I recently got a PowerMac G4. When I viewed it Everything was working. Upon me hooking it back up I noticed It was not getting any picture. The Monitor was brand new so I did not figure it to be broken I checked the monitor on another computer and it worked great. From what I understand this is a common internal problem on the G4.
View 5 Replies
I have a 15" unibody MBP bought in Nov '08.
Had been using the Mini Displayport > DVI adapter just fine with both HDTV and Dell monitor, BUT then all output has stopped completely!
No monitor is detected by the laptop (although the display does blink blue, as if it had detected it), tried different cables, different displays, using the Displayport firmware update, speaking to Apple, deleting the com.apple..plist files, etc
Edit: it also doesn't work in XP on Bootcamp
I have a G3 iBook and just the other day the display stopped working. There were no signs of the display going bad, it's just went. Am I able to boot the iBook via Target Disk Mode on my PowerBook and run the iBook Hardware Test CD on it? Also, can I reboot my PowerBook and choose the iBook as the startup volume?
I know how to do Target Disk Mode but the latter I'm not sure about.
just came home from Apple Store today with new computer and superdrive, which is not showing up when plugged in. When I put a CD in it reads it for a few seconds then spits it out. I am on the road so getting to an Apple Store will not be easy for the next week.
Info:
MacBook Air (11-inch, Mid 2012), Mac OS X (10.7.4)
I have a 15" unibody MBP bought in Nov '08.
Had been using the Mini Displayport > DVI adapter just fine with both HDTV and Dell monitor, BUT then all output has stopped completely!
No monitor is detected by the laptop (although the display does blink blue, as if it had detected it), tried different cables, different displays, using the Displayport firmware update, speaking to Apple, deleting the com.apple..plist files, etc
Edit: it also doesn't work in XP on Bootcamp!!!?
None have worked even a bit!.. Also read lots of forum posts of similar problems, but I can't find a solution that works!
I have a 27" iMac and I'm using Samsung SyncMaster SA850 as a second monitor (connected via a display Port cable with a mini Display Port adapter). Everything worked fine until yesterday - the Samsung screen turned black and now it only works with max resolution 1280 x 1024 (native is 2440x1440). I think I upgraded Lion 10.7.2 to 10.7.3 (I don't remember for sure though). When I connect the monitor to an iMac with 10.7.2 everything works fine. And another iMac with 10.7.3 has the same problem as me.
Info:
iMac, Mac OS X (10.7.3)
I hooked my Macbook mini-display port up to my new Sony 32" TV and it worked fine for a month or so, but then it stopped working. Now when I plug it in the TV says there is "no signal" and the laptop doesn't detect the display. Nothing happens when I plug it in. I have tried two different HDMI chords, but only one mini display chord.
View 1 Replies View RelatedI have a macbook pro from fall of 2007. So far it has worked perfectly and I've used it with an LG full hd LCD for about 1,5 years. I use a regular DVI - HDMI cable.About a month back it suddenly stopped working. The TV just tells me "No signal".I didn't change any settings or anything. The computer still recognizes when something is plugged in as the screen flicks blue and the displays icon in the menu bar lists the TV with correct model and resolution. And if I have spaces turned on it changes from 4 to 8 "screens".
I have tried everything from rebooting the computer to resetting P-RAM.
I got a new cable, no difference. However when I tried the TV with my friends MBP, it worked. So the problem is definetly in my computer, not in the TV or cable.My OS X is Version 10.5.8 Leopard.
I have a November 2009 27'' i5 iMac and a 2010 Macbook Pro 15'' i7. After installing the iMac's Target Display Update 1.0 and 10.6.4, I'm no longer able to connect the MBP to my iMac. When I plug in my mini displayport cable, the iMac's screen goes black for a few seconds, then the MBP's screen flashes blue for a second or two, and then back to normal, and finally, the iMac's screen goes blue for 5 seconds or so, and then back to the desktop.
View 2 Replies View Relatedtried vol up and down in preferences..nothing the only output is headphones it says
View 1 Replies View RelatedMy internal speakers in my PowerPC G4 just magically stopped working! It recognizes them in system preferences. And yes, the volume is up. I dont know what happened. The headphones do work. I havent tested external speakers yet, but that's next on the list.
View 5 Replies View RelatedI installed 10.5.7 yesterday. Immediately after the installation was complete, my Apple bluetooth keyboard stopped working. Went into Bluetooth system settings, and it said that there was no bluetooth hardware found... (it's built into the machine!!)...
Also, every time I start iTunes, it gives some weird error about Adobe Flash player. I'm not at home now so I don't have the exact wording of the error with me, sorry...
Up until recently, F1 - F5 have been Brightness and Volume controls, as they have been since I got the thing. I go to use the Volume, and it doesn't work. I then try the Brightness, and it doesn't work. F6 - F12 all work just fine, which leads me to believe that iBook had a brain fart.
My volume balance has always altered itself. Balancing itself out of one speaker left or right as it so chooses. I know it's smart, but now it's just screwing with me. Settings go and change on their own, dock icons have switched, but this one has stumped me. How do I get those hardware function keys back to doing what they're there to do?
Also, I tried it with an App called Rowmote, that lets you control your Mac from your iPhone, with Apple Remote-like control, and the volume won't change using that either. Another symptom is that sometimes it makes clicking sounds, as if it were changing slowly and glitchy (which it did click sometimes anyhow) when using the Volume slider in the menu bar.
No, the options in System Preferences is not checked to use them as FN. Any ideas?
I am here today looking for guidance with my ibook. I recently updated the software from 10.3 to 10.4. The wireless was working fine on 10.3. Then when I upgraded it it just stopped working. Now it says there is no airport card installed. I need to fix it because I need it for school!
View 2 Replies View RelatedThe trackpad on my iBook G4 1.44ghz stopped working this morning! At first it went stuttery. I temporarily solved this by plugging in a mouse- without using the mouse itself, this seemed to make the trackpad responsive again.
After letting the iBook go to sleep, the trackpad doesn't work at all; nothing I do seems to make it respond. I've tried resetting the PRAM and NVRAM, but this hasn't done anything.
Is there anything else I can do, short of buying a new trackpad?
Last week, my airport connection suddenly stopped working (and I mean JUST as I was working on it, it started failing). It would connect to the network fine, but it could not communicate with the router through DHCP and even with a static IP, it could not transfer any network data. I put in my brother's working airport card, and it worked, so I ordered a refurbished airport card from ifixit.com. I put that in today, and it is showing the same symptoms of my old card. I don't have my brother's PowerBook to test his card again, so I don't know what to do.
View 1 Replies View RelatedJust a piece of info for those considering driving a 30 inch Monitor with the Mini: The mini-display port to Dual Link DVI adapter Apple is offering is not working. There are some other forums discussing this problem with the unibody Macbook pro. I've been using mine since Dec. At irregular intervals the screen becomes blurry (weird double lines all over), and the only thing that works is plugging back in or (more harmless if you have multiple projects up and don't want them to be scattered all over the screen) Control-Shift-Eject to put the display to sleep, then wake it back up after a few seconds with mouse or keyboard. This can be very annoying as sometimes one has to repeat it multiple times. Apple is aware of the problem, but has not come forward with a solution. I just don't want you guys to be disappointed in your new Mini with a capable graphics card...
View 19 Replies View RelatedI have an old iMac G4 and I was wondering if I could just use the screen somehow since I don't need to use it as a computer? Could I use it like a TV to play xbox or something?
View 6 Replies View RelatedI've been using my black macbook for several years with both my Apple Cinema Display and Panasonic TV with the Apple mini-dvi to dvi adapter, but today when I tried to hook my macbook up with the tv it didn't work. The Tv just showed a black picture and nothing happend when I un- and replugged the cable. I tried it on my ACD as well and the colors wasn't right on it. Some colors wasn't showing, eg red. Green and blue was OK. I'm suspecting the adapter to be the problem, 'cause I've tried everything (also in preferences) and been using this method for years! Any thoughts on the problem? Should I buy a new adapter or try something else?
Connection methods;
TV = mini-dvi to dvi, and dvi to hdmi
ACD = mini-dvi to dvi and dvi directly to the ACD
I recently replaced the video card on my G4 and now the USB ports on the back of my apple studio display are no longer functioning, but the monitor itself is functioning just fine. The USB ports on the tower are functioning normally.
2002 Quicksilver 933mhz G4
1.5gb RAM
17" Apple Studio Display via ADC connection
(New card) ATI Radeon Pro 9000 64mb AGP ADC/DVI
I have a MacBook Pro 13 for portability to my classes at the university and a Dell 2209WA as an external monitor. One of the few good IPS monitors I could find around for cheap.
The monitor works fine in mirror mode with the MacBook Pro, but as an external display only it does not work. It attempts to wake up and then you see power savings mode again and the screen goes black as if there was no connection. Not sure what exactly the problem here is. Drivers?
The monitor works great with a Mac Mini I have and it works great in mirror but not in external display mode(the lid of the MacBook Pro closed). Anybody know of this issue? The cable is good and the MacBook Pro is not that old(a few weeks).
I have a 14'' iBook and recently bought an LG 19'' Widescreen monitor. I am testing a Dell 17'' on it right now before I open the LG one, but my problem is that the same screen shows on my ibook and the external. This isn't what I want. I have read you are supposed to be able to close the laptop and then it shifts to the external display but this is not working for me.
This is my goal:
Use my bluetooth keyboard full time
Have my ibook closed at all times
Have my external as my main display
How do I make this work?
My friend has a PowerBook G4 and he wants to connect it with an external 20" Apple Cinema display. His friend told him it was not possible to connect it, but I am not certain if this information is correct. He asked me to help advise him on this, but unfortunately I don't know enough about Apple hardware to give him the information he is looking for. I am wondering if anyone happens to know the answer on this.
View 7 Replies View Relatedirst off, according to mac tracker the Powerbook I have is the Powerbook G4 15 inch FW-800. I am running Mac OS X Leopard 10.5.6
Alright. About one week ago, I hooked up the powerbook to a 19 inch external LCD monitor with a DVI to VGA convertor, and all was well. It found my supported resolution and everything, worked straight away, etc.
Fast forward to today, at about 2pm (4 hours ago) I was using the computer and everything was working fine, but I had left it on for a few days so I shut it off when I was about to take a nap. I wake up from said nap about 20 minutes ago, turn on my Mac and my external display is only showing up at 800x600. I have no idea how this could have happened. This would not be an issue if my monitor's native resolution of 1440x900 were on the massive list of resolutions to chose from, but alas it is not.
I read the thread about how to pivot your screen over in another section but it didn't address what to do when it goes wrong. And it did...very wrong. I'm running a Powerbook G4 Titanium 15" laptop with Tiger OsX 10.4.11 and I hooked an external monitor to it. I was playing around with the settings and saw the rotation feature, which wasn't available until I attached the external monitor. As soon as I clicked on 90 degrees, both the main screen and the external fritzed out. I could vaguely see things through the haze on the main screen but the whole thing had stopped responding to all mouse and keypad commands. Eventually the only thing I could do to regain control was a hard shut off with the power button and unplug the external. After that the main screen booted up just fine but the moment I hook up the external again they go blue screen of death on me and I can't see what I'm doing to undo what I did!! I tried hitting the manual reset on the screen itself, which I didn't really think would work but hey, desperate times...
After some research on the internet I found out that, contrary to what the other thread says, not all Tiger enabled computers can run the rotation function, apparently because the scan rate, or something like that is too low. Which is why the option was disabled when only the main screen was running. Nice to know and would have been good to know sooner but what I need help with now is HOW DO I FIX THIS MESS?!!!! Some sites mentioned archiving (I'm moderately computer savvy but I'm not totally sure I know how to do that) and some have mentioned the boot disk, which I have but I want to make sure I know what will happen if I do that. I've backed up my files just in case. Will it erase the programs I've installed or just my settings? Or is it much simpler and is there something in the utilities I can mess with that will reset stuff?
So I had a recently purchased 17" BTO with the 7200RPM drive that worked great, but with one issue - the display would have horizontal scan lines and black out occasionally. So I called up Apple and eventually managed to get a cross-ship set up(they let me hold on to my current unit, charge my credit card and send me a second brand new 17" unit as a replacement,and then refund me for the second 17" after I send back the defective unit).
Anyway, the replacement unit looks great, but with one issue - there's a very small light dent on the bottom panel(maybe about the size of a dime). I was annoyed but don't think this is worth having to exchange, since I could probably just unscrew the panel and pop it back into place.
However, what really got to me was the fact that my replacement unit was slightly louder than my original - my original is so silent that I can't even tell it's on. However, with my replacement unit, I can hear the hard drive spinning, which is slightly annoying.
Anyway, I proceeded to restore from a time machine backup and test my replacement unit when I noticed that it would occasionally get the hard drive click + beep + freeze issue that many others who have the 7200 RPM drive seem to be facing. It's extremely annoying, and more importantly I miss the complete silence of my older unit.
My question is, while I'm still in possession of both units(which both have the exact same specs, same 7200 RPM drive, etc.), should I simply just open both up and take the silent(good) hard drive from my old unit and put it into my new one?
The click+beep freeze issue is really pissing me off, and my old unit didn't suffer from it - it's just this replacement one(doesn't make any sense).Anyway, would notice if I switched the hard drive? Would I get screwed somehow? Do they keep track of the hard drive serials or something?
I really don't want to go through the pain of sending this back, especially considering that a LOT of people are suffering from this issue, and I don't want to end up with another defective drive. I'm sick and tired of games and just want a computer that WORKS.
I have a MacBook Pro "Core i7" 2.7 13" Early 2011.
I use and external display Philips 220C1SW
Recently my mac won't recognize the Philips brand anymore and use instead a generic display resolution, which is wrong.
Info:
MacBook Pro, OS X Mountain Lion (10.8.5)
I just bought a brand new charger and it stopped working after about the third charging cycle. The light just simply doesn't go on and the computer doesn't read anything.
Weird thing though is that my old charger did the same thing at the end (although if you jiggled the connection it worked)? Could it be my computer? Although I tested the charger on another computer and it didn't work either. and a different charger on my computer worked.
Is this common for the new chargers that there are lemons once in a while?
Could it be because I left the plastic over the charger to prevent scratches?
Will apple exchange it for a new one or are they gonna give me a problem cause I really don't think this should have happened.
Just got my Creative Inspire T12s in. I hooked them up to my MBP and powered them up. The left speaker isn't working. I checked the L/R balance in iTunes and everything looks fine. There is an audio cable that connects to the MBP, and a cable that connects from the left speaker to the right speaker.
View 8 Replies View RelatedI have a new 17" uMBP that I've owned for just a few days. I noticed yesterday that while I watching a video that i had strange green/red lines (horizontal) appear across the screen and flash/flicker. I freaked out and closed the lid, putting the unit into sleep, and opened it again and it all stopped. Today, I was using it again as usual, on firefox/etc. when it started happening again. Horizontal lines across the screen, the entire display flickering and screwing up and finally going black. I don't know what's going on, but I know this definitely isn't supposed to happen. I took a screenshot during the flickering/lines/etc but the screenshot came out perfectly fine unfortunately. I'll try and get it on camera next time.
I have all software updates installed. I tried resetting PRAM. The flickering I'm talking about isn't minor, it's actually absolutely horrendous and the computer is completely unusable when it's going on. It ultimately leads to a black screen. Anyway, this is all on the 9400, and I have no idea what's going on but I definitely know this isn't supposed to happen. UPDATE: I booted into Windows via bootcamp and it STILL happens. I also connected it to an external display(which works perfect), which leads me to believe that it's 100% a hardware issue. I'm taking it back to the apple store, enough said. This is my first Mac and I can say I'm definitely not happy to be having such issues with a $2500 machine.
