Power Mac :: Upgrading From 10.4.11 To 10.5.8 On My G4 Power Mac Digital Audio?
Mar 26, 2012
I still have the same G4 Digital Audio which came used but with a clean OS, which I managed to up grade to reach the 10.4.11. Its works great and I love it. I can only imagine using a real Mac Pro 2012. The software is legacy and It will not support the QuarkExpress9 for example. So what if I found and upgraded to the 10.5.8 or the max OS my G4 can handle? Is it worth it?
Info:
G4 Digital Audio, Mac OS X (10.4)
View 1 Replies
ADVERTISEMENT
Dec 18, 2006
Step by step instructions for using an ATX 24-pin power supply in a Gigabit Ethernet/Digital Audio Powermac G4 (one way to do it anyway): First, know that to boot the G4s up, you MUST have at least +12V of power going to the G4's pin #22 spot (white wire) even with the computer turned off. This is called standby power (I didn't know what it meant until a few days ago). ATX power supplies generally only have a +5V SB power source which is not enough. You must use some method of getting the +12V to +28V standby power to the G4's pin #22. I will outline the method I used but there are others (ideally get a ATX power supply with +12V standby, but they are not so easy to find). I am typing this on my G4/533 with an Antec SP-500 power supply. Why do this? With an ATI Radeon 9800 256mb graphics card, three hard drives, a DVD drive, a SCSI card, a USB 2.0 card, a USB 2.0 hub with four devices attached, and a newly aquired G4/1.4 Ghz card (which meant two additional fans for cooling control), I figured the original power supply was overextended. So, here's how it can be done:
1. Make sure the ATX power supply you want to use fits your case and has the power cord hookup in the correct position (lower left corner).
2. Make sure the ATX power supply has a long enough motherboard harness, or else you will need to buy an extension (which you may want to do anyway to avoid mutilating the original power supply's wiring harness).
3. About three inches from the motherboard harness connector (same with all future cuts), cut the ATX wire #8 (gray). Tape the end of the gray wire going to the power supply. You don't use it for anything.
4. Cut wire #12 (orange).
5. Remove 1/2 inch of wire insulation from the stub of gray wire coming from pin 8 in the harness connector and from the long orange wire (that used to go to pin 12) that goes to the power supply and solder them together. Cover with heat shrink tubing (which you must put on before you solder) or electrical tape......
View 10 Replies
View Related
Nov 2, 2007
I am trying to hook up the digital audio output on my cable box to the digital in on my dual 2.0 G5 running 10.4.9, 1 gig RAM. I have HDMI and component video out to monitor, but I use JBL creature speakers and sub for audio.
I have the propper cables and routing, sounds prefs set to digital in, and line out, to go to JBL creatures and first I get no sound at all. If I start AudioHijack and use same input and output settings all I can get is a hissing/clicking sort of sound. Same with using Soundsource and LineIn.
Audio MIDI Setup only shows or giveds me Built-in Audio for selections under system settings and properties for. Ausio Input and output show Master stream grayed out and I selected digital in and Line out for my sources and no change. Both ar set to 441000.0 Hz 2ch-24bit as well.
Information:
Dual 2.0 G5
Mac OS X (10.4.9)
View 2 Replies
View Related
Nov 5, 2007
I am trying to hook up the digital audio output on my cable box to the digital in on my dual 2.0 G5 running 10.4.9, 1 gig RAM. I have HDMI and component video out to monitor, but I use JBL creature speakers and sub for audio.
I have the propper cables and routing, sounds prefs set to digital in, and line out, to go to JBL creatures and first I get no sound at all. If I start AudioHijack and use same input and output settings all I can get is a hissing/clicking sort of sound. Same with using Soundsource and LineIn.
Audio MIDI Setup only shows or giveds me Built-in Audio for selections under system settings and properties for. Ausio Input and output show Master stream grayed out and I selected digital in and Line out for my sources and no change. Both ar set to 441000.0 Hz 2ch-24bit as well.
Information:
Dual 2.0 G5
View 3 Replies
View Related
Jun 19, 2010
I have found that by plugging in my Apogee Duet firewire audio interface and ONLY WHEN AppleFWAudio was loaded there was a 10c CPU raise that was making my MBP (late 2008) hot!I wanted to monitor the power that was required for Duet to run and to see if the temperature rise was due to that, so:With Apogee drivers uninstalled (just to be sure its not their drivers related, which is notMBP on battery power with System Profiler opened (to monitor the mA required by the computer from System Profiler -> Power)
View 5 Replies
View Related
Dec 4, 2007
I want to add GPS data to my digital photographs. I was thinking of using the Sony GPS-CS1 with HoudahGeo. However, I've read that there seems to be a bug which means PPC machines can't recognize the Sony device, whereas Intel Macs can. Does anyone know if this bug has been fixed. Or can they recommend an alternative GPS logger which is available in the UK.
Information:
Daul G5 2 Ghz
Mac OS X (10.4.10)
2 gigs memory, 250 gb hd
View 2 Replies
View Related
Dec 16, 2007
I have Western Digital My Book Pro II 2TB hard drive connected through FireWire 800 or 400 cable. The problem is that it shuts itself off unexpectedly all the time. Sometimes right after I turn it on, sometimes after 30 minutes. After turning it back everything seems to be fine, no loss of data. Anyone else experienced the same problem and can suggest how to fix it?
Information:
G5
Mac OS X (10.4.10)
View 7 Replies
View Related
Oct 30, 2007
I have my Xbox 360 sound out-putting through an optical digital cable to the digital input of my Dual 2.3ghz Power G5. My mac recognizes the signal but I was hoping I could somehow use the incoming sound to output through my headphone speaker jack on the front of my mac. Both my mac and xbox 360 use the same monitor.
I noticed it doesn't work that way. Is there a way to switch the incoming digital signal to route through my headphone port on the front of my mac? There has to be a way.
Information:
Powermac G5 Dual 2.3 Mhz
Mac OS X (10.4.10)
View 2 Replies
View Related
Jan 31, 2010
I recently obtained a (free) Power Mac G4 (Dual 500Mhz, AGP, Gigabit Ethernet) I am looking to upgrade the processor and video. Can anyone advise on what video card would work on this machine? Do I have to go with a Mac edition AGP card (ATI Radeon X800 Pro Mac Edition) or can I use any (PC) AGP card, for example the Radeon HD 4000 or Geforce 7 series?
View 1 Replies
View Related
Jun 3, 2012
I have a Power Mac G5 2.0 GHZ 1 TB and 250GB Hard Drive, 4 GB of Ram Running 10.5.8 Leopard. Now i bougth this mac on ebay to EDIT VIDEOS AND PICTURES. BUT, i cant do either because all the editing software requires snow leopard or higher. the Mac doesnt even have I Movie, Garage Band. To get any sort of editing software i need snow leopard. To get snow leopard i have to have an Intel Based Processor MINE ISN'T INTEL. So pretty much i have NO WAYS to edit or create videos.
Info:
PowerMac, Mac OS X (10.5.8), 2.0 GHZ, 1.2 TB.
View 9 Replies
View Related
Dec 15, 2007
I have a power mac G5 2.7 that is 2.5 years old. It came configured with two 400GB drives inside as it will only hold two. I now really want to change them out to either two 750 GB or preferably two 1TB drives. Apple, however, has told me it won't work and that my unit will not handle this huge additional power consumption. I have called mac mall and they say no way as well. OWC says they have many working like that and its never been a problem. Then I called Apple again and they said it will work fine. I have 6 more months of Apple care, but either way do not want to blow the interior of this system up. I know I need SATA drives and would ideally like to purchase the Hitachi Deskstar 7K1000.
Information:
Powermac G5
Mac OS X (10.4.3)
View 4 Replies
View Related
Oct 27, 2007
I have a Power Mac 2.3Ghz (see spec in sig) with the standard 250GB Maxtor 6B25050 hard drive. I was wondering, how I could increase the speed of the computer? If I upgrade the hard drive to something like a Western Digital Raptor X 150GB 10kRPM SATA drive would this provide any performance increase over the standard disk? Memory-wise I never have any "page outs", so I understand that a memory upgrade will not increase the speed of my computer.
Information:
Power Mac G5 2.3GHz, 1GB Ram, ATI Radeon 9650, Bluetooth KB and Mous
Mac OS X (10.4.10)
IBook 800MHz, 512MB ram
View 2 Replies
View Related
Oct 5, 2007
I've been doing some searching and can't find any threads regarding capturing audio (cassette tape) to a mac. Wanted to rip some old school tunes from some tapes and convert to MP3. I connected an old tape deck to my G5 via ADS Pyro A/V Link (RCA audio input to Pyro, firewire connection out to G5), that doesn't seem to work. I've also tried connecting to my iMic USB, but that's not picking up any audio either. I've tried using QT audio recording, iMovie, FCP, and Analogue Ripper with no luck. They recognize the Pyro and iMic, but not picking up audio.
Information:
G5 Dual 1.8Ghz (Q37), 4.5GB ram, Pioneer 112D burner (internal)
Mac OS X (10.4.10)
320GB + 500GB SATA HDDs, Radeon 9600 Pro Mac 256MB, LaCie firewire burner (ext)
View 8 Replies
View Related
Dec 7, 2007
I've got a G5 DP with the infamous white noise problem coming through my speakers that was only fixed after downloading the chud tools and disabling the NAP settings - does anyone know if I'll have the same issues if I install Leopard? Want to upgrade but don't want to waste my money if the noise comes back and I can't get it to work. Also, I'm using an m-audio firewire 410 that doesn't have drivers yet; has anyone used the Tiger drivers with success on Leopard?
View 5 Replies
View Related
Dec 9, 2007
I'm coming from a good 7-8 years with an old G4, so forgive the ignorance. On that one, I added a PCI audio card to connect with some Altec Lansing speakers with Sub-woofer & simulated Surround sound. It sounded great. hat's your suggestion? Get a similar card for the G5?Or get some new speakers that will sound as good?I don't know anything about digital audio out. Does that connect to speakers, or only tuners?
Information:
G5 tower
Mac OS X (10.5.1)
View 2 Replies
View Related
Sep 12, 2014
I thought you should be able to.Play iTunes audio out through USB to a receiver equipt with USB mode as I can with my iPad Air, but I can,t find in preferences on my 2013 iMac any out put and I get no signal to the receiver/amp. Is it possible? What am I doing wrong?
Info:
iMac (27-inch, Late 2012), OS X Mavericks (10.9.4)
View 7 Replies
View Related
Mar 19, 2008
My girlfriend has a 12 inch Powerbook G4. She noticed that the battery life was starting to dwindle. Tonight, she tried using it. It wouldn't power up. The battery indicator showed one flickering power circle. The adaptor has the green circle on it, indicating the battery has a full charge. However, the computer won't charge up.I've read the 12 inchers don't have separate PMUs. Could that prevent the machine from starting? She was using it earlier this evening, as she e-mailed me pictures from our vacation.
View 10 Replies
View Related
Feb 10, 2008
I have a iBook G4 laptop and there seems to be something very wrong with it. It started a few days ago just randomly. I was reading something on the internet and the screen went black on me, but the power was still on (I clicked CAPS LOCK to see if there was power). I then proceeded to push the power button and the power went off. When I pressed the power button again to turn it on, it made that internal noise it always makes and then the fan came on, and wouldn't turn off. There was no picture on the screen at all. Completely dead. But there was power, because when I clicked on the CAPS LOCK, the light came on). I tried pressing on the power button for at least 15 seconds and even went as long as a minute, and the power didn't go off.
View 3 Replies
View Related
Apr 18, 2008
I had a bad power surge (USB hub that was plugged into the back of the display had the wrong power cord plugged in... very stupid mistake I know!!) take out my 23" Cinema Display. The display shows no sign of life (no power light, etc) and the brick has been tested and is OK. My local service place says that they will have to send the display back to Apple which means a minimum of $400 for repair so I'm wondering if anyone has had a similar issue that they resolved successfully? The service place suggested that Apple would replace the logic board but is there any way to test to see if this is the main issue? I have seen logic boards sold separately online but would be hesitant to buy it without know that this would fix this issue.
View 10 Replies
View Related
Nov 8, 2007
I made this a new topic because I think it is important enough to do so. Probably most of those that originally complained about this have moved on to the new MacPro but I am sure there are still enough G5 owners out there that still have concerns about this topic.
A clean install of Leopard eliminates the infamous power supply beeping
Its amazing, my G5 is like a new machine; no more of the annoying power supply beep; although, I learned to live with it after a while and didn't even notice it. However, the silence is now very noticeable.
View 2 Replies
View Related
Nov 19, 2007
Where can I obtain a new 23 Inch Cinema Display power adapter? I've searched the Apple Store but I cannot find it.
Information:
G5 Dual Core PowerPC
Mac OS X (10.5.1)
23 Inch Cinema Display
View 1 Replies
View Related
May 29, 2012
a friend recently gave me a g5 power mac that had some issues, and the failure was described as intermittant. The machine supposedly would work properly when booted and start freezing up after time, but if turned on the next day it would work properly for some time. I assumed it was an overheating issue, but apperently there is more to the picture. I have tried booting the machine quite a few times and the display always reads no signal. The machine sounds as if it were booting normally, but there is not output. At first I assumed it was my display cable, which was a DVI-D single link, however the DVI-D dual link cable leads to the same result. Is it nessicary to have a DVI-I cable? None of the error LEDs light up on the motherboard. After doing some hunting I haven't found anyone with the same issue, but I am wondering if I should assume the graphics card is dead. What steps do I need to take to isolate a graphics card failure in a power mac g5?
View 3 Replies
View Related
May 9, 2012
Why can't I hear my music keyboard when it is connected thru the Analog Audio line-in port? Looking at the System Pref. - Sound menu - in-put - Line in Built-in Audio, I can see activity on the input levels when I press the Kawai piano keyboard but no sound is heard. All other sound systems- I-tunes etc are operating properly.
Info:
power mac G5, Mac OS X (10.5.8)
View 1 Replies
View Related
Oct 8, 2007
I hav" a "late 2004" G5 2.0 dual processor. To upgrade graphics card, I find many require a power supply splitter. Do I have a molex 4-pin connector? I can't see the location inside the box.
Information:
G5 dual 2.0, 2.5Gb
Mac OS X (10.4.3)
View 1 Replies
View Related
Nov 18, 2007
I have the problem that I need to frequently power cycle (shut off and on) my dsl modem to maintain a reasonable speed with my internet connection. It is making the internet experience pretty user unfriendly. Does any one know whether there is a way to optimize my internet connection such that this is not required so frequently (couple times a day)? I am on my second dsl modem, and the same problem has occurred with each of them. ATT simply advises me that my solution is to power cycle the modem to sync the system, whatever that means.
Information:
Power Mac Dual 2.0 GHz
Mac OS X (10.5.1)
ATT DSL Internet Connection
View 4 Replies
View Related
Dec 6, 2007
I added 2 sticks of 512 to my power mac g5 1.6. I had ahard time getting the computer to see the new ram, but finally was able to kinda get it working after zapping the pram. However my computer only saw these 2 sticks as 256, odd. So i attempted to troubleshoot the problem. I tried just installing the new ram, but the computer wouldnt boot. I tried a few different combos with the other 4 sticks i had, but nothing. I put the old memory back in, and still nothing. The power led looks to blink once every five seconds or so. I tried pressing the pmu reset button, but still the same out come. I also tried taking out the battery, nothing.
Information:
1.6 g5 single proc
Mac OS X (10.5.1)
View 15 Replies
View Related
Dec 13, 2007
I had a weird issue this morning. I started computer and it did not make the chime sound, it didn't do anything at all. I disconnected it from the extension cord as well as all the peripherals attached to it and nothing. I tried a different start up disk and again there wasn't a sound. Then i unplugged it and reset the SMU on the mother board and air sprayed the computer to remove all dust. Then plugged it back and it came back on.
Information:
Power Mac G5 Dual 1.8
Mac OS X (10.4.11)
View 5 Replies
View Related
Oct 7, 2006
I'm using a B&W Power Mac G3 with 512MB RAM and OS X Tiger for a SMB file server (with 5 users) and a USB printer server. Everything is working good, but I have a problem.
It doesn't have a monitor or keyboard/mouse attached normally (I can configure it via VNC). The problem is that I would like to be able to turn the machine off when it's not needed (like at night sometimes, days when I won't be home, etc.). I would like to just hit the power button and have it turn off, however it puts it to sleep instead.
Normally, sleep would be fine, except on the B&W, the fans still run, just the HDs shut off, so it's still noisy as heck.
Is there a way to make the power button shut it off? If not, any other easy methods of shutting it off you can think of? Via VNC won't cut it, as my dad needs to be able to turn it on (not a problem) or off as well.
View 9 Replies
View Related
Mar 21, 2009
i just got my new imac 2 days ago. I was wondering is there another to turn on the power without pressing the power from button? (cuz i remember u can power on from the keyboard b4)
View 7 Replies
View Related
Jun 26, 2009
Anyone know where I can buy an extra AC cable for the MagSafe 85W power supply that came with my late 08 MBP? I'd like an extra cable and I'm not interested in ponying up the dough for the entire power supply. I checked the Apple Store and Macmall, but haven't found anything as of yet.
View 3 Replies
View Related
