I currently have 4 x 512 PC3200 installed. Is it possible to remove 2 of the modules and replace them with 2 1gig PC5300? I remember my old G4 used pc100 and I was able to upgrade with PC133. Not sure if the same concept applies here.
View 2 RepliesDoes anyone know of any compadible Dual Layer DVD that work with a PPC G5 Dual 1.87ghz?I tried memorex DVD+R DL and it kept on spiting out the disk
View 1 Replies View RelatedI am looking for a tear down guide for my 4 core power mac. I need some instructions on how to remove the CPU's since I bought this for $100 and found the part for $250.
View 2 Replies View RelatedI've got a g5 2.5 dual mother replace to a 1.8 dual g5 tower, nothing happen except all the fans, did anyone know is it work, or my 2.5 mother board also dead?
Info:
PowerMac, Mac OS X (10.4.11)
I have a Powermac Dual G5 @2.0ghz, with 8gbs of ram, and 2 1tb drives running the latest version of 10.5. The problem I have is that I have 4 LCD monitors that I was using with my PC. I swapped that out with my mac, and while I am no novice, I didnt take into account that I cant just put any AGP and PCI video card into the system. What I need to know is if I can use two PCI video cards both with Dual Monitor outputs, and if so, which cards should I buy, and where? I found some video cards on ebay that are PCI, and it is quartz extreme compatible, but I am unable to use it with the AGP card already installed. The person selling the cards was unable to answer whether or not two of those cards could be used together. I only have about 75 per card to spend. Please help, I cant go on using this awesome machine with only one 19inch LCD. and I cant afford to buy new monitors
View 1 Replies View RelatedI had a weird issue this morning. I started computer and it did not make the chime sound, it didn't do anything at all. I disconnected it from the extension cord as well as all the peripherals attached to it and nothing. I tried a different start up disk and again there wasn't a sound. Then i unplugged it and reset the SMU on the mother board and air sprayed the computer to remove all dust. Then plugged it back and it came back on.
Information:
Power Mac G5 Dual 1.8
Mac OS X (10.4.11)
I scanned the posts and didn't see this question, but honestly I didn't read all 20K + messages.I bought in late 2005 a dual 2.3 G5, about 6 months before the Mac/Windows combination came out. Does anyone know if I can upgrade or is it too costly to do so compared to buying a new machine.
Information:
PowerPC G5 Dual 2.3
Mac OS X (10.4.11)
Will OS 10.5 run on my Dual 2 GHz PPC G5? It has 512 SDRAM.
Information:
G5
Mac OS X (10.3.9)
I am posting this here as well as in the Logic area, to try to get some help. I am desperate, as i can't work. In Logic Pro 7, I can't click anything in the right pane of the bounce dialog box. I CAN select PCM, Mp3 etc. on the left, but get no response from the mouse when trying to change the sample rate, interleave, dithering etc. on the right. I also can't click the flip-box to select different packages in the Loop Browser. I haven't noticed this happening in other applications. DOES ANYONE READING THIS KNOW HOW I CAN GET SOME HELP FROM APPLE? I am told i can't even buy apple care because my computer is too old. I don't know what to do. Tried trashing prefs. Not running any failed audio units. Nothing new in software update. Don't really know what else to do.
View 7 Replies View RelatedI'm working on a Mac Dual g4 desktop computer at work, and it won't turn on. We've always had troubles with a sticky button, but it usually comes on after a couple tries. Just before I had this problem, we had tried to switch to an older startup, which gave us trouble, so we went to restart the computer and that didn't work either. Have been reading through discussion posts etc to troubleshoot, tried switching out the power cord and PMU restart, no luck. Unfortunately don't have a keyboard with a power button... What now?
Info:
PowerMac, Mac OS X (10.4.11)
I cannot seem to get my second hard disk (lower drive bay, B) out of the machine.
I've disconnected the data and power cables from the drive, lifted the B drive swing tab out of the way...but no matter what that drive seems to be wedged in there pretty good.
Information:
Dual G5, and stuff.
Mac OS X (10.4.9)
I have been searching the net for 2 straight hours now. I cant get my g5 to read dual layer dvd +r disks. Not write but read. My ibook g4 can just fine. My drive is a pioneer dvr-107d. I keep reading about updating the firmware but for the life of me i cant firmware anywhere.
Information:
powermac g5 dual 1.8
Mac OS X (10.4.10)
Is there a way to get a USB startup on the dual 1.8ghz G5?My macbook enables USB boot obviously but my ppc does not support it
View 5 Replies View RelatedI have a question about the Dual-Proc MacPro's power management:
If you are only running one or two applications, using one or two cores, is the power management smart enough to put one of the processors to sleep, or into a low-power mode?
Is there an upgrade beyond 10.4.11 to Leopard 10.5 that doesn't require an intel-based mac. I bought Snow Leopard 10.6.3 and it tells me that I need an intel based mac. Will 10.5 leopard work?
Info:
Power Mac G5 (Late 2005), Mac OS X (10.4.11), Dual GHz Power Pc
I just bought a Dual 1,25 Powermac. Included were the original restore discs. I've installed the OS 9 package, but when I try to boot from OS 9, I get the flashing question mark on startup.
Info:
PowerMac, Mac OS 9.2.x, Dual 1.25 with Firewire 400
Will the stock Mac Pro video card: NVIDIA GeForce 7300 GT, work in a PowerMac G5 Duallie 2.0 (mid 2004 model) with the pci-x slots? would a Cube G4 Rage 128 video card work in thePM G5? (I bought a G5 without a video card and I need to test it and find a cheap video card for it).
Information:
17" MacBook Pro 2.16/120/2gb ram
Mac OS X (10.4.10)
Mac Pro 2.66, 250 & 80gb hdd, 2 DL-SD, 7gn ram, APX & BT
I have a PowerMac G5 single processor. I went out to the Apple store and they sold me this new graphics card.(PCI x) They insured me that it would work on my g5 and will work with dual monitors. Well thats not the case today. it didnt fit in my computer and was wondering how would i get a dual monitor on a powermac G5
Information:
Mac OS X (10.3.8)
I have a G5 Power PC with Dual Ghz 2.5 processors. I have two 250 GB hard drives, my primary drive has 45 GB available and my secondary (storage drive) has 10 GB left.
My problem is that I have 6.5 GB of installed and recognized RAM, and yet I constantly hear my hard drive spinning up, as though the OS is using virtual RAM off of my hard drive(s), and ignoring my plentiful system RAM.
This happens when launching every application - big or small - and even surfing the internet. I open Activity Monitor and see that my Virtual memory is 7.2 when idle and grows to 8.5 with a couple of programs open. My page in/out is 48919/0.
This "spin up" sound happens all of the time, whether I am working on something or not, but particularly when I launch programs. No background programs (such as a virus scanner) are installed or running.
So my question is this: Is there any way that I can adjust OS X (latest version) so that it strictly reads my system RAM first before going to my drive? Some setting somewhere? I thought that OS X (as in all computers) only went to the hard drive's VM when it ran out of System RAM. Am I missing something?
Information:
Dual 2.5 GHz PowerPC G5 and iMac G4 800MHz w/ 1 GB RAM
Mac OS X (10.4.10)
G5 Dual 2.5 Ghz 6.5 GB DDR SDRAM, 2 - 250 GB HDs Logic studio 8 and Adobe CS3 Suite,.
A G5 PPC Dual 2GHz that I am working on freelance for a client apppears only to have 4 RAM slots - could this be the case? I thought that from the 1st Generation onwards all G5s contained 8 slots.
Information:
G5 Dual 2GHz PPC
Mac OS X (10.4.10)
FCS 2 - FCP 6.01, Motion 3.0.1, DVDSP 4.2.0
What is the best graphics cad for a dual processor 2.5 ghz power mac g5
View 2 Replies View RelatedI am about to sell my Dual 1.8Ghz G5 Power Mac. I bought this from somebody used, and it came with Leopard on it.How can I erase everything on it? I am used to a dell where I just pressed two buttons and it just put a clean copy of XP on. Do Macs require discsI wasn't given a disc when I purchased the Mac, so I sure hope not!
View 2 Replies View RelatedI am thinking of buying a PCI Express Power Mac G5 to run PPC apps.
It seems I should not buy a quad because of leaking.
Are the dual core reliable?
I have Dual 1.8 GHZ Power PC G5 with 1.5 GB DDR SDRAM, with OSX version 10.4.11.My computer has been getting increasingly crazy over the past couples weeks. I'm even having trouble typing this because the screen occasionally "flashes" or "jumps" when I'm in the middle of a task.I noticed the problem first when I would make a new folder. After an untitled folder was made, when I would try to give the folder a new name, the screen "jumped" and I would have to try several times before I could complete the task.
View 3 Replies View RelatedI have a Dual 1.8ghz G5 with 6 gig of Ram and wish to upgrade the Graphics Card. Can anyone tell me a decent card that would improve my system and that would be compatible with the machine. I currently have a 64mb card installed.
Info:
PowerMac, Mac OS X (10.5.8)
I have a Power Mac G5 Dual 2.3 running 10.5.8, I understand that I can not upgrade to Lion, so what will happen to my Mobile me, which I can not live with out? Also will I be able to get Icloud to work?
Info:
PowerMac, Mac OS X (10.5.8), Can I get ICloud to work
Is it possible to update my Dual 2GHz PowerPC G5 to an Intel or other processor? Of course, I'm finding that my machine is not being supported by software developers anymore?I'm running 10.5.8 on my Power Mac (June 2004).
Info:
PowerMac, Mac OS X (10.5.8)
My Power Mac Dual G5 will not recognize my GeForce 6600 LR2A22 Video Card. I have it plugged into the VGA plug. The computer sounds like it starts up fine (chimes, DVD drive runs, hard drive runs), but does not show video. I have tried a new Battery?I have tried the PRAM tricke (did have two chimes)I have tried unplugging hard drive?Is this a video card issue (says its a brand new working card from ebay)Tried on multiple VGA monitors.
Info:
PowerMac
I have a 2003 model 1.8 GHz G5. The original SuperDrive still works fine but I have been looking into an internal Dual Layer DVD-R as they continue to come down in price. Are there specific specifications or brands/models I need to look for to ensure OSX compatibility or to support burning from iTunes and the Finder?
Information:
Power Macintosh G5, iBook G4
Mac OS X (10.4.10)
I am looking to get another mac to do some basic video editing and encoding. All the editing is going to be done in the mpeg4 format and once the video has been edited I am going to encode the video into H.264. My question is which will be better A Power Mac Dual 1.8Ghz G5 or a Mac Mini Core 2 Duo?
I am looking for stable set up that can handle encoding video for a few hours at a time. I am leaning towards the Power Mac Dual G5 because of how much more cooling it has however that said a Mac Mini with a Core 2 Duo running at 1.66 Ghz would also probabley work well.
