MacBook :: Disk Utility Cannot Find New 320 GB Drive
Feb 13, 2009
I'm fairly Technical, I just can't seem to figure this one out. I own a 13 Inch Macbook with the stock 120 GB HD. It was purchased this past September 2008. I bought a new HD from Newegg. Here is the link to the HD. [URL]
I read the reviews, and more than 20 reviews I read said this HD worked perfectly in their Macbook.
-So I received the HD yesterday
-I put it inside my laptop
-I put in the OSX install CD
-I powered up and held down C and booted into OSX Installer
-From the menu I selected Disk Utility but the hard drive does not show up as listed hard drives
After all attempts failed, I put the disk in my windows machine as an extra sata drive, and it booted perfectly fine, so I know the disk is ok. Some other thoughts?
-The difference between the stock and new HD is size and also 1.5 GB vs 3.0 GB Transer rate
-Does my Macbook need a firmware upgrade - I doubt this, but just a thought
-Does the Macbook not recognize unformatted disks - I doubt this too.
View 11 Replies
ADVERTISEMENT
Aug 18, 2010
I have a dual 1.25 ghz MDD Powermac G4. It was working fine until a couple of days ago. It froze up, I restarted it. I got a blank blue screen.
Also, the computer made some awful clicky noises that I've never heard before.
I booted from the OS X installation CD. Disk utility lists the WD1800 hard drive, but I can't do a re-install and there's no option to repair it.
I can't erase or partition it because when I try, I get a failure message saying it can't be done ("chosen size not valid for chosen filesystem"). The HD is listed in system profiler... with a capacity of 0 bytes.
I assumed that the hard drive had died, so I went to a local PC shop and bought the only IDE drive they had (a Maxtor 6l250r0). I installed it, then booted from the OS X CD.
I know that new hard drives need to be formatted, but I assumed that this could be done with disk utility.
But disk utility can't find the new hard drive, doesn't list in the left column. It shows the optical drives and the install CD and the old WD hard drive which can't be erased or repaired, but no new hard drive.
It's not listed in the system profiler, either.
I checked the cable connections and tried installing it in the front carrier rather than the rear, but nothing works - disk utility and system profiler can't recognize it.
The only other desktop mac I have access to right now is my old 450 mhz Sawtooth G4. I tried putting the HD into the sawtooth and got the same results - disk utility and system profiler can't find the new HD at all, but has no trouble finding the old 20gb HD and the DVD and zip drives.
I'm... not really sure what to do here. Am I doing something wrong?
View 1 Replies
View Related
May 7, 2012
I had to power off my iMac by Pressing the power key and holding it several times over the last few weeks. The last time it wouldn't reboot - I'd just get an apple icon. When I tried a safe boot I'd get the icon and it would change to a no entry sign.Next I started up from the snow leopard installation disk with the intent of repairing the iMac disk. The installation disk worked but when I opened disk utility it only found the installation disk. It didn't find the iMac disk.
Info:iMac, Mac OS X (10.6.5)
View 3 Replies
View Related
Jun 27, 2014
I have a Seagate 1 TB Backup Plus Drive which was working perfectly fine until I plugged it into a USB hub. It detected it while in the hub and I was able to get files off of it, but when I ejected it from the hub and put it back into the USB slot on the computer it was not detected by finder. It shows up in the disk utility and I clicked verify and repair and it says:
Verify and Repair volume “Seagate Backup Plus Drive”
Checking file system
Volume repair complete.
Updating boot support partitions for the volume as required.
Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
Is there any way to get this to work properly again? Or if not is there a way for me to recover my files on the external hard drive?
I have a Macbook PRO late 2011 running OS X Mavericks.
View 1 Replies
View Related
Dec 31, 2009
I am quite new in Mac OS X 10.5 (leopard). I just downloaded from windows msdn a .iso file (with the XP Operating system). Now I want to burn it on a CD. I found on the internet that I can do this with disk utility. Disk Utility should be under Applications/Utilities. But it is not there, I don't find it in finder anywhere. (The computer was installed by the vendor). Do I need to install it from my installation disks? I already looked to disk 1, but I do not know what to install.
View 1 Replies
View Related
Apr 24, 2012
I have a 2TB Western Digital My Book Studio FW800 external that has 5 partitions, connected to my 2011 iMac. I had help doing the partitions and don't really remember the reasoning, but one is just for my SuperDuper! backup, one is Miscellaneous, one for movie clips off my camcorder, one for misc scanned photo's and one for my genealogy research. I back up using Time Machine to a Time Capsule and also to this WD hard drive with SuperDuper!
Recently I'm getting a pop up message that "Mac OS X can't repair the disk "Genealogy"'. And it needs to be reformatted. It's become a read only disk. When I look in Disk Utility it shows all the partitions as "Mac OS Extended (Journaled)" EXCEPT for the one in question. I also noticed that there are a lot of files with "date created" being the same date in 1969! These files may be letters I've written or photo's I added to that partition within the last few years.
I think I have to completely reformat the entire external hard drive to repair this, but I want to make sure. Because it's going to be a major hassle backing it all up to another external (having to get one first) and then figuring out how to make the files that have turned "read only" in that one partition, back to their original state! Does this sound right, that I have to reformat the entire external hard drive? And how do I get the read-only files back to their original state.
Info:
iMac, Mac OS X (10.7.3)
View 3 Replies
View Related
Jan 19, 2010
the past couple of days my new macbook Pro (only had it a couple of months) has been really slow to boot, with a grey progress bar that I have never seen before. I googled it, and you all know what i found.
So I ran the disk utility, and selected analyze or whatever the button is, and it said I should load it from the INstall DVD, as the disk needs repairing.
Guess what. The disk cannot be repaired.
An error message about expecting 31 files but only finding 30?
It recommends erasing the disk and reinstalling from scratch.
Now, as far as I can see, apart form the slow boot times, everything else still works. Does this mean that it is just a ticking time-bomb that will break any time, or is just a couple of corrupt files that don't matter?
This is really annoying, I love my Mac, but having to reinstall so soon after purchase?
Apologies if there any other posts on here already, it is late, I am stressed, and would like a nice person to help me out.
View 6 Replies
View Related
Feb 22, 2010
I ran installer then went to disk utility and pushed disk repair. it ran and indicated in green that no repairs were necessary. i then went to startup disk and only the Diks and network startup showed up but no hard drive. i also open computer to make sure was not wet muddy due to leak in cooling system but all was dry
View 1 Replies
View Related
Apr 13, 2010
My macbook hard drive crashed, luckily I had just backed up everything. I went and bought a new 320 GB hard drive, I researched and I know it's compatible with my Macbook. I decided to install windows 7 on it first, but the windows 7 installer wouldn't recognize my hard drive. (For the record, my Matsushita superdrive will not read DVDs anymore, only CDs, so I created bootable copies of both my Mac OS X install disk and my Windows 7 install disk, and I've been using a bootable rEFIt CD to boot from my USB flash drive.)
So I booted up the Mac OS X Snow Leopard disk and started disk utility - it recognizes the rEFIt CD, it recognizes the flash drive, but no internal hard drive. The partitioning tool in rEFIt doesn't recognize it either, but I know it's seated correctly because I can hear/feel it booting up with the computer (if i remove the battery and boot with the computer plugged in). I also know it works correctly because I installed it in my girlfriends PC and it recognized it just fine, I even installed Windows 7 on it, hoping the macbook would boot from it.
View 8 Replies
View Related
Apr 18, 2010
Can I make a disk image of my current MB Pro (early 2008) and copy it to my new i7 MB Pro to retain all my docs and programs?
View 13 Replies
View Related
Aug 2, 2010
Just installed a new HDD into a macbook pro that was dropped. Seems fine, loads the disk and then says it can install the OS, i load up disk utility and theres no hard drive int he list just the optical drive and the DVD, its not the disk that came with the mac itself its either my proper retail one or the one that came with my personal older macbook which might be the issue. Ive taken apart and reconnected the HDD and all seems fine internally. Are there any issues that cause this except not using a full retail disk which im going to try later on, just wanted to rule everything else out.
View 7 Replies
View Related
Aug 31, 2010
The HDD in my wife's black MacBook (2007, I think) won't boot up. I've run Disk Utility and have decided it's pretty much dead. I have a Carbon Copy backup, so the data is fine. I've tried replacing the drive twice now, and the MacBook simply won't "see" the new drives. When I install the drive, nothing shows up in Disk Utility (run either from the install disc or the Carbon Copy backup drive in a USB enclosure).
The new drives are formatted (I even copied the bootable backup to one of them), and the computer sees them just fine if I install them in a USB enclosure and hook them up that way. When I put them in the computer, though, no dice. Her old, corrupted HDD still showed up in Disk Utility when I reinstalled it, but the new drives don't.
View 6 Replies
View Related
Dec 25, 2010
I got a second hand macbook pro on tuesday, it is the 13" 2010 model and is two months old. However it keeps causing me all kinds of problems, and I am not sure if it is my fault, a hardware fault or something else. I'll describe what I've done to it; When I got it I wiped the hard drive and did a clean install of OSX, then I imported everything from my old mac through migration assistant. However when I then started using my new mac, the 'home' folder was a different name so some files didn't match up, like my dropbox account and some games. I don't know if this has caused other problems within the directories or anything like that.
It is usually fine for about 6 hours, it's pretty quick and I have been through disk utility in this time and the verify process has been ok. However after this time the it starts being really slow. Like I'm talking 10 - 15 minutes to open an application. Every time this happens I open disk utility to check on it, and it always needs to be repaired as there are folders and directories missing. However when I turn it off and go into disc utility through the install disc it doesn't let me repair it as the drive cannot be unmounted, but then the HD disappears from disk utility completely.
On top of this I tried to install XP through boot camp earlier, but the partition wouldn't format, so I went back through boot camp assistant and deleted the partition. However whenever I turn it on I have to hold down the command key and select the Macintosh HD, because if i don't it tries to boot into windows, even though the partition has been deleted and the HD merged back into the Mac HD. When I boot through the command key, the only option there is the Mac HD, so I don't know where it is getting windows from.
The battery is not what I expected in this thing either. I have put this on another post but I wanted to complain about it again. I have noticed that on a full charge i only get 6 - 7 hours browsing the internet, way off the 'approximately 10 hours'. When I go into istat menus apparently it has a cycle count of 68 and the health of the battery is 89%, which seems very low to me. Whenever I do manage to get it to turn on, it never remembers my settings for the back lit keyboard or the screen brightness. They are always on full whack even though I turn them down to half every time I use it.
Basically, on this fine christmas day (don't get me started on that, the dog got more presents than I did and now my mum is singing Susan Boyle at the top of her lungs) I was wondering if any of you could help me with these problems? I'm thinking I may just have to wipe the HD again and reimport everything manually but I really don't want to do that. I do love Apple Macs and I don't want to get rid of this thing, but it is driving me mental. I turned the Macbook Pro on when I started writing this on my old Macbook. It is now 8 minutes later and it has still not booted. It is just sat there looking all smug with the spinny thing below the apple on the grey screen.
View 18 Replies
View Related
Dec 28, 2010
However, my hard drive appears to be running fine - haven't noticed any degradation of performance since receiving the warnings two days ago. And HD is still running quiet (no strange mechanical noises I'm accustomed to hearing prior to a failure). Nevertheless, I'm installing a new HD tomorrow and recloning it from a backup external drive (operating from external until then).
View 4 Replies
View Related
Nov 9, 2010
I'm trying to install Windows 7 on my mac. I'm using bootcamp assistant to try and partition my hard drive, but it gives me an error saying it cannot partition it because of unmovable files or something along those lines. Is there any way to get around it, and if I do use my OSX install disk and run disk utility to repair the drive will my files be deleted?
View 4 Replies
View Related
Jun 14, 2012
After backing up my data and then swiping my hard drive using Disk Utility, my OS seems to have been uninstalled as well. Is there a way to recover the deleted information and go back to the last working configuration? I'm on a MBP IC2D 2.16 w/ Lion.
View 3 Replies
View Related
Aug 29, 2014
I've recently converted to the Mac-side:
I'm having difficulty with my external hard-drive, here's the info on that one:
Disk Utility won't allow me to mount the drive, I've tried using a number of softwares to read it (working under the assumption that it's an NTFS drive), including Tuxera and Paragon. I have too much stored on the hard drive to empty it back onto my old computer, and so I'm not able order to re-format it.
Info:
MacBook Air, OS X Mavericks (10.9.4)
View 1 Replies
View Related
Jun 10, 2012
I had downloaded some files to add to an external hard drive, the hard drive was assigned to a pc before adding these files so it wouldn't let me add files from my MacBook..
Had a look around online and made some changes (well thats what I thought) and I was able to transfer files form my MacBook onto the external hard drive.
What I then figured out was that there was nothing left on the hard drive except for the two file sI just transferred..
It turns out I deleted everyting without noticing.
The stpes I followed was to go to disk utility then select the hard drive and click erase (not knowing this would erase evrything).
So now I have two files on my hard drive and no idea how to recover the 'delted' files.
I tried using Disk Drill, which found the files but then it said I need to buy the full version to recover them.
I am wondering if there is any free methods to recover these files at all
Info:
MacBook Pro (13-inch Early 2011)
View 3 Replies
View Related
Jun 17, 2009
I was working in windows using mac drive last night and I opened a dmg which I found out later was corrupted. It didn't open in windows, and windows hung to the point that I had to do a hard restart. Once everything booted back up (it took forever, btw), I found that one of my HFS drives (not the one I was working on at the time, oddly enough) had disappeared from both windows and osx. I cannot see the actual drive in device manager or disk utility, and things like diskwarrior and data recovery 2 don't see it either. I know it sounds like the hard drive failed, but is it possible that a software crash could cause the physical drive to completely fail?
View 2 Replies
View Related
Apr 15, 2012
I can't find the disk drive on my macbook pro. I think it was accidentally drug into a folder, but can't find it anywhere. how to locate this? The macbook will still play movies, but if I go to look for the drive, I can't locate it anywhere.
Info:
MacBook Pro (13-inch Early 2011), iOS 5.1
View 2 Replies
View Related
Jan 7, 2009
I have an USB external HD attached to Time Capsule. Trying to find out how one can use diskutil to do a verifyVolume on this drive. I tried something like: diskutil verifyVolume /Volumes/myDrive but it didn't work. The command is (naturally) ok with an USB external HD attached to the USB port on the Mac itself.
View 4 Replies
View Related
Mar 26, 2009
Despite the dire warnings about the Seagate drives that I read all over the place, I decided to buy this drive. Dell had a great price of $129 with free shipping.
It is going to supplement existing storage capabilities as a secondary backup so I'm covered if the drive does experience any of the problems that others have experienced. So far the drive is running great. I have copied nearly 800GB of data to it with no issues. I have the drive connected to an AEBS. I have been able to stream movies from the drive with no problems. It looks like Seagate has resolved the firmware issues that have plagued the drive in the past.
My only issue was that it was a bit of a pain to reformat the drive. For some reason disk utility would not format the drive until I created and then deleted two partitions.
View 3 Replies
View Related
May 13, 2009
I have heard or read somewhere on this forum that you can use Disk Utility to Duplicate your internal hard drive to another drive, how can you do this.
I have the stock 320GB 5400 RPM drive and I want to put in my 320GB 7200RPM with 16MB Cache, but I would rather not load and reload all the software, so how can I move the data from Stock to the new drive.
I already partitioned using GUID and erased the new 320GB drive in an external enclosure which is where the drive is sitting now connected via USB to my MINI.
View 5 Replies
View Related
May 18, 2009
I have a USB key and would like to format it under NTFS, under Disk Utility, there isn't that option. I don't really have time to google this, does someone know what to do? Is there a console command to do?
View 4 Replies
View Related
Aug 5, 2009
I ordered a second hard drive for my powermac g5.Its a 400 gig seagate drive.I power off my machine,unhooked everything and plugged in the drive.
I boot up and the drive isnt showing in disk utility.Is it something i did?
View 2 Replies
View Related
Nov 7, 2009
i just erased my external hard drive through disk utility my accident. I had VERY important files and the 1tb was full.
View 3 Replies
View Related
Dec 11, 2009
I've got an 8GB Sony Micro Vault Pen Drive that's stopped working. When I opened up Disk Utility it appears but doesn't give me the option to erase.
Can I try doing it with anything else before I bin it and buy a new one.
View 4 Replies
View Related
Jan 4, 2010
I am going away traveling and need to back up all my stuff off of my mac for the first time.. (pics, music etc the usual). I brought a WD Elements 500GB External Hard Drive and when I plug it into my mac book (OSx) it appears in finder, and the desktop but I can't drag and drop nothing into it. Apparently I have to format it! So have researched about formatting it, but I don't have "Disk Utility" in my utilities? My Mac was given to me from a friend second hand so i don't have the disks etc to get it. Any other way of formatting my Hard drive or a link to download disk utilities or any alternatives!
View 5 Replies
View Related
Mar 31, 2009
I've been backing up my Powerbook G4 for a few months using Time Machine to an external firewire drive with two partitions; one for the backups, and a much larger one for all my music, video, pictures, etc. I got a new mac mini over the weekend and I want to format the Time Machine partition without erasing the one with all my other files so I can start backing up the Mini.
Is this possible using Disk Utility? If so, how?
Both computers are running Leopard.
View 1 Replies
View Related
Aug 19, 2009
I've got an external drive (320GB) that I'm trying to format as FAT32 using Disk Utility, then create a large (as in, most of the drive) HFS partition.
The problem is that no matter what I do, it will only format the drive as Mac Journaled. It lets me select other options (Mac, FAT32) and goes through the process with no errors or warnings, but when I click on the drive it remains Journaled with a partition of whatever I just selected.
I am sure beyond the shadow of a doubt that I am selecting the drive itself, not the partition, when formatting. This is extremely frustrating. Google searches aren't turning up any clues and I don't know what to do.
I have other external drives formatted as FAT32 with a large Mac partition so I know it's possible.
I need to do this so I can mount the drive on a Windows machine.
View 13 Replies
View Related
