Three days ago a noisy fan brought me to the Genius Bar at my Apple store and when i got there the boot screen stayed gray and had a folder with a question mark in it. I have a late 2006 15" MPB running Snow Leopard 10.6.6. The guy told me i need a new hard drive so i went out and bought a Western Digital Scorpio Black 320g 7200 rpm SATA drive with a 16 mb cache. I replaced the old one with it, formated and installed OSX 10.6. I then used my time capsule to recover my last back up. I completely restored it. TWO DAYS OF PERFECT USE Now, i have the annoying fan noise again and my console is telling me that my HDD is having disk0-02 i/o errors. A LOT OF THEM. I've had at least 30 before noon today. Currently i am writing zeros to my drive and going to reinstall 10.6 WITHOUT using my time capsule restore (incase that has bad blocks written to it) Has any one heard of issues like this before with the particular HDD i bought? Two HDD failures two days apart seems fishy to me, what other issues should I be looking at? Is it possible i'm getting the i/o errors from a bad HDD ribbon cable to the logic board?
The thing is I dont really need 500gb of space. But from reviews Ive read that the 500gb is faster in some cases because of its higher platter density. Vibration /noise issues on the scorpio black 7200rpm sway me towards the scorpio blue 500gb as well.
Anyone had experience of either hard drive or both? (this will be for a 2.2Ghz MBP)
I was trying to upgrade my hard drive on my 2009 15" MBP 2.53GHz to a 7200RPM WD Scorpio Black 320GB BEKT I had. The WD HD had Leopard on it, but when I swap the HD into the machine and boot it up, the machine just hangs and the Apple sign won't even show up. Then I plug in the original HD to the machine as a external device, and boot up the machine with OPTION key to select OS. It properly show up the partition I had in the WD HD and the external HD. When I click boot from the WD HD, it hangs again. I then switch back the HD and use my original HD to reformat the OS partition I had in the WD HD, then swap the drive back again. I boot it up and enters the Snow Leopard installation disk and begin installation process. It took forever to finish the installation. On my original HD, it only took 21 min. to do a clean install. Now with the WD HD, it took 33 min. to get 10% of the installation process done. I then took out the WD HD and did a surface scan on it, but no bad sectors were found.
I want to upgrade the HDD in my Macbook Pro 2010 that currently has the stock 5400 250Gb drive in it. I am torn between the Momentus XT 500GB version, which is on sale at newegg right now for like 69, or going with the Scorpio Black. The differences that have me stuck is the 32 vs 16 cache, as well has the added speed of the seagate compared to the laundry list of problems people have reported with the XT. This will be my first HDD upgrade, and was looking for a little direction.
I just upgraded my friends Macbook Core 2 Duo to a 500GB Scorpio Black 7200 RPM. I used both XBench and AJA System Test to test hard drive performance and the Scorpio Black is definitely a faster drive. Using AJA system test, my Apple upgrade 7.2k Seagate drive is about 90 MB/s, while the Scorpio Black is around 105 MB/s Do these numbers justify an upgrade on my machine?
As I'm about to purchase my 2009 MBP unibody I want to upgrade the HDD myself as I've posted before on however will either of the WD scorpio black models work? it comes with or without the freefall sensor? will either be compatible? I read on some retail sites that one won't work with the computer.
Is this hard drive compatible with the new 2010 13" MacBook Pro? [URl] I plan on upgrading the stock 250GB hard drive in the base model 13" (2010 model).
i plan on upgrading my macbook pro 13" to a scorpio black. Should i get the version with or without the freefall sensor. I heard the sensor conflicts with the sensor built into the macbook pro and causes kernel panics.
I'm looking at a MBP on CL and the seller has swapped out the HD and put in this WD Scorpio 320gb 7200 rpm HD. I'm wondering if any of you have this hard drive and can confirm it's quality or claim that it is of poor quality?
I installed the hard drive with no problem and have experienced greater performance, no clicking nor vibration, and no freezeup or rainbow wheel. I also did a clean install of Snow Leopard. I did a PRAM reset at the beginning and calibrated my battery. However, now I noticed my battery is draining FAST, only lasting 2 hours. I looked a little online and discovered I may still need to reset the SMC (shift-control-option + power key), which I will do shortly. The battery lasted 6-7 hours before with my old hdd and is at 96% capacity.
I'm aware that there are probably a dozen of these threads around in the forums, but if you have the time to tell me to search it up, then you have the time to answer my question. I am fully aware that this may void my MBP's warranty. I've decided to go with either the 500gb 5400rpm WD or Seagate. I'm just wondering which drive is more reliable and faster. Also, when installing the hard drive, is it ok to use a magnetic screw driver. Someone told me that there's an application called Superduper. It clones the original hard drive to make the upgrade easier. Is this a good application, or are there better options?
I am planning to purchase a 13" Macbook Pro base model (first Mac by the way), and I want to upgrade from the stock 160Gb HDD.
I don't really see myself needing 500Gb, but I have read that a higher density drive outperforms a lower density drive. Newegg currently has the 500 WD Scorpio Blue drive listed for $30 over the 320Gb edition. Will I see significant performance increase by going with the 500Gb model instead of the 320Gb one?
What about power consumption? Is one better than the other?
I just got my new MBP and it has a Toshiba MK5055GSXF 500gb inside. My old one has a WD Scorpio Blue 500gb. I know the Scorpio Blue is supposed to be fast for a 5400rpm. Does anyone have an opinion whether it would be worth it to switch them? Is the WD superior?
I have a White MacBook version 3,1 made in 2008 w/ the intel ICH8-M AHCI SATA controller. Unfortunately this controller is only 1.5gb/sec. I picked up a WD7500BPVT, WD Scorpio Blue 750gb, with a spec of 3gb/sec. Western Digital tech support assured me it would step down to 1.5gb/sec, no jumpers needed (as it isn't configurable by a hardware jumper). So I install it in my MacBook, boot up from the Snow Leopard install disc but it doesn't see my fancy, schmancy 750gb drive. Is the drive not seen because of a compatibility issue w/ the SATA controller? If so, what is the largest capacity 9.5mm drive someone has installed in a MacBook w/ the intel ICH8-M AHCI SATA controller?
I am looking for advice on the wd5000bevt (500GB 5400rpm) Planning to get this as it supposedly has almost the same speed as a 320GB 7200rpm drive and doesnt come with the usual 7200rpm negetives (heat, vibrations and noise). Anyone with firsthand experience with this drive? It is quite popular so I am hoping I will find someone Also, I heard something about clashing motion sensor because the macbook already have one so you should avoid some drives. Does this drive have one? Is it compatible?
I just upgraded my hdd to a 500gb WD scorpio blue in my 2010 MBP 13". It seems to start and stop a lot more than the apple one (if that makes sense). and every now and then the computer seems to lag for 1-2 seconds when doing things like typing, scrolling, etc. I've tried searching and found other people have had similar problems with older MBPs and they talked about some EFI firmware or something. Does this apply to my MBP too? Or does anyone have any other suggestions of what I can do?
Ok guys, so here is the story, i just bought the 500 GB Blue Scorpio, ran the Time Machine back up on an external hard drive and wanted to install the 500 GB on my macbook, inserted the Mac OS CD and in the section where it asks where you want to install the Mac OS, i didnt see anything it was blank and it didnt give any options or anything.so now i installed the old hard drive and i am using that one, what am i supposed to do ?
I've recently bought a WD Scorpio Blue WD5000BEVT 500GB 2.5" SATA hard drive to put in my PS3. I decided instead to put this in my MacBook Pro and put the 320GB drive from my MBP in the PS3 - which I have done and works perfectly.
Now the problem is the WD HDD in the MBP. I can physically hear the HDD spin down and then almost immediately spin up again. Whilst in this state of "spin down" OSX is a little unresponsive. Does anyone know how to stop the drive from shutting down so often. It literally happens every few seconds. I haven't noticed the problem when booted in Windows 7 though I could be wrong.
I'm looking for a few good ways to transport and use my UMB. I figure buying a hardshell case & a timbuk2 bag seem like a good combo. Question is - which do you guys think is better, the Speck or Incase cases? Anyone have any experiences? I had the Incase hardshell for my old whitebook.
Seemed to work out alright. The other option I thought of was getting the invisible shield. Anyone have any thoughts?
my 2.4ghz 3 year old macbook pro is experiencing a lot of graphics errors and lockups recently, where the screen will turn garbled and such and the computer will freeze. Keep in mind this is the 8600m gt. However, I just got the nvidia fix done for free by apple a couple months ago. Is it possible it could be the same problem?
Alright so someone needed the errors for a program, and I noticed there were several other errors for programs that are no longer on my mac. Is there any way to figure out how to make my mac stop looking for these things to rid the errors from Console?
recently I asked a tech about my crash macbook. [URL] I didn't have an external hard drive, and by the time I bought one, the support chat thing had expired. But I finally have one now. Anyway, I'm trying to save my files using the external hard drive and the instructions that the tech gave me. "Don't give up on your files, yet! If you don't have a backup of those files, then you should attempt to get those files. Here's what I would do: Get an external hard drive. Boot to your OS X installer DVD. Run Disk Utility from the Utilities menu. click on your hard drive, and click the Restore tab. drag your internal hard drive to the Source line. Drag your external hard drive to the destination line, then click the Restore button. That might back up your files all in one step. You may need to wait for several hours for that to finish."
I just tried that, and it worked fine until I tried to drag my external hard drive to the destination line. It dragged it over and then let it go on the destination line, but nothing appeared. I was wondering, why might this be?
Me and my friend are having a problem with his macbook pro. He has some files that need deleting in is recycle box, when he clicks on empty, the recycle bin looks as if it will load then just stays in the loading stage trying to find files to delete, sometime after restarting mac and repairing disk the recycle bin finds the files that are to be deleted but then it pauses half way through or at certain points and will not continue!
I am experiencing read errors on my roughly 2 year old macbook pro 15" on its built-in apple 500gb SSD.
Should I run to get a replacement? Where and which?
I used SMARTUtilities and the long run test confirmed the read error. It showed in a large windows 7 vmware vm (about 45gb), or in one of its hd-file sections of 2gb size.
I have Love Film on the mac air and it has worked a dream until last Saturday. While I access the site easily and select something to stream it is coming up with a DRM error. I have checked everything in Silverlight and un-installed and re-insalled and check all the required boxes but nothing!
The only other chnage I made to the laptop was downloadng Mackeeper that same and perhaps it is a coincidence that I can no longer receive streaming since that time.
My MBP has been reporting issues over the last few days and recommending that I verify the disk. Whenever I do this, it says that it finds errors and I should reboot with comamnd-r pressed and choose disk utility. Which I do. However when I try to verify the disk or repair the disk in this mode, it never finds any issues? Logging back in and running disk utility will again report issues and recommend repairing What should I do?
