I have a 2007 Macbook Pro with the Nvidia 8600M card, and my screen went out. I had my logic board replaced, but my computer just doesn't feel the same. Should I be worried of any other issues?
View 2 Replies
I'm somewhat new to the forums, and found a really good deal for a brand new macbook air (rev.1). I'd like to know if it is possible to replace the logic board in my macbook air with a newer, nvidia-gfx based logic board. As in, will it fit, does the same power supply run it, same peripherals (airport, keyboard, etc) work/interface with it, etc?
View 5 Replies View RelatedI have a year old MacBook Pro with an Nvidea GeForce 8600M GT card.
I recently bought Unity but it turns out the Nvidea GeForce 8600M GT graphics card isn't fully supported because of a memory leak which is a problem with the drivers.
Unity Support have told me to update my drivers. I understood Mac drivers were always built in to the OS and no drivers were available from Nvidea but I see they now have one Mac driver for another card.
What is the actual state of affairs with this graphics card does anyone know? There have been a lot of reports of faulty ones and now this.
This is a just about year old top of the range MacBook Pro and it doesn't support graphics??
I have an A1260 that looks like it's undergoing the problems repaired by this program: [URL] However, I've had this thing apart, replaced the hard drive with an SSD, the optical drive bracket is very bent from when I replaced the optical drive, my display bezel is cracked in two places and held up with duct tape, and it generally looks like hell. Will they still repair the logic board despite all the other, ahem, modifications? I could probably put the original parts back in, but despite that it will be obvious I've taken it apart. It is and was out of warranty when I performed these. Should I take it to a retail store or just call Apple and ship it to them?
View 6 Replies View RelatedI have a Rev. A 1.83ghz MacBook which my partner uses. In the last six months we have had an increasing number of problems with it. First, there were the intermittent sleep problems: delay going to sleep, failing to wake. Then it killed three batteries consecutively before Apple replaced the sleep switch and power connector unit (thank heavens for AppleCare). That was back in July. Now the same problem has recurred: the battery is dead and fails to accept charge. Got a call from Apple yesterday to say that they've switched out the logic board and that the item is ready to collect.
We have eight months left on the AppleCare and what I want to know is:
1) What exactly can we expect from a logic board replacement? Do Apple really have a stockpile of 1.83ghz logic board's floating around in case someone needs a replacement or is there any chance of a processor upgrade with this repair?.............
Last week my friend gave me their macbook for free and told me it had a fried logic board. I took it just because I wanted the learning experience. I'm a freshmen learning engineering, so if soldering/de-soldering is needed I should be fine. I'm wondering how to figure out what is wrong with the logic board, ie. if it got water damage because I was thinking maybe I could try to get replacement components for the logic board. Also it came with a 60gb hard drive, but I was wondering if I could upgrade that. I know I need a 2.5 sata drive, but I was wondering if iIhad to get the hard drive from apple or if I could just go on newegg and buy any hard drive that has 2.5" sata connection.
View 6 Replies View RelatedMy Early 08's 8600 failed recently (was still working but I got like 10fps on games and it failed the test) so I had it replaced at a few apple stores (an ordeal and frustration in and of itself). Anyways I was wondering if I need to do anything since the logic board has been replaced. Is a format necessary (for optimization and speed and for compatibility)? When I turned on my computer it gave me a warning about my clock being set to March 20, 2000 and a Y2K compatibility error. Should I be worried? All in all everything seems to be OK - unfortunately since my MAC addy changed I can't access Time Machine backups anymore and have to start a new backup
View 1 Replies View RelatedMy white late-2007 MacBook recently had its logic board repaired, and ever since then, some weird things have been happening with it. The first and most annoying thing is that connecting my external display (HP w2338h) to use my MacBook in desktop mode simply does not work like it did before. I'll connect the display, make sure mirroring is turned on, shut the lid of my MacBook, but instead of going to sleep, my MacBook will just shut off.
I'll disconnect the display and open the lid to turn it back on, and it then proceeds to show me the regular Apple boot screen...but with a status bar beneath it that I've never seen before. I've attached a picture of this. Forgot to mention that I did once get the external to mirror my MacBook, but that when I did, the picture quality wasn't quite as sharp as it was before the repair. I tried reconnecting it, and haven't been able to get it working since.
I recently had a problem where my 13" 3 yr old macbook would just blink off. then it became shorter and shorter until it would not start up. i brought it to apple who told me after inspection that it had liquid damage and the battery connector and logic board needed to be replaced for an astounding 800+ dollars. the book only cost me 1100!! i got the book back (obviously i didnt pay that, i am sane!), i fiddled with it by trying to start with just the battery. no response. with the battery and charger. starts for just seconds. and then with just the charger. walla! starts up and runs like new.
View 3 Replies View RelatedI'm going to the Apple Store on Wednesday to most likely have my logic board replaced. To those who have had this done, how long does it normally take?
Also, if they determine (for some reason) that this repair is not under warranty, will they call me first to tell me so I don't get a huge bill?
As a side note. Where are the water sensors in the 17" MacBook Pro. I haven't spilled anything on it, but I have used it in some humid situations, and I fear that some of them may have been tripped erroneously. I don't know why I fear these sensors so much, but I just do.
I have just had my logic board replaced by apple via the extended warranty covering the nvida issue. I use the machine to run some audio applications and have noticed since the replacement board was added the machine is now prone to audio glicthes and drop out of some audio.
Info:
MacBookPro 2.4GHz, 2G RAM, Penryn - MacBookPro4,1, MB133B/A, Mac OS X (10.5.2)
To make the long story short, I am a careful computer user and I treat my computer like my baby since I am a college student studying Architecture and I spend more time and money on my computer than on books and there haven been 5 replacements on this mbp that I am using right now.
My 1st hard drive crash happened 3 weeks after I bought my mbp in April 2008. I got it replaced under warranty.
2nd hard drive crash happened little after 6 months............
I noticed today that the headphone jack on my 13" MBP is not working. I recall it working within the last few days but now nothing. I see no immediate evidence of external damage or foreign object intrusion, and the MBP has not even moved from the desk where it was last used.Suppose I have to go back to the Apple Store to have it fixed, which is a bummer because I literally just had it in there like a week ago to get the optical drive replaced.If the headphone jack does not work, is it required to replace the whole logic board, or is it a part they can typically replace individually? If the logic board needs replacing, do they have to order it in, or do they sometimes keep those in stock? I'd like to know as this might require me to leave the laptop there for several days again which might need some planning on my part.
View 4 Replies View RelatedAfter my MacBook Pro 2.5's logic board failed( and was replaced under AppleCare) after owning my MBP for just 17 months, activity monitor often shows asl ( system log file) manager at about 100% CPU. Fans spin at 5000rpm. Never had this issue before the logic board replacement. Also, Safari 4.04 frequently crashes; never had this issue either before, either. Occasionally, after restarting my MBP, the Apple doesn't appear on my screen but instead I get image of a folder alternating with a question mark. When trying to use installation disk to start up, under 'select the system you want to use to start up', Mac OS 10.5.8( the OS that's on my hard drive, will not show at all...it's missing. After restarting several more times with installation disk OS 10.5.8 eventually appears as a selection. Why would these issues appear only after the LB was replaced. I suspect that the replacement logic board or its installation is not 100%. Something's not quite right there.
View 1 Replies View RelatedI got a mac mini out of warranty (core 2 duo 1.83 ghz) that just died on me. I went to the apple store and they sent it in for a diagnostic. They confirmed that the logic board is dead and will be around $350 to replaced. I'm still weighing my options and was wondering if anyone can direct me to a site that sells replacement logic boards to see if I'm better off doing the repairs myself?
View 5 Replies View RelatedMy 17 inch iMac G5 1.8ghz seems to have died. For a while it's been refusing to power up and then powering up randomly but now it wont power up at all. I've looked on the logic board and reset the SMU etc but I can only get the first LED to light up. I think this means the logic board has died. Is it worth replacing the logic board and can it be done easily myself? Or should I just bite the bullet and pay out for a new alu intel iMac? I'm in the UK btw, any ideas on logic board prices?
View 1 Replies View RelatedI have an emac, g4 with a bad logic board. Does anyone have any idea what it would take to replace this and the estimated cost?
View 1 Replies View RelatedMy girlfriend has a 12" G4 Powerbook that she claimed was getting really hot. I noticed it was as well, so I installed iStat Pro and saw that the fan was spinning at 0 RPM. So obviously something is wrong. I read a few posts on people having problems with the logic board, which would also cause the fan not to work. However, the computer runs fine, the fan just doesn't turn on when it gets hot. I haven't (and don't plan to) let it get so hot that it would shut itself off or burst in to flame or whatever happens. I understand it's out of Applecare, but I would prefer to fix it myself on the cheap. I'm perfectly capable and willing to replace the fan, but before I crack it open I would like to know if there is a simple way to see if my problem is simply a dead $30 fan, or a $500 logic board.
View 5 Replies View RelatedI have an ibook g3, 500 with os x 10.3. I bought it a long time ago in Germany, so it has a German keyboard. Yesterday I replaced the logic board, since my ibook showed signs of the well known logic board / graphics failure. That went well, graphics are working now. But, suddenly the hardware or the os does not recognize the keyboard anymore. I can not type in anything at the log in screen. No lights are working on the keypad as well. Funny thing is, that, when I hold down the apple key at the start up, this works and will get me into the start up options screen. So, I am not sure if it is a matter with the hardware or with the os.
Another thing I recognized: when I put the computer to sleep at the log in screen, the sleep led will light up, but then the ibook will immediately wake up. - This might be connected to the keyboard problem. I bought the logic board replacement in the US. Could this be the problem? Does this logic board probably have trouble with the German keyboard? Or, do you think the logic board replacement is broken as well? Would using an American keyboard help?
I recently had my logic board on my MacBook Pro replaced and when I tried to backup, Time Machine did not recognize the old backup on the drive and tries to create a new one. The drive is mounted fine.
Is there a way to continue using my old backup, or do I need to delete it and create a new one?
I recently had my logic board on my MacBook Pro replaced and when I tried to backup, Time Machine did not recognize the old backup on the drive and tries to create a new one. The drive is mounted fine.
Is there a way to continue using my old backup, or do I need to delete it and create a new one?
Taking my mbp to apple store to get my gts8600 vid card fixed or somehing and they gotta replace the logic board. i heard on here it takes a few hours but the guy said 3-4 days?
View 3 Replies View Relatedso i've got a system with a fried c2d board. i can pick up a cd board for $150 plus shipping which is good for me. to find a comparable replacement, i'm looking at ~350 and i'm just not feelin that price as im on a budget.
i'm not concerned about the speed decrease as im just trying to get this thing rebuilt.
i understand that there are different heatsink assemblys..vertical vs horizontal. however, i do not know how to tell the difference and i am also unsure whether or not my c2d heatsink will work on this board i receive.
the logicboard possess a t7300 c2d and model # is 820-2279-a, it appears.
i cant find anything on that model, except for on ebay.
and i totally cant find the serial number on this macbook. under the battery on the tray has no serial number listed, and i've read through this documentation [URL]
I got a late 2008 MBP and recently my logic board got exchanged due to my graphic card failure. However, since the work is done, a very annoying problem occurred. When I put my hand on my palm rest (right side, the hard ware side), it sounds like I am squeezing the whole thing down and it will make some very wired noises. It sounds like cracking or sth. I bring it in apple store twice and they said they do not hear anything. Anybody have a idea about this issue? Thank you very much.
View 3 Replies View RelatedSo I bought my macbook pro about a year ago, and ever since I have never update my graphic/video card. I need to update it because I am trying to play this game (Left4Dead) and It says that I should update it and I have tried playing the game without updating but when I get to the Main Menu it is blank. So I went to nvidia's website and I could not find an update for GeForce 8600M GT for mac.
View 20 Replies View RelatedI have an extra macbook (weird, right?) and an old xbox. The mac is a 13" Macbook 4,1. I want to put it in my xbox. I think I can do it but this is my first hardware mod and, to be honest, I'm scared. Does anyone see any immediate problems I'm overlooking? I chose the xbox because it can dissipate heat well and i need a tower pc, so i thought an xbox one would be cool. the challenges i can think of as of right now are:
1. proper spacing and mounting of logic board (so that nothing that shouldn't touch doesn't)
2. proper placement of airport & bluetooth cards (the xbox is sorrounded by metal, which will seriously damper any wireless connections)
3. properly mounting the Superdrive (the actual xbox DVD-ROM drive as the black xbox plastic part glued to the front. obviously, that's not an option with the drive built into the mac)
4. Finally, taking apart the mac without destroying any of the parts. Then putting the whole thing together without causing any static discharge etc.
Look, I'm a senior in high school, not a laptop repairman, but I really want to do this before I leave for college.
I have a 2007 Macbook A1226 MB896LL/A which is showing all the signs of the GPU problems common to this model. Is apple still repairing them free of charge? Laptop does not chime,the fans are running, nothing on display but you can hear the hard drive chattering, it sort of boots to the point where if you increase/decrease the volume it makes the usual clicking sound, the keyboard backlight comes on if you cover the sensors, it ejects a CD if you press the eject key.
Info:
MacBook Pro, Mac OS X (10.5.6)
8 month old MBP 15" i7 4GB RAM 500GB HDD, took it in last week to get the logic board replaced (computer wouldn't boot up) and now it is running fine, although at random times the display will go haywire and I am forced to restart the comp (manually). Why is it doing this? Do I need to update something? Is it related to the new logic board at all?
Info:
MacBook Pro, Mac OS X (10.6.8)
Both have 256 MB memory, but which is faster? I have the 8600M in my MBP and the 9400M (currently with 128MB memory, but will have 256MB once I upgrade to more ram).
View 3 Replies View RelatedI had a fault where my powerbook would not start up. Apple replaced the logic board and now the screen is a very strange colour and flickers.In the video I use the hot corner and the dog changes to the right colour but the windows do not. its very strange.I will have to take it back to apple in the new year but is there anything I can do to improve the image. Its so hard to look at like this.
View 3 Replies View Related
