Last night I had a weird experience with my mid-2011 MacBook Pro; I went out to dinner and came back to find the cat had kicked the power cord out, draining the battery. I've had this happen before and wasn't too worried; it's always just restarted after I plugged it back in. This time, however, I plugged it in (getting, perplexingly, a green light on the cord) and nothing happened except for the sleep light slowly flashing; it didn't respond to any pressing on the power button, and the sleep light disappeared if I unplugged the cord. The battery test button on the side got one flashing light (meaning, I believe, a dead battery), which also didn't work if the computer was unplugged.
I left it plugged in while I hunted for info on the problem and about an hour later had just decided that I was going to have to take it in to the Genius Bar when it suddenly booted up. The cord light turned orange and it proceeded to fully recharge over the next two hours.†Is this normal behavior after a battery drain? Should I be concerned? Is it worth taking the computer in to get the battery checked, or some other element of the comp? (some of the things I looked at were talking about the logic board, which is not a happy thought)†iStat Pro claims the battery is at 41% health, 111 cycles, which I would think would mean it has some life in it yet.
I recently had to have my Macbook Unibody screen replaced. After they replaced the screen, they forgot to install the airport card. They had to take the computer back and replace the airport card. Now every time I turn on the airport card it literally takes like a minute to find any networks. That doesn't seem like a long time but next time you open your macbook see how long it takes to find networks. What should I do? Also when ever I click on the airport logo it says it is constantly scanning. Even when i am connected to a network.
I have a MBP, the model before the new unibody anyways the last few days the tool bar above that has the wifi battery status and so forth takes a long time to load while booting what gives ? Anyways this just started a few days ago, do not know if I had installed something to slow it down.
My MacBook Air (13-inch, mid-2013) takes a long time to connect to any wi-fi network (~ 30 seconds), including known/previously connected ones. Upon wake from sleep, the network will have disconnected and will have to reconnect, again taking about 30 seconds. Also, I notice that even when the display turns off briefly, the network will still disconnect. It does not matter which network it is. However, Power Nap notifications will still show up and be up to date upon wake, suggesting that the disconnection is happening only when I wake the computer.¬†
Things I have tried:
- removing all networks
- toggling wake for wi-fi network access and put hard disks to sleep when possible
- setting Location
- deleting all network system preference files and restarting
- resetting SMC
- restoring OS X Mavericks (10.9.3, clean install) with no recovery of network settings¬†
I have a thumb drive that if i plug it into my MacBook Air in the left usb port, it takes at least 3 minutes before it shows up on my desktop, sometimes MUCH longer.¬† If i plug it into the right USB port, it shows up after a minute.¬† If I plug this same thumb drive into a PC, it shows up within seconds.¬† If i plug a different thumb drive into either USB port on the Air, it shows up within seconds.¬†
It's a FAT32 thumb drive, and i've already tried reformatting it and the same stuff happens.¬† I've even had disk utility check it out and nothing's wrong.¬† I'd guess the thumb drive is bad but it works instantly if i plug it into a PC, so guessing that's not it.¬†It's a 10.6 MacBook Air.
I was sick of the battery life I was getting on my 15" Macbook Pro 3,1 (early 2008 model), so I went to the apple store yesterday to get a new one. I was over 400 cycles, so I had to just buy it, they wouldn't replace it for me. I expected that, so no big deal. But I wanted to treat this battery right. I got home, charged it up to 100%, let it sit at that for a few hours, and then let it drain overnight and rest at empty for a few hours. This afternoon, I plugged it back in with the intention of letting it fully charge and thus complete my battery calibration, but at around 40% charged, the cat yanked the charger cable out from my laptop. And then a little bit later, my girlfriend did it again. So, has my time been wasted here? Battery calibration is such a pain in my rear. i hate it. I use my laptop often and expect it to be available to me whenever I need it, regardless of how many other computers i own. I really don't want to deal with it again in the near future. And I may not.
Basically I have a MacBook Pro which logs in fine when I'm at work but when I'm on my home network it takes like 5 minutes to authenticate. All appearances are that it's trying to reach my work network to authenticate. Short of disabling wireless or having it prompt for my home network password before joining wireless, is there any way that I can either shorten the timeout or have it bypass network authentication when I'm at home?
My Mac Pro takes two minutes to start up.¬† It is also sluggish during normal operation.¬† I have Parallels and a external hard drive installed. Do either of these contribute to this problem? Or is there a program that can be used to defrag the hard drive. (I recall having similar problems with my IBM computer.¬† When it was defragged the performance of the unit improved).
I own a MacBook Pro (bought new in June-July 2009) and are having problems with my WiFi. I mostly use FireFox on both my mac and windows computer. I use a linksys router and have AT&T DSL. A lot of times web pages take really long times to load or do't even load at all. Web pages on my windows computer load almost fine.
I'm not sure if the OS upgrade to 10.6.3 is involved or not, but I've noticed that all of a sudden, ssh connections to my Linux box would take like 30 seconds before I'd get a prompt. I tried lots of different things to resolve the problem, but what finally worked was disabling "-Y", forwarding X11. Can anyone give any insight into this and help me resolve it so that I can forward X11 without the connection taking forever to establish?
Where else I can look what's being executed upon boot? because under process I see BlackBerry's Daemon (I'm no longer BlackBerry user, I'm okay to leave Application, but I don't want it to boot up during startup) and I'm pretty sure there is other stuff as well.
I'm running 10.5.8 on my MBA. Lately I noticed when I start terminal, the program seems to launch right away. However the terminal window stays blank for a long time before the command prompt shows up. during this time usage of Safari becomes very slow too so feels like it's hugging on to some resource.
so a few days ago I tried to install a package of new fonts using font-book. I tried to (stupidly) install something like 1500 fonts at one time, which eventually crashed my machine. When I restarted my computer, it loaded all the way to the desktop where it stalled for like 10mins and then eventually started working OK. Now everytime I restart it, the same thing happens- I get to the desktop and all that loads for the first 10 mins is the little search icon in the top right corner. I tried the restore disks and used the 'store everything in a "previous system" file' option because I am really trying to avoid a clean erase. I've also tried clearing my cache and doing a nvram clear. Nothing has worked so far. The computer is acting like it is doing a lot of extra work in the background but I can't figure out what. I am tempted to think it might have something to do with some junky fonts I tried to install but that sounds too simple. I am running a g5 Imac on 10.4.11.
Firefox works great, but when I quit the app, I have to sit and wait several minutes for it to finish quitting before closing my laptop. It's not a big deal, but it's annoying at times - especially when I'm rushing in between clients. I'd like to be able to just quit and close and off I go. Is there any way to lessen the time that it takes FF to quit?
My computer crashed last night. When I started it back up, the permissions on one of my internal drives in my Mac Pro that I store data on had changed. This caused some problems when trying to open applications with files stored on that volume (i.e. my Adobe Lightroom catalog). I fixed these issues, and then restarted my Mac. When I did, I saw this:¬†
I've since restarted my computer a few times, and it's doing this every time.¬†
Info: Mac Pro 2.8 (Early '08), Mac OS X (10.5.2), 10 GB RAM, 74GB 10k Raptor, 2x 750GB RAID, 23" ACD
Man, what's up with this? Shut down on my early 2008 MacPro (10.5.7) takes forever! I've tried resetting the PRAM and it did this with earlier versions of Leopard as well. I've reinstalled the OS twice, changed hard drives and wish I could fix this.
Since i got my 24" imac back 2 years ago, i always put it into sleep mode. I upgraded to SL a couple weeks back. Just in the past 2 days, when i put it into sleep mode, it takes a while for it to actually perform this operation. Anyone know what might be the problem?
Last week I downloaded the latest MAC OS and the latest Safari (beta) version as my Safari is extremely slow. Unfortunately this didn't solve the problem and it takes quite a long time to load pages from all sites that normally don't give any problems.
On my other computer (old Windows machine) this is working fine. This Windows computer as well as my MAC are connected via the same router to the internet, so that should not be the problem (I guess).
How can I find and solve the problem with the slow Safari?
I am new to Macs. I recently setup a router (D-Link 655) and attached my Lexmark E260dn printer to it using a static IP address 192.168.0.100. I added a printer to my MBP but when I print something it seems to take an unusually long time to find the printer. The printer dialog says "looking for printer" until it actually starts to print. I added the same printere to my aging Windows XP system using the install CD and it works as you would expect. Files begin printing immediately. What might I be doing wrong from the MBP?
Info:MacBookPro, Mac OS X (10.7.3), D-Link Dir-655 router, Lexmark E260