirements needed and it stated that i needed boot camp update 3.1. i checked my boot camp version and it stated that i had 3.0.1, tried using software update, but states that i had no updates available. what should i do? and what else do i have to keep in mind while installing windows using boot camp. thanks in advance!
View 1 Replies View RelatedI use to be able to select the vista partition to restart into from the configuration pages in leopard on my macbook pro, but now my bootcamp partition is missing. I have to hold the option button to manually select the windows partition and then load into windows. Some setting somewhere must be lost. Does anyone know how to restore it?
View 2 Replies View RelatedThis is my first post here... even though, I've read a lot of the things on this forum, but never decided to post a question 'til now... now that i bought a macbook pro that is.
Actually I have some sort of annoyance with boot camp. It works as it's intended (with windows 7, which is a miracle, because everyone complains about that combination). But whenever I boot up and press "alt" to select the hard drive i want to boot, it always shows Windows. Can i change it for something else? and, how can I do it? Both of my partitions have names of their own... they're not generic... but still, they are not working, what can I do??
Would have checked this myself but I haven't gotten around to installing Boot Camp 3.1 yet.
Anyone with a uMBP try to see if Boot Camp 3.1 allows the keyboard light to completely shut off in Windows 7?
I described it more here.
