The firewire port on the front of my machine is bad. I can't transfer any kind of data using it. The port on the back as well as all USB ports work fine. Would this need a complete motherboard replacement? Would it even be worth doing? Could I build a dual processing machine or buy one cheaper?
Information:
G5
Mac OS X (10.4.4)
My front firewire 400 and 800 ports abruptly quit working. THe backs work fine. I've tried two different video cameras and an external hard drive and according to system profiler none are recognized and none are accessible.
I have a 2006 Mac Pro and recently my firewire ports stopped working (front and back). I did a little searching around found a suggestion to try resetting the Mac's PRAM and NVRAM by holding the Cmd-Option-P-R keys down while booting. I have tried this numerous times and it doesn't seem to do anything (i.e. the Mac just loads OS X and doesn't re-boot like the instructions say). I'm using a MS Wireless Comfort Keyboard for Mac. Can you reset using a wireless keyboard?
Since I wasn't making any progress with that, I was toying with bringing in the Mac to a genius bar. Never having used the genius bar before - how does it work? Do I bring the computer in and leave it with them? Do they work on it while I'm there? I don't have an extended warranty so do they charge time and materials? I'm wondering if that might get awfully expensive and if I ought to just buy a PCI-X firewire card instead.
i got an aluminium imac. however, today when i tried to connect my FW800 Hard drive it did not work and it works by FW400. i connect the same Drive to my MBP using FW800 and it is working flawlessly.
i am still running tiger while the MBP has leopard
i wonder wether the returned My Book Studio has any effects on this. i returened it because i couldnt get it to connect via firewire. i really hate this as i use that lovely FW800 port a lot.
It WAS working. I'd bought an iomega fw drive with usb and fw800 ports. I hooked up the drive and it worked and then suddenly I got the message that a drive had been ejected improperly. The fw800 port never worked again -- with any drive or any cable. My apple care has run out. (I've tried these cables and drives on another computer.Â
View 1 Replies View RelatedThe Firewire port on my MacBook has stopped working. Nothing responds and when you look in System Profiler with anything connected the Firewire section shows the spinning indicator for a few minutes before claiming it is unable to list devices. I have also tried all the usual troubleshooting steps including resetting the SMC. But, if I put my thumb under the connected Firewire plug and gently press upwards the port works. It shows in System Profiler and drives mount. I have, of course, tried with different cables to rule that out too.
It clearly seems to be a physical problem with the port somehow. Does anyone have any ideas of exactly what the problem might be, and how easy it is to fix? Maybe a pin just needs bending outwards, or the port loose and can a clip needs pushing back in. If it is likely to be something relatively simple I am comfortable with fixing it myself, but the laptop is a few years old and not covered by AppleCare so I am wearing of an expensive repair bill.
I understand this particular issue has been discussed at length on this forum and in other places but none of the solutions have yielded any success for me and I see this is often the case for others. So, I'm posting the question again in hopes that there is an Apple guru out there who has figured this one out. (All relevant specs below.)Â
Problem: Firewire port was working fine for downloading video from a Panasonic PV-GS320 into iMovie 8.0 on an iMac 10.5.8. Then, suddenly the firewire port was no longer recognized: FireWire Bus: Warning:Unable to list FireWire devices. Maximum Speed: Up to 800 Mb/sec The problem cannot be with the camera or cable as I can swap them over to an iBook 10.4 and the camera and firewire download perfectly there. I have run AHT. Test results show no hardware problems. I've tried all of these
[code]....
3 times in the last week, my 400 & 800 firewire ports are not working. I am using a firewire hub with several external drives. I unplug everything, reboot and then they work. anyone know what is going on?
Information:
Power Mac G5
Mac OS X (10.4.2)
Both my firewire ports are not working. No signal or connection with external hard drive or video camera. Firewire does not appear under Network Status and is grayed out under Network Port Configurations.
Information:
PowerMac G5
Mac OS X (10.4.11)
When using the mini display port, do you need to power down the machine to plug it in and un plug it? I assume unplugging it on the fly doesn't mess things up oer the long term. Sorry kind f use to doing things on a windows where sometimes you have shut down the machine to do things.
View 5 Replies View RelatedI accidentally dropped my MBP and since then, my left USB port doesn't appear to work anymore. Its weird because when I plug my seagate external hard drive in, the lights of the hd come on but my MBP doesn't recognize it, likewise with my iPod, where the battery appears to be charging, but iTunes doesn't recognise my iPod.
View 3 Replies View Relatedcan I put firewire connector 400 in the firewire port 800?
Info:
iMac, Mac OS X (10.7.4)
If anybody here has a camcorder with a Firewire output, can you check something for me? I'm trying to use the front panel FW port on my new Mac Pro and it doesn't see my camcorder (Canon GL2) when I plug it in to capture footage. It IS seen if I plug the same FW cable into the port on the back of the ACD so that seems to rule out a bad FW cable. Also, the port seems to be working because it will see a FW CF cardreader when I insert it into the port. Any ideas? Is there a difference between the front and rear FW ports on the latest Mac Pro?
View 12 Replies View RelatedI have the Mac Pro and I have an external hard drive that I connect via the front FireWire panel on the Mac Pro. When the drive is off and the FireWire cable is connected to the computer, I get a "buzz" in the speakers. When I turn on the drive or disconnect the cable, the buzzing is gone? Any ideas?
View 3 Replies View RelatedThis is my first post on the forums, although I'm planning on looking around in here once in a while, to see what people are posting.
For starters, I just wanted to tell you about this little problem I've been having with my MacBook 1,83GHz.
Sitting at my desk at work one morning, peacefully drinking my coffee, I suddenly received a rather discomforting error-message from my shiny new (about 1 month old) MacBook;
"A USB devise is currently drawing too much power and the port will be deactivated.".
I have had some problems for about the past year with the front USB port on my 2009 13in Macbook Pro 5.5.
As you know, there are 2 USB ports on the left side on a 13inch Macbook pro. The one closest to me (the front one) works fine when I use it with a flash drive. But when I connect my external 7200RPM external drive to it, after about a minute, it ejects then re-recognizes the disk.
I video edit with FCP and use the external as one of my scratch disks.
At first I thought maybe it was the cord or the drive that was messed up. But then I connected my other external drive to this port and the same thing happened. But when I connected it to the back USB port, everything works fine. I haven't had any trouble. So i make sure it's connected to that port when using the external.
Info:MacBookPro, Mac OS X (10.6.8), Final Cut Studio 3
Is it possible to have the Mac Pro output signals from the optical and the headphone port on the front of the case? I like to have my speakers going as well as have one cup on my ear when listening. Surely there must be an application out there that forces OSX to do this.
View 1 Replies View RelatedI am having issues with my Dual Band 1TB time capsule for some reason the damn ports won't forward I have enabled the correct settings with the ip address and the ports, but when I use a program to test if the ports are open they are always closed, regardless on pc or mac. Does anyone have a solution to this? I even reset my Time capsule to see if it would work, but no luck.
View 1 Replies View RelatedI have found that by plugging in my Apogee Duet firewire audio interface and ONLY WHEN AppleFWAudio was loaded there was a 10c CPU raise that was making my MBP (late 2008) hot!I wanted to monitor the power that was required for Duet to run and to see if the temperature rise was due to that, so:With Apogee drivers uninstalled (just to be sure its not their drivers related, which is notMBP on battery power with System Profiler opened (to monitor the mA required by the computer from System Profiler -> Power)
View 5 Replies View RelatedWhat is this? I was comparing the Macbook pros and came across that option. What is it? what does it do?
View 6 Replies View RelatedI want to connect a video camera to stream video live through mivesta.com for cooking events. I understand USB streaming will not work on a Mac.
View 3 Replies View RelatedMy macbook does not have a firewire port. Is there any kind of adapter that will allow me to use my advc 300 (which need to plug in to the FireWire port)?
Info:
MacBook
I was looking into buying a mac book the new alumnin type that apple recently released for high school. And i found out that it doesn't have a firewire port so my question is if i buy the new mac book and someday i know i will need to transfer huge files like an imovie from one mac to the another mac so how would i do this? will Apple release a ethernet to firewire cable that will transfer files? I know you can use migration to transfer settings from another mac to this mac book using a ethernet cable. What will apple do about make a adapter for it or something? And when you start that laptop up holding down the t key will it go into target mode or will it just boot normally? Lastly Mac os x leopard requires a firewire port to install leopard on it. I know they clone the hard drive from a huge machine before it gets into the laptop. But when the new operating system mac os x snow leopard is here i am pretty sure it will require a firewire port to install it so will i be able to upgrade it my self at home?
View 7 Replies View RelatedI work at a photo studio, and we just bought a new mac Mini to power a rather old Phase One digital back. This device requires quite an amount of power, and it appears that Apple made the voltage output of the FireWire port drop with 200mV on the new intel motherboards. My question is: Can you, in anyway, get that voltage output up again? If this means playing around with dangerous settings, then be it. We just need it to work! We tried to buy a Lindy FireWire 800 Repeater, with an external power supply, but doesn't work at all. Perhaps it's just a poor repeater? Is there any other devices out there, that could make it work? Perhaps some solution with a battery attached to the FireWire cable it self.
View 6 Replies View RelatedMy MacBook Pro (OSX 10.6.8) can not find the FireWire port. Until now there hasn't been any problems using the FireWire, but now it just deny any knowledge of it, so to speak.The audio device lights up when I connect it to the MBP (yes, I did connect it when in off-mode), so it seems to work in a way.
View 1 Replies View RelatedIs there a way that I connect a firewire to my MacBook which doesn't have a Firewire port? I need to connect an External HD (not via USB) to my MacBook but just now realised that I don't have a port!
Info:iMac, MacBook Aluminum + 7 more Apples!, Mac OS X (10.5.6)
I am working on a friend's G5. It won't go to sleep. The monitor does, but not the CPU. I have upgraded the firmware, to 10.4.10, zapped the pram, corrected permissions. Just at a loss.
This computer worked fine at work where she had it originally, but when she shut it down and took it home, it has insomnia. Also, one of the front fans sounds like it is scraping or hitting something. It is not a loud noise and the fans still work, just annoying to her since it won't sleep. (Sounds like my one month old).
Information:
XServe, Mac Pro, G5, G4Powerbook
Mac OS X (10.4.10)
Silver front G4 won't start up. Recently replaced back up battery when this condition occured, start up fine. Computer was turned off for about 2 weeks while out of town, but now the on button lights momentarily, no boot uo. Won't even do that unless power cord is removed and re-inserted.
Info:
Mac Pro, Mac OS X (10.4.11)
Does anyone have any good suggestions for connecting a DV port of a camcorder to the new MacBook which lacks a firewire port?
View 5 Replies View RelatedI have cable TV streaming in through my Firewire port. What is a good program for viewing it? So today I decided to run a cable from our TV room to my laptop desk so I can watch "educational" programming. But I ran into a small problem:
CableVision to old VCR so I can make use of its built-in tuner, RCA cables from VCR to ADS (Converts inputs to RCA & Firewire out), and Firewire from ADS to MacBook.
This all works fine but I then realized I have no decent program to watch the video on. I can open Quicktime and see a small window, and no doubt if I hit record the sound would be captured as well but the sound is not audible while monitoring. I tried iMovie and again had a small window to watch. Still not what I want. So what can I use to watch the video from my Firewire full screen and with sound?
