We have an Xserve (intel) with two ethernet ports running on OS X 10.6.8 server. It is connected to our network and sharing files with local users and authentication from our PDC (over an AD network). I need to setup a private network so that we can keep a few PCs off of our primary network (primarily to keep them from getting updates pushed or malware). Using the two ethernet ports, this should be do-able. It's practically automatic on a couple Windows boxes we have setup. However, when I plug a small router into the second ethernet port, I instantly lose the PDC communication on the other. I'm not sure if there are other issues at this point or not because there hasn't been a time when I can bring the system down (yet).Â
I am using a 2006 Intel Xserve (10.6.8) at home for storing lots of multimedia. My 2 TB user drive, which is inside of one of the Xserve's drive caddies is nearly full. I purchased a $157 3 TB Seagate Barracuda (Model No. ST3000DM001) from Amazon and put it inside the caddy. It is not being recognized at all. Looking around for solutions I am getting a hint that trying to restrict the data rate to 1.5 GB/s might help, which is documented for some of Seagate's older SATA drives, where one puts a 2-mm jumper clip on a header next to the SATA connector. This 3 TB model has the same header, but the manual only speaks of data rate autonegotiation. I'll be able to try out the drive with the jumper clip in place tonight and will report back. Curiously, in my Thermaltake USB-2 interface (toaster style), Disk Utility shows the drive as "801.57 GB Generic External Media," which is being discussed in a Leopard Server discussion thread. Last I saw, there was no good explanation for this symptom.Â
Info: Xserve, Mac OS X (10.6.8), Apple has made quite a bit of money off me over the years.
Is it just a server? and how much do they go in retail shops / stores??
I would like to find out as i have a mac mini, g5 quad and a macbook.. just a fan of apple mac lol. I do alot of webdesigning for many clients, could the xserve be a way to i don't know host these clients or something if it is a webserver?
Apple on Friday added a new server option to its Mac Pro lineup Friday, with a $2,999 system that is designed to replace the Xserve hardware which will be discontinued in early 2011.
The Mac Pro Server comes with one 2.8GHz Quad-Core Intel Xeon "Nehalem" processor, 8GB of RAM, and two 1TB hard drives. It also has Mac OS X Server unlimited with a client license, and an ATI HD 5770 graphics card with 1GB of GDDR5 memory.
The new configuration starts at $2,999 and ships in 2 to 4 weeks. Apple's previously available quad-core and 8-core Mac Pro systems ship within 24 hours, while the 12-core model takes 3 to 5 days to ship.
The new Mac Pro Server can also be upgraded, with custom build-to-order options offering up to two 2.93GHz six-core Intel Xeon "Westmere" processors, for a total of 12 processing cores at an added cost of $3,475. Users looking for the best possible system can also add $3,400 to the price and get 32GB of RAM.
The new hardware became available Friday after Apple quietly announced on its website that it would no longer offer its Xserve rackmounted servers after Jan. 31, 2011. New Xserver orders will be accepted through that date, and the hardware will be backed by Apple's standard one-year warranty.
Apple also issued documentation aimed at helping customers transition from Xserve to Apple's remaining server options, the Mac mini Server and Mac Pro Server. Apple's guide notes that the 12-core Mac Pro with Snow Leopard Server meets or exceeds the performance of the baseline Xserve hardware.
However, while Mac mini with Snow Leopard Server is much less powerful than Xserve, Apple's smallest desktop footprint has been the company's most popular server system since its introduction in the fall of 2009.[ View this article at AppleInsider.com ]
Since I'm newly registered on this Forum I can not deal with on my own. We have about 20 intel- based Xserve (headless). Everything works fine except of serial console - there is no way to connect to it. There are only few random characters displayed on system start and thats all. I've tried all connection settings that are mentioned in Apple documentation (57600 8N1, 9600 8N1 etc.. ) with no success. I'm using ZTerm and PL2303 based USB RS232 adapter- no problem with serial console on sun, cisco, brocade and many more . Connection with older xserve's is also possible. I have to put all machines into production, but I can not do this without reinstalling Mac OS X - Raid 1 on OS slice is required. I can not start OS installation with no graphic card or serial console
My Xserver 10.5.7 has spontaneously lost its Administrator password so it will not let me in to give it a new one. I don't have the Server Installation disk any longer, is there anything I can do to get back on the Xserver computer?
I want upgrade our xserve from 2 x 250GB mirrored discs running Mac OS X 10.3.9 on xserve to running 1 x 250GB system disc (keeping other as spare) and 2 x 500GB mirrored data discs. (Then upgrade to Tiger).
Can I break the software mirror with: diskutil destroyRAID /dev/disk{x} or does this destroy the data too? Would I be left with two working, bootable discs or just two RAID slices? If the latter, how can I convert them into 'normal' bootable discs?Would it be better to upgrade to Tiger first? Or not make much difference?
My new Xserve started up and I was able to configure it remotely via Server Setup Utility then after I input all of the settings it hung on finishing the setup for about an hour. I then restarted the Server and now I cannot see it.
i have a domain controller and active directory based policy win 2003, one xserve running mac os x server 10.6.8 and alot of macs workstations. How can i push login script on all macs without adding it in login items? The script i want to store on smb or afp share disk, and will be edited from time to time. I've tried to add it on xserve from WGM, but it threw an error that current directory schema doesn't store desktop settings.So how can i solve this?
I run 10.6.8 server in a VM with Parallels Server for Mac. Lithium pinged me early Monday morning to tell me that my calendar server wasn't reachable. I found it had kernel panicked. After resetting it and verifying the directory structure and permissions, it booted fine. But availability or free/busy wasn't working for all users! The events were all there. Invites could be sent and received but when a user checks for availability when creating events. they see the daily work hours grayed out but not anything corresponding to a scheduling conflict. Â
Things I have Tried:
- bounced ical server
- Rebooted the server
- checked the owners and permissions for the data store hierarchy. (_calendar:_calendar 750)
- checked for xattrs on .ics files in several calendars
- deleted .db.sqlite for several users in several dir in their calendar stores
- in the past I have found that some iTIP invitations seem to get "stuck' causing problems with an individual users free/busy and deleting the inbox resolves this so I deleted several inboxes
-I moved a copy of the data store to a test server and pointed several clients at it.Â
The issue persisted in all of these cases without any change in behavior with one exception; somewhere (i lost track of where) during this process users also lost their delegation preferences. I'd love to find out how and where that is stored so that it can be restored in the future. It seems pretty fragile...Â
I found one way to restore the functionality; copying a users __uid__/<GUID>/calendar out. . Moving all the folders under <GUID> out of the way and dropping the .ics files into ical with their account configured in that instance. Although this worked for selected users, I have many, many users and calendars so this solution would be suboptimal. Â
my problem is that on a restart of one of my 10.6.8 Servers parts of the Serveradmin configs are gone while some of them persists. The lost configs are everytime the same: VPN (complete) and iChat (a secondary but very important Host-Domain). Of course a can restore them from a backup but that shouldn't the standard procedure after a restart....Â
I am running an open directory/active directory network. Authentication is from the Windows server 2003 active directory. It has worked fine until the last month. Now clients stop authenticating & when I check the AD plugin it says network accounts are not available. I can force the server to unbind, then renew the binding & everything works great.Is there any work around or fix for this other than upgrading the windows server to 2008?Â
I had a goodworking SUS (10.6.8) working but the drive is getting full so i change the location of the files to another disk (in the xserve)and follow instructions from Apple (page 84 from the manual System Imaging) sudo cp -p /private/var/db/swupd/html /Volumes/My_Volume/My_Software_Updates_Folder/This works and i copy the files to a new drive. I also change the SUS so that theu host files for Lion clients url..works also, start SUS in Server Admin but when clients wants to connect i get an error that there is no SUS available and when i use the browser for an check i get een Forbidden error url...ForbiddenYou don't have permission to access /index.sucatalog on this server.Apache/2.2.21 (Unix) Server at 127.0.0.1 Port 80.
Trying to set up the Software Update Server under 10.6.8 Server. Have everything set up properly as per Apple's documentation, but all clients error out on software updates (saying they can't find the index. sucatalog file). When you view this file, which is an alias, within the HTML folder that is created when you enable the Software Update service in Server Admin, the alias doesn't link to an original.I've tried this on two separate 10.6.8 Server installations and I get the same error on both machines.Where is the alias "index.sucatalog" supposed to point to?Software Update Error Log in Server Admin says "Symbolic link not allowed or link target not accessible" and points to the alias file.
Info: Mac mini, Mac OS X (10.7), Xserves (Early 2009, Early 2008, G5), Mac Pro
My system is MacPro 2009 with 10.6.8 server and Apple RAID card. Last week, RAID util just notified me of one drive is not viable, so i decided to replace the drive today. The configuration of my system is... There is an Apple Raid Card for HW Raid system Bay 1 = 640 TB drive with Mac OS X 10.6.8 server installed Bay 2, 3, 4 = 1.5 TB drives set up as RAID 5 below is what I did to replace the degraded Bay 4...Â
1. I shut down the system
2. replaced the corrupted drive with the new hard drive
3. tried start the machine again.Now my machine refuses to start up with the blinking question mark... I guess that the system fails to recognize the new drive or cannot find the system files...Â
4. So I put back the degraded drive...
5. The machine still won't start...
6. I tried to use the 10.6 server installation disk to boot up the machine to check if I can fix the system via disk util; but, everytime I do this, I got kernel panic... Â
7. resetting PR Ram didn't help, cannot boot up via safe mode as well (since the system file is not accessible now, I guess...).
8. booting via 10.6.2 server installation DVD still gives me kernel panic... Â
Why would my system corrupt by just replacing one degrade drive? The Mac OS X is not even the part of the Raid system... How am I supposed to fix this issue with out the installation disk?
Years before Mac OS X 10.0 was first released in 2001, Apple launched Mac OS X Server, targeting its newly acquired Unix-based operating system technology at the education and workgroup server market. Apple has struggled ever since to find a broad server strategy that works. The solution may be as obvious as the iPhone App Store. Mac OS X Server has remained firmly stuck in the background even as Mac OS X has blossomed. Over the last decade of Mac OS X's development, Apple transformed its legacy Mac operating system from an outdated relic stuck in maintenance mode throughout most of the 90s into a highly regarded system that gets as much or more respect from industry critics as any other desktop operating system.Apple accomplished something that many others in the industry failed to do: marry the power and familiarity of Unix with accessible ease of use in a commercially successful product. Ray Noorda tried to do this at Novell in the early 90s; Caldera's OpenLinux also failed to take over the task from Novell ten years ago. United Linux and a series of followup attempts to standardize Linux all failed to accomplish their aims. A variety of efforts to sell Linux to consumers since then have all made very little progress outside of a small niche of hobbyist users.
Up until a recent update, software update was working. Now it just crashes. I've tried deleting the Pref's and downloading updates directly, but that hasn't helped.
I'm trying to install a SSL Certificate on a mailserver under 10.6 server. I dont know what to do by intermediate certificate and choosing type on certificate assistant.
Server version is: 5.0.8 Current available seems to be : 5.5.24 community server available from h [URL]if I already have several databases running under 5.0.8Â what are the hazards with upgrading to 5.5.24 community server?
I can't seem to get the App Store to sell me Lion Server for my Snow Leopard Server.I'm trying to remain positive about this but I'm getting really that money isn't enough to make this happen.My experiencewith the App Store and Apple policies in general is its almost time to dump OS X and head back to Open Source.I put money in my iTunes account.I've done the 15 logins it takes to satisfy AppleID my account is complete and up-to-date in the store and the Support Communities.How do I buy the software and actually download and install it?
Info: Mac mini, Mac OS X (10.6.8), upgrade to Lion
I only have macs in my network and am not aware of any mac viruses. Afer I had the chance to review everything it became clear the e-mail server was sending out e-mails. SMTP logs for my mail server showed numerous attempts between yesterday and today to send out e-mails. Considering my mail server has not yet been launched and is not being used to either send or receive e-mail I imagine the work must have been done by a hacker ro sometoner else who hijacked my mail server to send out spam e-mail to others.Â
How can I prevent this from happening again the in future? Is there a security setting that would prevent this? My firewall had a relatively long and safe password but I changed it today just in case. Also, I changed the password for both the firewall and server. Will this help or is it possible for a hacker to connect and gain control of mail mail server without the need to know these passwords? If not in OS X Server, is there a third party application that would protect the mail server from this in the future?Â
I have a Snow leopard server with a folder shared Via SMB for the 2 PC's we have, all the macs can read and write to this folder OK. About once a week the 2 pc's take 10 mins to start and then cannot connect to the share. Web/email and sharing betwen them still works. I can ping the server from both. I've turned off the smb and restarted it. Also tried restarting the Xserve. This still has no effect. All internal firewalls are off. I've tried guest access.
I'm trying to using Server admin on a remote Mac to manage our xserve. Both are running 10.6.8 and I've installed the Server Admin tools onto the mac. Both the Workgroup manager and Server Monitor work OK on the mac, but whenever I try and connect the Server Admin it always comes up with the error : "The login information is incomplete for this server or is not valid. The server failed to accept the login information you provided for <servername>. Check the name and password and try to log on again" I can't connect using the server name, FQDN, or IP address. The macs are all using OD and AD and I've tried both AD and local OD accounts (all administrative) but to no avail. DNS is working OK and I can resolve the server-name with dig and dig -x. I can screen share the server so connectivity isn't the problem.Â
I've googled and searched, I can't see what I'm missing, so I am turning to the community for help, because I simply don't get this. I own 2 domain names. I'd like to use the build in Mail Server application into SL Server, so if your suggestion is using another mail server, please don't post that.Â
Let's say my domain's are domain1.com and domain2.com I've looked at the Mail Server Admin user guide, and I've followed a couple of wizzards, and... all in all, I am getting no where. Let's also say my email client is my iPhone.Â
Ok, so domain1.com currently has no email with my current provider, and domain2.com currently has email from my current provider, it's my desire to eventually switch this, but experimenting on domain1.com will do no harm, so I am experimenting on this. Both domains give me the ability to point to an mx address.Â
Here's what I've done. I've got my user created in Workgroup Administrator, and I am confiuguring my LDAP3v, and I am authenticated enough to create and delete users.Â
***I Should note that DNS is currently disabled, I gathered from all my reading that I don't need the DNS enabled because I manually put in the MX record to mail.domain1.com and domain1.com is correctly identified. The server is also the webserver, and all the web server functions are working as expected! I don't know if not having the DNS enabled is holding me back or not ***Â
1st, I enabled the mail service in the Server Admin. My domain name is ServerName.local and my host name is mail.domain1.com (I created an a entry in my dns settings for that). Enable SMTP is set, IMAP and POP are enabled as well.
I don't intend on setting a relay, because I want this server to do send email out. I do have some cases where I send a mass email out, not for spam but for Christmas card purposes, and I think this is a good free way to not have to limit myself to batches of 50 or so.
I have my created SSL certificate, and havce only the Kerberos and CRAM-MD5 settings set in the security.
In my hosting section, I have enabled Virtual hosting, and listed my domain1.com and domain2.com below.
Now in workgroup manager, I've connected to my LDAP3v database and created a test user, and a test group. In the server admin, I added the test group to the list of authenticated mail users. I made my test user a member of the test group, and made that his default group. I enabled the mail service, and set the mail server which is ServerName.local, and enabled POP and IMAP.Â
That's it. I've done nothing in terminal, just that. I was getting a user unable to authenticate error, it was able to download the certificate though. Then I realzed I had an MXE defined in my settings for my DNS domain manager. So I changed to an MX, to mail.domain1.com and then I created mail.domain1.com pointing to the same IP address as domain1.com, and unfortunately the DNS records haven't updated yet, because I initially didn't create the mail.domain1.com entry, and now it's saying the server isn't responding, so I am anxiously awaiting an update from the DNS in the world to see if the issue has now cleared up.Â
Info: Mac mini Server (Mid 2010), Mac OS X (10.6.8)
I just configured my Snow Leopard Server to distribute Lion update's [URL]I also see that the sync is competed with all latets Lion update's and all are enabled. I've adjust all the settings on the clients:sudo defaults write /Library/Preferences com.apple.SoftwareUpdate CatalogURL [URL]The problem is that all my 10.6 and 10.7 clients doesnt see any availble update's and running the Software Update on the cllient i get the message "The software is up-to-date" I checked all the configs.....reset the complete SUS server and started all over but still the same issue!
