My Mac is beginning to run low on free HDD space. I'd like to add a second internal HDD to boost space. However, I don't like having a completely separate HDD icons because I can never remember which files are on which disk, not to mention a lot of copying between the two.
I'm considering adding a second HDD and combining the two into a RAID setup. Do I have to reformat my existing disk, or can I just add the second HDD's storage onto my existing disk with Disk Utility?
If I can just pop in a second HDD and add its capacity to the existing one's, that'd be ideal. Having to clear off the existing disk before joining the two would be a chore, though.
I have 2ea 250GB internal HD. One with my apps and system on it and the other with no data. How do I mirror my drive with the apps and system? Or is that possible?
Information: Dual 2.3ghz PowerPC G5 Mac OS X (10.4.10) 8 GB ram / 2ea. 250 GB internal HD
I have a PowerMac G5 and need to purchase an internal RAID card to create a RAID 1 mirror of the system drive... one that will allow me create a Hardware RAID 1 mirror, not software RAID through OS X.
I just bought a Guardian Maximus RAID1 kit and I have two 1TB drives in it. I'm using it over Airport Extreme as an airdisk (mac osx 10.6.2)
My question is simply: am I running a risk by partitioning it into two partitions? Should I ever have to rebuild the failed disk (which I understand is really simple with the Guardian Maximus) - will it have trouble doing two partitions? I'm using one 500gb partition for time machine and one 500gb partition as redundant itunes/media.
I have a Lacie ext hard drive with 2 x 250gb HD that were one RAIDed into a single 500gb HD. I ran this update Lacie firmware update: http://www.lacie.com/support/drivers...r.htm?id=10053 And now my HD will only show up as two separate HDs of 250gb instead of a single RAID HD of 500gb.
Is it possible to get a highpoint raid controller and put those 4 drives in a raid 5 array (and then create partitions inside that array) - or do you need to have 1 drive by itself for the operating system, and then create a raid array using the remaining 3 drives?
Lastly, are the highpoint 3500 series a decent card? and fully compatible?
I have a new Mac Pro Quad 2.93 with the Mac RAID card installed with four 1TB drives setup in a RAID 5 array. When creating the volumes in the RAID utility, you can not edit them, resize, etc. If one large volume is created in the RAID utility, you can then partition that one volume using the Apple Disk Utility, which then allows you to resize if needed.
I'm using the software RAID right now. Everything is set as RAID 10. I want to move to a RAID card� if I keep it as RAID 10 will I still need to redo everything?
ive put 4 of the hitachi 1tbs in my new mac pro.. and i really want to do Raid on them eventually.. and buy the pricey apple raid card.. i'll do it.. but speed wise:
How fast is a Sata connection straight from HD>Motherboard... ~75mb/s? Is the Raid 5 config with all those drives much faster... around ~110mb/s?
Do you know if there is anyway to get a 5th drive into the raid 5 array? using the ODD space.. or some externals too... i need as much as space as possible...
And boot camp wont work with raid card anymore? I was thinking to have the startup disc be a raptor to increase speed on the apps, how would it integrate with the raid card, etc
I have a RAID 0 set up with two 1.5TB HDs. I am doing some reorganizing and want to take all the data on the RAID 0 and move it to one of the hard drives in the RAID 0 and create to single drives. Is there any way of moving all the data from a RAID 0 onto one of the HDs?
I am planning on getting a 2010 MP when they come and have a question about it. I am 90% sure that with my budget, I will not be able to after a RAID card. I am wondering if software RAID would be alright or if it's so bad it's not worth doing. Also, there is small chance that I could buy a RAID card later on, how would I install it? I will be using it for 3D animation with Maya and some zbrush modeling. Also I will be doing some Photoshop and illustrator and maybe some gaming on win 7 boot camp. Feel free to list any other pros and cons about either a software RAID or hardware RAID, I wana make sure I have all the details before making a final decision on it.
I have never setup RAID before and this question may be totally stupid for that matter.
Can I setup RAID 1 (or call it mirroring) without the RAID card? I have two 1TB internal drives in my Mac Pro and I want to mirror them. I don't want to spend another 700 bucks just to setup a mirror.
Disk Utility shows some RAID options, but I am not sure how to use them, or if they will work at all without the RAID card.
My girlfriend has a 12 inch Powerbook G4. She noticed that the battery life was starting to dwindle. Tonight, she tried using it. It wouldn't power up. The battery indicator showed one flickering power circle. The adaptor has the green circle on it, indicating the battery has a full charge. However, the computer won't charge up.I've read the 12 inchers don't have separate PMUs. Could that prevent the machine from starting? She was using it earlier this evening, as she e-mailed me pictures from our vacation.
I have a iBook G4 laptop and there seems to be something very wrong with it. It started a few days ago just randomly. I was reading something on the internet and the screen went black on me, but the power was still on (I clicked CAPS LOCK to see if there was power). I then proceeded to push the power button and the power went off. When I pressed the power button again to turn it on, it made that internal noise it always makes and then the fan came on, and wouldn't turn off. There was no picture on the screen at all. Completely dead. But there was power, because when I clicked on the CAPS LOCK, the light came on). I tried pressing on the power button for at least 15 seconds and even went as long as a minute, and the power didn't go off.
I had a bad power surge (USB hub that was plugged into the back of the display had the wrong power cord plugged in... very stupid mistake I know!!) take out my 23" Cinema Display. The display shows no sign of life (no power light, etc) and the brick has been tested and is OK. My local service place says that they will have to send the display back to Apple which means a minimum of $400 for repair so I'm wondering if anyone has had a similar issue that they resolved successfully? The service place suggested that Apple would replace the logic board but is there any way to test to see if this is the main issue? I have seen logic boards sold separately online but would be hesitant to buy it without know that this would fix this issue.
I made this a new topic because I think it is important enough to do so. Probably most of those that originally complained about this have moved on to the new MacPro but I am sure there are still enough G5 owners out there that still have concerns about this topic.
A clean install of Leopard eliminates the infamous power supply beeping
Its amazing, my G5 is like a new machine; no more of the annoying power supply beep; although, I learned to live with it after a while and didn't even notice it. However, the silence is now very noticeable.
I have found that by plugging in my Apogee Duet firewire audio interface and ONLY WHEN AppleFWAudio was loaded there was a 10c CPU raise that was making my MBP (late 2008) hot!I wanted to monitor the power that was required for Duet to run and to see if the temperature rise was due to that, so:With Apogee drivers uninstalled (just to be sure its not their drivers related, which is notMBP on battery power with System Profiler opened (to monitor the mA required by the computer from System Profiler -> Power)
a friend recently gave me a g5 power mac that had some issues, and the failure was described as intermittant. The machine supposedly would work properly when booted and start freezing up after time, but if turned on the next day it would work properly for some time. I assumed it was an overheating issue, but apperently there is more to the picture. I have tried booting the machine quite a few times and the display always reads no signal. The machine sounds as if it were booting normally, but there is not output. At first I assumed it was my display cable, which was a DVI-D single link, however the DVI-D dual link cable leads to the same result. Is it nessicary to have a DVI-I cable? None of the error LEDs light up on the motherboard. After doing some hunting I haven't found anyone with the same issue, but I am wondering if I should assume the graphics card is dead. What steps do I need to take to isolate a graphics card failure in a power mac g5?
Currently I have a stock 320G drive installed with a 750G F1 Spinpoint installed as a Time Machine. I have maxed the 320 out so I'm looking to get a bigger drive.
Question: looking at the F1 Spinpoints, should I do 1x750 with 32M cache? Or 2x400G in a software RAID0? The 400s have a 16 Meg cache, so 32M total.
What's better? Do you think I'll see a better performance boost by striping over 2 drives with 16M cache each, or sticking with 1 drive with a 32M cache? And with the 2x400, I'll gain about 50 Gigs of storage over the 750G drive.
2x400 is $156 1x750 is $125
Is this a decent boost for only an additional $25, or should I just save a drive bay and get 1 drive?
I hav" a "late 2004" G5 2.0 dual processor. To upgrade graphics card, I find many require a power supply splitter. Do I have a molex 4-pin connector? I can't see the location inside the box.
I have the problem that I need to frequently power cycle (shut off and on) my dsl modem to maintain a reasonable speed with my internet connection. It is making the internet experience pretty user unfriendly. Does any one know whether there is a way to optimize my internet connection such that this is not required so frequently (couple times a day)? I am on my second dsl modem, and the same problem has occurred with each of them. ATT simply advises me that my solution is to power cycle the modem to sync the system, whatever that means.
Information: Power Mac Dual 2.0 GHz Mac OS X (10.5.1) ATT DSL Internet Connection
I added 2 sticks of 512 to my power mac g5 1.6. I had ahard time getting the computer to see the new ram, but finally was able to kinda get it working after zapping the pram. However my computer only saw these 2 sticks as 256, odd. So i attempted to troubleshoot the problem. I tried just installing the new ram, but the computer wouldnt boot. I tried a few different combos with the other 4 sticks i had, but nothing. I put the old memory back in, and still nothing. The power led looks to blink once every five seconds or so. I tried pressing the pmu reset button, but still the same out come. I also tried taking out the battery, nothing.
I had a weird issue this morning. I started computer and it did not make the chime sound, it didn't do anything at all. I disconnected it from the extension cord as well as all the peripherals attached to it and nothing. I tried a different start up disk and again there wasn't a sound. Then i unplugged it and reset the SMU on the mother board and air sprayed the computer to remove all dust. Then plugged it back and it came back on.
Information: Power Mac G5 Dual 1.8 Mac OS X (10.4.11)
I'm using a B&W Power Mac G3 with 512MB RAM and OS X Tiger for a SMB file server (with 5 users) and a USB printer server. Everything is working good, but I have a problem.
It doesn't have a monitor or keyboard/mouse attached normally (I can configure it via VNC). The problem is that I would like to be able to turn the machine off when it's not needed (like at night sometimes, days when I won't be home, etc.). I would like to just hit the power button and have it turn off, however it puts it to sleep instead.
Normally, sleep would be fine, except on the B&W, the fans still run, just the HDs shut off, so it's still noisy as heck.
Is there a way to make the power button shut it off? If not, any other easy methods of shutting it off you can think of? Via VNC won't cut it, as my dad needs to be able to turn it on (not a problem) or off as well.
i just got my new imac 2 days ago. I was wondering is there another to turn on the power without pressing the power from button? (cuz i remember u can power on from the keyboard b4)
