Hardware :: RAID Drive Has A Bad B-node Tree Error - How To Repair
Dec 27, 2007
I set up a RAID using 4 Segate 320GB SATA drives in it's own box. It is connected to my G5 (OS 10.4.1) via a Highpoint RocketRaid 2210 card. After 2 months, I have gotten the b-node tree error twice. The drive fails to mount and drive utilities (including Drive Genius, DiskWarriror) can't fix it. I was able to use Drive Rescue 2 to get the info off of it, but I am concerned as to why this keeps happening. I can reinitialize the drive and get it working again, but this is not a solution.
I have a 17inch intel iMac, early 2006 (the first release). A couple of days ago it decided it no longer wanted to boot up. Inserting the install DVD and running disk utilities verify/repair, it said that the volume had an invalid b-tree node size, and attempting to repair the volume failed.
Everything is backed up from this computer, so at this point in time I am only worried about getting it running again. So, I dug deeper to resolve the issue.
I have two disks containing data organized in a RAID 0 array. I have a MacPro running Snow Leopard. Recently, the RAID array does not show up in the Finder and is not accessible. Disk Utilities can't inspect or repair the disks because of the dreaded B tree node size error.
Can these disks be salvaged? Can the data be recovered?
I have a late 2006 iMac, which I know must be at the end of its life now, but at the weekend my main internal HD developed an error, and it wouldn't boot, even from the recovery partition.
I managed to find my old Snow Leapard disks and ran Disk Utility on my HD (when it actually saw it) and the error it came back with was "Invalid Node". After trying many things, I had to reformat and reinstall from my Time Machine back up, which went really well.
However, once all restored it tried to do a backup and it failed. I then went into Disk Utility again and it found the same error on the Time Machine drive.
Therefore, my question is, could the back up process have copied an 'error' to my back up? Or is this a fault somewhere else (Disk Management etc) that I need to watch in case it cases errors with my other drives that have important information on?
Two days ago my MacBook (OSX10.4) crashed; VLC player froze when I was watching a tv show. I though 'no biggie, happens now and then' and hard-resetted my 'book. Tried opening the file again with Quicktime, again, computer froze up. Waited a couple of minutes, hard-resetted my laptop again. Only this time, the screen got stuck on grey/lightblue-ish screen during boot-up.
Tried a lot but couldn't get my MacBook up and running again. Started up with the OSX cd popped in and went to Disc Utility. Mac then told me there was a 'Invalid Node Structure' and that 'The volume could not be repaired'. During a third or fourth start-up this changed to Mac saying there was a'sibling error'.
I checked some sources online, figured out this should be something fixable. One possible option was Disk Warrior. Supposed to be *the* tool with problems like these. I replaced my malfunctioning HD, put an old HD in my MacBook, reinstalled OSX and put the malfunctioning HD in a stand-alone case and connected it too my MacBook. As we speak DW is busy rebuilding the directory but it has been doing so for over a day now. I've read online that it can take a couple of days though. My HD is 250Gb with 30Gb empty space when it went kaput.
Now, there seem to be a couple of other alternative options. These lads talk about Tech Tool Pro - apparantly some other program that could help: [URL]
Then there's a couple suggestions/methods mentioned online that either involve booting up in single-user mode and type some code [URL]
Has anyone ever had their HD act up like this? Any experience/recommendations regarding the programs/methods mentioned above? I'm pretty new with Mac (used PCs for ages, switched to Mac quite recently) and I'm kinda at wit's end here :/. I was in the process of backing up my stuff, but there's a boatload of data on that HD that I hadn't archive yet.
I have a PowerMac G5 and need to purchase an internal RAID card to create a RAID 1 mirror of the system drive... one that will allow me create a Hardware RAID 1 mirror, not software RAID through OS X.
Uhh hard to fit the title, but in System Profiler - Sata device tree, normally you see <hard drive name> and underneath it <partition 1 (IE Macintosh HD)>, however since installing my SSD, everything shows <SSD NAME> and then the SSD partition but also shows hard drive partitions there?
My iMac has been crashing a lot lately and finally it's hard drive just up and failed. I have been doing hourly Time Machine backups to a concatenated RAID set (2 USB drives of 1 TB each). However, I think the iMac crashed while backing up and hosed the RAID controller.I've since plugged the two disks of the RAID into my MacBook Pro to see if I can repair them. I can see the individual disks of the RAID in Disk Utility. I can even verify and repair them. But i can't do that with the RAID in the sidebar, and it won't mount on the desktop. When I try to eject it from the DIsk Utility file menu, it says disks are in use.
I'm pretty sure my data on the two disks is intact, but I can't seem to get the RAID to mount as the single concatenated set on a desktop, which makes it inaccessble. Is there a way to repair the JBOD RAID without losing all my data, so I can then restore from the latest backup to my hosed iMac?
I have a RAID 0 set up with two 1.5TB HDs. I am doing some reorganizing and want to take all the data on the RAID 0 and move it to one of the hard drives in the RAID 0 and create to single drives. Is there any way of moving all the data from a RAID 0 onto one of the HDs?
I'm having some trouble with my Macbook. It's running on Leopard 10.5.8. I recently tried to partition my hard drive and while doing so it prompted me informing me that there was an 'invalid node structure'. I could then no longer proceed with the partition. I had planned on updating my OS to Snow Leopard. I wanted to partition my internal HD, so I backed up some files on my external HD. I basically wanted my interal HD to run smoothly with a new OS while minimizing the space used. Now I've come across this issue where there is another message being prompted that says, 'invalid sibling links on hard drive'. I found THESE steps on another forum that informed me that this might restore the hard drive back to a readable/functional state but that didn't work either:
(These were the steps I took and nothing happened except another prompt informing me of an 'invalid node structure')
Boot off the OS X CD (reboot, hold C while booting).The installer will load up, go to Utilities in the menu and run Terminal.Type df and look for the drive that has your Mac system mounted---you'll have to unmount this. On my MacBook Pro, it was /dev/disk0s2.Type umount /dev/disk0s2, replacing disk0s2 with whatever disk your OS lives on.Type fsck_hfs -r /dev/disk0s2. If you umounted the wrong thing, it will complain that you can't repair a mounted drive. Go back and umount the right thing and repeat this step.
I then stumbled upon a few different forums mentioning something about Disk Warrior. I was wondering if THAT would resolved this issue. Honestly, I don't really want to spend much money on buying this but I WILL buy a new hard drive if I ABSOLUTELY need to. I was just trying to see if I can troubleshoot this before I decide to throw in the towel and buy a new hard drive or attempt to try out this Disk Warrior thing.
i have a problem that everytime i restart my imac (late 2007) i get the blinking folder for 15 minutes up to a couple of hours then it starts up normally. i tried clearing up the PRAM. reset the SMC. and it still happens.i tried to do from the system a repair disc permissions and i got back one error that cannot be fixed which was
<quote> Warning:SUID file"System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents?MacOS/ARDAgent" has been modified and will not be repaired.</quote>
i have even tried to fix the error from the bootable CD, but same error. i even upgraded to snow leopard but no apparent change. i dont even know if this is the cause of the problem. but all other stuff is OK. even the boot CD hardware thorough check was all ok.i still get some noise of the fan when i boot up for a couple of minutes then it goes away.but temperatures are quite good and fan speed is around 800rpm at the moment and no sound is to be heard.
I ran a fix permissions today, and got the following errors. I have no idea what they mean, and am a bit concerned. Anybody have any idea what this stuff means?...
I just tried to verify my HDD, and Disk Utility said: Invalid node structure. Volume check failed. Error: Filesystem verify or repair failed. Now when I tried to reboot my Macbook, the gray Apple comes up and so does the spinning wheel, but after a couple of minutes, it shuts down.
Getting error code -1309 when trying to copy a .dv (clip-2008-08-10 11;31;11.dv) file to external harddrive via Firewire port at 400 speed. File size is 6 GB.
I have an iMac OS X 10.5 or 6? that was not getting past the apple logo and spinning gear, so I started from install disks, selected Disk Utility, and got the following messages. The lines in Caps were red
Checking Journaled HFS Plus volume Checking Extents Overflow file INVALID LEAF RECORD COUNT (It should be 1454 instead of 1444) Checking Catalog file Missing thread record (id = 20796) INVALID SIBLING LINK VOLUME CHECK FAILED ERROR: FILESYSTEM VERIFY OR REPAIR FAILED
I don't know where to go from here! Please help, I'm not Mac savy, so any suggestions need to be specific.
I had 2 partitons and i wanted to install XP using boot camp, of course i have to make my hard disk 1 partition, so i deleted the second partition and resized my 1st partition, when i try to resize 1st partition i get this error: filesystem verify and repair failed
I have a MacBook Pro intel i7 Chip. I am running disk permissions and its taking a long time and showing Open error 5 on the details list. I am letting it do its thing but im curius as to what this error is and why its taking so long in the utility. I see in some other postings that sometimes it te signs of a bad drive and sometimes not. it is the Toshiba 750GB drive.
I have 4 Discs.Mirrored raid sets One Raid Slice is 'System Mirror'One Raid Slice is 'Data Mirror' There is a lock symbol on all 4 discs. Status is online. I can't delete the raid sets. I can't unmount them. I am the admin but the Disk Utility says "Deleting RAID set failed. Deleting RAID set failed with the error: Invalid Request"
I have a PowerMac G3 running OS X Server 10.4.7. There is an 80GB ATA boot hard drive and a SATA card and two 250GB SATA drives. One SATA drive is existing and has data on it; I just installed the second one because I want to mirror the 1st drive onto the 2nd one.My questions are: how do I do it? When I try to create a RAID set in the Disk Utility GUI, it says all data will be destroyed. I cancelled that.So I tried diskutil enableRAID mirror disk1, which told me I could only mirror volumes.The volume name is RAID, so I tried diskutil enableRAID mirror /Volumes/RAID which gave me an error "Error enabling disk to RAID Could not unmount disk (-10000)"
My MacBook is unable to boot. Whenever I try to boot, the spinning circle and the progress bar appears on the grey screen, but when the progress bar reaches about 40%, the computer shuts itself down. I started in Verbose Mode and tried AppleJack, and it said my harddisk needs to be repaired; but AppleJack is unable to do that. (Error Messages: "Invalid node structure" and "Incorrect number of thread records) I then tried to startup with both Recovery HD and Mac OS X Install DVD and ran the Disk Utility on both of the startups. At the First Aid tab, I selected my Hard Drive (not the Hitachi one, the Macintosh HD one) and clicked on Repair Disk. The error messages I got from Repair Disk were:Invalid volume file countInvalid node structureThe volume Macintosh HD could not be verified completely.
Error: Disk Utility can't repair this disk..disk, and restore your backed-up files. And, lastly, the following popup message appeared:Disk Utility stopped repairing "Macintosh HD"Disk Utility can't repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files. Not being sure how to back-up my files using Disk Utility, I plugged in an external HDD to my USB port and clicked on the Restore tab in the Disk Utility. As the Source, I selected Macintosh HD and as the Destination, I selected one of the partitions I created on my external HDD. However, when I clicked on Restore, I got the following error message:Restore FailureCould not restore - Input/output error I partitioned my external HDD by creating 2 partitions formatted in Mac OS Extended Journal - GPT. Now, what can I do to save my files (and my MacBook's HardDisk)?
My current setup consists of my boot drive (250GB), a striped RAID (500GB) for storage and a 1TB Time Machine Drive.I have recently bought a new 1TB internal drive and would like to replace the striped raid with this drive, thus freeing up two 250GB drives - 1 which i will keep internally and the other will go into a external enclosure My question is can i just copy the files from the RAID to the new internal or do i have to use software to clone it?
I'm still working out the details on purchasing a new MacPro. My Apple sales rep tells me that I can greatly increase the launch speed of applications and the system OS by purchasing 2 hard drives and using Disk Utility to stripe them together into a "software RAID". They claim it will be faster and more reliable than a single SSD. I know I've asked this question before, but the answers were over my head. I don't know anything about SATA raid cards, or SSD's except for their benefits. But I'm pretty sure I can stripe two drives together and make a software RAID.
I just bought a Guardian Maximus RAID1 kit and I have two 1TB drives in it. I'm using it over Airport Extreme as an airdisk (mac osx 10.6.2)
My question is simply: am I running a risk by partitioning it into two partitions? Should I ever have to rebuild the failed disk (which I understand is really simple with the Guardian Maximus) - will it have trouble doing two partitions? I'm using one 500gb partition for time machine and one 500gb partition as redundant itunes/media.
I have a Lacie ext hard drive with 2 x 250gb HD that were one RAIDed into a single 500gb HD. I ran this update Lacie firmware update: http://www.lacie.com/support/drivers...r.htm?id=10053 And now my HD will only show up as two separate HDs of 250gb instead of a single RAID HD of 500gb.
